25.120.20 - Rolling, extruding and drawing equipment
ICS 25.120.20 Details
Rolling, extruding and drawing equipment
Walzmaschinen. Spritzmaschinen. Ziehmaschinen
Laminoirs, materiel d'extrudage et d'etirage
Valjalni stroji, stroji za vbrizgovanje in vlečni stroji
General Information
e-Library Subscription
Create subscription and get permanent access to documents within 25.120.20 - Rolling, extruding and drawing equipment
Currently subscription includes documents marked with .We are working on making all documents available within the subscription.
This document specifies the general safety requirements for cold rolling mills for flat products as defined in 3.1.
This document is applicable to: Plant (machinery, equipment, devices according Annex D) used for the manufacturing of metal cold rolled flat products from the material supply from entry (1), via the mill stand(s) (2) with roll changing devices (4), to the material removal (3) (see Figure 1).
Figure 1...
This standard does not cover:
- Thermo process equipment, e.g. in accordance with EN 746 series;
- Strip processing lines according to EN 15061, e.g. pickling line;
- Abrasive blasting plants according to EN 1248;
- Coil transporting system before coil take-over-point at the entry section and after coil take-over-point at the exit section, e.g. hook conveyors, overhead cranes, fork lift and railway trucks and other vehicles;
- Roll shop equipment;
- Hook conveyors according to EN 619;
- Non-fixed load lifting attachments, e.g. according to EN 13155;
- Storage equipment (e.g. high-bay warehouses);
- Cranes, fork lifts, trucks and railway trucks and other vehicles;
- Process technology (e.g. systems for rolling lubricant, compressed air, treatment of water, cleaning system for exhaust air);
- Firefighting system.
NOTE 1 Special requirements for protection of persons in case of using asphyxiant gases used in firefighting system is covered by this document, see Annex C.
This document deals with foreseeable significant hazards, hazardous situations and events relevant to cold rolling mills for flat products, when used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer. It provides the requirements to be met by the manufacturer to ensure the safety of persons and property during transport, commissioning, operation and de-commissioning, as well as in the event of foreseeable failures or malfunctions that can occur in the equipment.
NOTE 2 For modernization, this document (C-type standard) can be applied for the part to be modernized.
- Standard86 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the general safety requirements for hot rolling mills for flat products as defined in 3.1.
This document is applicable to: Plant (machinery, equipment, devices according Annex D) used for the manufacturing of metal hot rolled flat products from the material supply from entry (1), via the mill stands (2) with roll changing devices (6), to the exit (5) (see Figure 1).
Figure 1....
This standard does not cover:
- thermo process equipment, e.g. in accordance with the EN 746 series;
- continuous casting machines according to EN 14753;
- hook conveyors according to EN 619;
- non-fixed load lifting attachments, e.g. according to EN 13155;
- roll shop equipment;
- storage equipment (e.g. high-bay warehouses);
- cranes, fork lifts, trucks and railway trucks and other vehicles;
- process technology (e.g. treatment of water, rolling lubricant, compressed air, etc.);
- separate cleaning system for exhaust air;
- firefighting system.
NOTE 1 Special requirements for protection of persons in case of using asphyxiant gases used in firefighting system is covered by this document (see Annex C).
This document deals with significant hazards, hazardous situations or hazardous events relevant to hot rolling mills for flat products, when it is used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer. It provides the requirements to be met by the manufacturer to ensure the safety of persons and property during transport, commissioning, operation and de-commissioning, as well as in the event of foreseeable failures or malfunctions that can occur in the equipment.
NOTE 2 For modernization, this document (C-type standard) can be applied for the part to be modernized.
- Standard89 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard defines the general safety requirements for hot rolling mills for long products as defined in 3.1.
This European Standard deals with significant hazards, hazardous situations and events relevant to hot rolling mills for long products. It deals not only with circumstances where the machinery is used as intended, but also includes other conditions foreseen by the manufacturer, such as foreseeable faults, malfunctions or misuse (see Clauses 4 and 5).
This applies also to hazards arising during various phases of the life of the machinery and equipment as described in 5.4 of EN ISO 12100:2010.
This European standard applies to: Machinery and equipment used for the manufacturing of metal rolled long products from the material supply from (1), via the rolling mill process equipment (2) to (9) including preparation area (10) (exemplary layout is given in Figure 1).
The following equipment is excluded:
a) furnaces in accordance with the EN 746 series;
b) continuous casting machines according to EN 14753;
c) hook conveyors according to EN 619;
d) roll and guide shop equipment (e. g., machine-tool);
e) storage equipment (e.g., high-bay warehouses);
f) cranes, fork lifts, trucks and railway trucks and other vehicles.
This document is not applicable to rolling mills for long products, which are manufactured before the date of its publication as an EN document.
- Standard68 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard defines the general safety requirements for hot rolling mills for long products.
This European Standard deals with significant hazards, hazardous situations and events relevant to hot rolling mills for long products. It deals not only with circumstances where the machinery is used as intended, but also includes other conditions foreseen by the manufacturer, such as foreseeable faults, malfunctions or misuse.
This European standard applies to: Machinery and equipment used for the manufacturing of metal rolled long products from the material supply, via the mill stands, to the exit, including preparation area.
The following equipment is excluded:
- furnaces in accordance with series EN 746;
- continuous casting machines according to EN 14753;
- hook conveyors according to EN 619;
- roll shop equipment;
- storage equipment (e. g., high-bay warehouses);
- cranes, fork lifts, trucks and railway trucks and other vehicles.
- Standard68 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard describes the health and safety requirements of fully automated plant used in the process of tube forming, rolling and finishing (hereafter referred to as "plant"). It describes the foreseeable, significant hazards, hazardous situations, and events arising from plants and from particular machines integrated to form the plant; it does not describe the full health and safety requirements for each particular machine. It indicates preventive measures for avoiding the hazards and reducing the risks. It deals not only with circumstances where the machinery is used as intended, but also includes other conditions foreseen by the manufacturer, such as foreseeable faults, malfunctions or misuse. This European Standard specifies the requirements to ensure the safety of persons which are to be met during the design, assembly, transport, commissioning, operation, maintenance and decommissioning of the equipment. This standard assumes that installations are operated and maintained by adequately trained and competent personnel. Manual intervention for setting, adjustment and maintenance is accepted as part of the normal use of these machines.
- Standard52 pagesEnglish languagesale 10% offe-Library read for1 day
Lays down a series of outside diameters, a range of bore sizes and certain internal dimensions with their tolerances, for as-sintered pellets of hardmetal, used as wire, bar and tube drawing dies.
- Standard6 pagesEnglish languagesale 15% off
- Standard6 pagesFrench languagesale 15% off
- Standard6 pagesFrench languagesale 15% off
Amendment 1 of ISO 1651/1974 concerns cover page and pages 1, 2 and 3. Modify the general title as follows: "Hardmetal (carbide) core tube drawing plugs - Dimensions". On page 1, clause 1, replace the first and second sentences by new ones. Pages 2 and 3: modify each title (clauses 2 and 3) in accordance with the titles given in this amendment.
- Standard2 pagesEnglish languagesale 15% off
- Standard2 pagesFrench languagesale 15% off
- Standard2 pagesFrench languagesale 15% off
Concerns cover page and page 1. Modify the title as follows: "Wire, bar and tube drawing dies with hardmetal (carbide) core - Specifications". Modify the first sentence on page 1 correspondingly.
- Standard1 pageEnglish languagesale 15% off
- Standard1 pageFrench languagesale 15% off
- Standard1 pageFrench languagesale 15% off
Specifies the main dimensions for the certain number of tool types, and the codified designation of dies and the marking. Details not indicated are left to the discretion of the manufacturers or should be specified in national standards. Includes, in annex A, a comparison of several dimensions for various types of drawing dies, and, in annex B, a terminology, in several languages, for characteristic elements.
- Standard15 pagesEnglish languagesale 15% off
- Standard15 pagesFrench languagesale 15% off
- Standard15 pagesFrench languagesale 15% off
Specifies the general dimensions of tube drawing mandrels with respect to their diameter. applies to brazed drawing mandrels and sleeved drawing mandrels. The dimensions have been determined taking existing practice into account as far as possible. Threads are given in both measurement systems (metric and inches) so as to allow the use of these mandrels on any machine.
- Standard3 pagesEnglish languagesale 15% off
- Standard3 pagesFrench languagesale 15% off
- Standard3 pagesFrench languagesale 15% off
This European Standard specifies the general safety requirements for cold rolling mills for flat products. It describes the foreseeable, significant hazards - so far as this is possible for this particular machinery - and indicates possible preventative measures for avoiding the hazards and reducing the risks.
Manufacturers shall perform a risk assessment specific to their machinery, its use and environment (other machinery, buildings etc.) in order to determine which hazards are significant and decide the preventative measures to be taken (see Annex H).
This standard deals with significant hazards, hazardous situations and events relevant to cold rolling mills for flat products. It deals not only with circumstances where the machinery is used as intended, but also includes other conditions foreseen by the manufacturer, such as foreseeable faults, malfunctions or misuse (see clauses 4 and 5).
This standard assumes that the machinery is used with adequate workplace lighting conforming to EN 12464-1 or to local regulations.
This standard applies to: Plant and equipment used for the manufacturing of metal cold rolled flat products from the material entry station, through the forming stations, to the exit
- Standard63 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the general safety requirements for hot rolling mills for flat products. It describes the foreseeable, significant hazards - so far as this is possible for this particular machinery - and indicates possible preventative measures for avoiding the hazards and reducing the risks.
Manufacturers shall perform a risk assessment specific to their machinery, its use and environment (other machinery, buildings etc.) in order to determine which hazards are significant and decide the preventative measures to be taken (see Annex G).
This standard deals with significant hazards, hazardous situations and events relevant to hot rolling mills for flat products. It deals not only with circumstances where the machinery is used as intended, but also includes other conditions foreseen by the manufacturer, such as foreseeable faults, malfunctions or misuse (see clauses 4 and 5).
This standard applies to: Plant and equipment used for the manufacturing of metal hot rolled flat products from the material entry station, the forming stations, to the exit to storage
- Standard60 pagesEnglish languagesale 10% offe-Library read for1 day
This standard specifies the essential safety requirements for injection moulding machines for the processing of plastics and/or rubber.
All hazards listed in Clause 4 are covered by this standard.
The following machines are not covered:
- machines on which the clamping unit can only be operated by the physical force of the operator;
- injection moulding machines with pneumatic drives for the platen movement;
- injection moulding machines with vertical platen movements driven by an electrical axis;
- blow moulding machines associated with an injection process (EN 422);
- machines for reaction injection moulding (RIM) (EN 1612-1);
- presses (EN 289)
- footwear moulding machines covered by EN 1845.
The safety requirements for the interaction between injection moulding machines and ancillary equipment are specified.
This standard covers magnetic clamping systems only if:
- machines have horizontal clamping units; and
- the mould area is protected by guards; and
- such systems are delivered at the same time as the injection moulding machine by the machine manufacturer.
This standard does not cover requirements for the design of an exhaust system.
This standard is not applicable to injection moulding machines which are manufactured before the date of its publication as an EN.
- Standard96 pagesEnglish languagesale 10% offe-Library read for1 day
Deals with the safety of tools which the rated voltage is not more than 250 V for single-phase a.c. or d.c. tools and 440 V for three-phase a.c. tools. Supplements or modifies the corresponding clauses of IEC 60745-1
- Standard12 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard describes the general safety requirements for tube forming and rolling mills and finishing line equipment corresponding to the definition in EN 292-1. It describes the foreseeable, significant hazards, hazardous situations and events for plants and particular machinery, as well their integration into a plant. It indicates possible preventative measures for avoiding the hazards and reducing the risks. It deals not only with circumstances where the machinery is used as intended, but also includes other conditions foreseen by the manufacturer, such as foreseeable faults, malfunctions or misuse (see clauses 4/5).
- Standard48 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard6 pagesEnglish languagesale 15% off
- Standard6 pagesFrench languagesale 15% off