This part of IEC 61757 specifies terminology, characteristic performance parameters, related test and calculation methods, and specific test equipment for interrogation units used in distributed fibre optic acoustic sensing and vibration measurement systems. This document refers to Rayleigh backscatter and phase detection method by phase-sensitive coherent optical time-domain reflectometry (ϕ-OTDR) only. Quasi-static and low frequency operation modes are not covered by this document. Generic specifications for fibre optic sensors are defined in IEC 61757.

  • Standard
    52 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 61757-3-2:2022 specifies the terminology, characteristic performance parameters, related test and calculation methods, as well as specific test equipment for interrogation units used in distributed fibre optic acoustic sensing and vibration measurement systems. This document refers to the Rayleigh backscatter and phase detection method by phase-sensitive coherent optical time-domain reflectometry (ϕ-OTDR) only. Quasi-static and low frequency operation modes are not covered by this document. Generic specifications for fibre optic sensors are defined in IEC 61757.

  • Standard
    98 pages
    English and French language
    sale 15% off

The purpose of this report is to be a guideline for those considering to install a high bandwidth (high bit-rate) FttX-network. After studying the report, operators, communities, energy companies, installers and others will understand the necessary steps to take to plan and install networks with high quality and cost effectiveness, and to secure a uniform structure and a high quality level on such networks.

  • Technical report
    102 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This part of IEC 61757 specifies the terminology, characteristic performance parameters and
related test methods of optical temperature sensors based on fibre Bragg gratings (FBG) that
carry out temperature measurements in the temperature range between –260 °C and 600 °C.
Generic specifications for fibre optic sensors are defined in IEC 61757.

  • Standard
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This part of IEC 60794, which is a generic specification, covers optical fibre ribbons. Requirements which are described in this part apply to optical fibre ribbon cables for use with telecommunication equipment and devices employing similar techniques, in particular optical fibre cables in IEC 60794-2 for indoor use, in IEC 60794-3 for outdoor use, in IEC 60794-4 for self-supporting overhead use, in IEC 60794-5 for air blown use and in IEC 60794-6 for indoor/outdoor use. The detailed specification can be verified in specifications for each application such as IEC 60794-2 and IEC 60794-3.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This part of IEC 61757 defines the terminology, structure, characteristics and their
measurement method including the procedures, for an optical tilt sensor based on fibre Bragg
gratings (FBGs) as the sensitive element.

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 61757-2-1:2021 specifies the terminology, characteristic performance parameters and related test methods of optical temperature sensors based on fibre Bragg gratings (FBG) that carry out temperature measurements in the temperature range between ‑260 °C and 600 °C. Generic specifications for fibre optic sensors are defined in IEC 61757.

  • Standard
    77 pages
    English and French language
    sale 15% off

IEC 61757-5-1:2021 defines the terminology, structure, characteristics and their measurement method including the procedures, for an optical tilt sensor based on fibre Bragg gratings (FBGs) as the sensitive element.

  • Standard
    42 pages
    English and French language
    sale 15% off

IEC 60794-1-31:2021 is available as IEC 60794-1-31:2021 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 60794-1-31:2021 which is a generic specification, covers optical fibre ribbons. Requirements which are described in this part apply to optical fibre ribbon cables for use with telecommunication equipment and devices employing similar techniques, in particular optical fibre cables in IEC 60794-2 for indoor use, in IEC 60794-3 for outdoor use, in IEC 60794-4 for self-supporting overhead use, in IEC 60794-5 for air blown use and in IEC 60794-6 for indoor/outdoor use. The detailed specification can be verified in specifications for each application such as IEC 60794-2 and IEC 60794-3. This second edition cancels and replaces the first edition published in 2018. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
- The geometrical requirements for optical fibre ribbon with typically 250 µm coating diameter have been modified and those for the optical fibre ribbon with typically 200 µm coating diameter have been added.
- "Identification by positional identification" and "Identification by ribbon coding and fibre colouring" are moved to a new informative Annex A.

  • Standard
    28 pages
    English and French language
    sale 15% off

IEC 62134-1:2009 establishes uniform generic requirements for fibre optic closures. This standard does not cover test and measurement procedures, which are described in IEC 61300 series. The main changes with respect to the previous edition are:
- addition and rewording of some terms and definitions;
- reconsideration of type, style and variant in the requirements;
- removal of quality assessment procedures.

  • Standard
    42 pages
    English and French language
    sale 15% off

IEC 62801:2020 specifies a measurement method of half-wavelength voltage applicable to Mach-Zehnder optical modulators in wireless communication and broadcasting systems. In addition, this method is also effective for the estimation of the intermodulation distortion of Mach-Zehnder optical modulators. The method applies for the following:
– frequency range: 10 MHz to 30 GHz;
– wavelength band: 0,8 µm to 2,0 µm;
– electro-optic material based Mach-Zehnder optical modulators and their modules.

  • Standard
    75 pages
    English and French language
    sale 15% off

This part of IEC 61757 defines terminology, structure, and a characteristic test method of an
optical current sensor using the polarimetric method. It addresses the current sensing element
only and not the additional devices that are unique to each application. Generic specifications
for fibre optic sensors are defined in IEC 61757.
As the specifications of optical polarimetric fibre current sensors required by each user vary
depending on the application, this document does not define the required performance values.
The required performance values are defined when designing a sensor according to the specific
application.

  • Standard
    51 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 61757-4-3: 2020 defines terminology, structure, and a characteristic test method of an optical current sensor using the polarimetric method. It addresses the current sensing element only and not the additional devices that are unique to each application. Generic specifications for fibre optic sensors are defined in IEC 61757. As the specifications of optical polarimetric fibre current sensors required by each user vary depending on the application, this document does not define the required performance values. The required performance values are defined when designing a sensor according to the specific application.

  • Standard
    99 pages
    English and French language
    sale 15% off

IEC TR 63099-2:2020 provides information about the current and latest applications for electric-field measurement that use radio-over-fibre technologies. System configurations, specifications, and measurement examples of each electric-field measurement system are included. The theoretical background of electric-field measurement and calibration method of electric-field sensors are beyond the scope of this document.

  • Technical report
    16 pages
    English language
    sale 15% off

IEC 61757-1-1 defines detail specifications for fibre optic sensors using one or morefibre Bragg gratings (FBG) as the sensitive element for strain measurements. Genericspecifications for fibre optic sensors are defined in IEC 61757.This document specifies the most important features and characteristics of a fibre optic sensorfor strain measurements, based on use of an FBG as the sensitive element, and defines theprocedures for their determination. Furthermore, it specifies basic performance parameters andcharacteristics of the corresponding measuring instrument to read out the optical signal fromthe FBG. This document refers to the measurement of static and dynamic strain values in arange of frequencies.A blank detail specification is provided in Annex B.

  • Standard
    57 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 61757-1-1:2020 is available as IEC 61757-1-1:2020 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.
IEC 61757-1-1:2020 defines detail specifications for fibre optic sensors using one or more fibre Bragg gratings (FBG) as the sensitive element for strain measurements. Generic specifications for fibre optic sensors are defined in IEC 61757. This document specifies the most important features and characteristics of a fibre optic sensor for strain measurements, based on use of an FBG as the sensitive element, and defines the procedures for their determination. Furthermore, it specifies basic performance parameters and characteristics of the corresponding measuring instrument to read out the optical signal from the FBG. This document refers to the measurement of static and dynamic strain values in a range of frequencies. A blank detail specification is provided in Annex B. This second edition cancels and replaces the first edition published in 2016. This edition constitutes a technical revision. This edition includes the following technical changes with respect to the previous edition:
- update of cited standards;
- clarification of definitions and test specifications.

  • Standard
    108 pages
    English and French language
    sale 15% off

This European Standard covers street cabinets for up to 1440 fibre connections for use in outside plant environments under category A according to EN 61753-1:Ed2. This document contains the initial, start of life dimensional, optical, mechanical and environmental performance requirements of a fully installed passive optical fibre street cabinet, in order for it to be categorised as an EN standard product. The street cabinet is a housing containing modular fibre management systems with splice trays for various fibre separation levels and connector mounting plates. The street cabinet may contain one or more of the following: storage and/or routing of cable; through-box/uncut fibre, cable storage; connectors passive optical devices.

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document provides general conditions for the standard performance of optical dynamic modules. All performance standards of dynamic modules are based on the general conditions defined in this document. Additional conditions are included in individual performance standards.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 62343-1:2019 provides general conditions for the standard performance of optical dynamic modules. All performance standards of dynamic modules are based on the general conditions defined in this document. Additional conditions are included in individual performance standards. This second edition cancels and replaces the first edition, published in 2016, and constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a) errors of Table 1 has been corrected;
b) the contents of Table A.1 has been revised.
Keywords: standard performance of optical dynamic modules

  • Standard
    17 pages
    English and French language
    sale 15% off

This part of IEC 62149 covers the performance specification for radio-over-fibre (RoF) transceivers used for mobile fronthaul systems. The performance standard contains a definition of the product performance requirements together with a series of tests and measurements with clearly defined conditions, severities, and pass/fail criteria. The tests are intended to be run on a one-off basis to prove any product's ability to satisfy the performance standard's requirements. A product that has been shown to meet all the requirements of a performance standard canbe declared to be in compliance with the performance standard.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 62149-10:2018 covers the performance specification for radio-over-fibre (RoF) transceivers used for mobile fronthaul systems. The performance standard contains a definition of the product performance requirements together with a series of tests and measurements with clearly defined conditions, severities, and pass/fail criteria. The tests are intended to be run on a one-off basis to prove any product's ability to satisfy the performance standard's requirements. A product that has been shown to meet all the requirements of a performance standard can be declared to be in compliance with the performance standard.
Keywords: radio-over-fibre (RoF) transceivers used for mobile fronthaul systems

  • Standard
    36 pages
    English and French language
    sale 15% off

This document is a generic specification covering optical fibres, components and subassemblies
as they pertain specifically to fibre optic sensing applications. It has been
designed to be used as a common working and discussion tool by the vendors of components
and subassemblies intended to be integrated in fibre optic sensors, as well as by designers,
manufacturers and users of fibre optic sensors independent of any application or installation.
The objective of this document is to define, classify and provide the framework for specifying
fibre optic sensors, and their specific components and subassemblies. The requirements of
this document apply to all related fibre optic sensor standards which belong to IEC 61757 (all
parts). Standards of IEC 61757 (all parts) contain requirements specific to sensors for
particular quantities subject to measurement, and for a particular style or variant of such a
fibre optic sensor.

  • Standard
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 61757:2018 is a generic specification covering optical fibres, components and sub-assemblies as they pertain specifically to fibre optic sensing applications. It has been designed to be used as a common working and discussion tool by the vendors of components and subassemblies intended to be integrated in fibre optic sensors, as well as by designers, manufacturers and users of fibre optic sensors independent of any application or installation. The objective of this document is to define, classify and provide the framework for specifying fibre optic sensors, and their specific components and subassemblies. The requirements of this document apply to all related fibre optic sensor standards which belong to IEC 61757 (all parts). Standards of IEC 61757 (all parts) contain requirements specific to sensors for particular quantities subject to measurement, and for a particular style or variant of such a fibre optic sensor. Keywords: fibre optic sensors

  • Standard
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 60794-1-31:2018(E) which is a generic specification, covers optical fibre ribbons. Requirements which are described in this part apply to optical fibre ribbon cables for use with telecommunication equipment and devices employing similar techniques, in particular optical fibre cables in IEC 60794-2 for indoor use and in IEC 60794-3 for outdoor use. Detailed specifications for each application are given in IEC 60794-2 and IEC 60794-3. Keywords: optical fibre ribbons

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 62343-3-4: 2018 provides a performance specification template for multicast optical switches. The object is to provide a framework for the preparation of performance specifications or product specifications of multicast optical switches. Specification parameters required in this document are considered as essential in the product specifications or performance specifications. Keywords: multicast optical switch (MCOS)

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 60794-1-31:2018 which is a generic specification, covers optical fibre ribbons. Requirements which are described in this part apply to optical fibre ribbon cables for use with telecommunication equipment and devices employing similar techniques, in particular optical fibre cables in IEC 60794-2 for indoor use and in IEC 60794-3 for outdoor use. Detailed specifications for each application are given in IEC 60794-2 and IEC 60794-3.
Keywords: optical fibre ribbons

  • Standard
    21 pages
    English and French language
    sale 15% off

IEC 62343-3-4: 2018 provides a performance specification template for multicast optical switches. The object is to provide a framework for the preparation of performance specifications or product specifications of multicast optical switches. Specification parameters required in this document are considered as essential in the product specifications or performance specifications.
Keywords: multicast optical switch (MCOS)

  • Standard
    37 pages
    English and French language
    sale 15% off

IEC 62343-5-2:2018 describes the measurement methods of dynamic crosstalk during port switching for 1 x N fixed-grid wavelength selective switches (WSSs). The objective of this document is to establish a standard test method for different-channel dynamic crosstalk and same-channel dynamic crosstalk that occur when a particular optical channel signal is switched to the specific branching port against a common port in ITU‑T 50 GHz and 100 GHz fixed grid 1 x N (N ≥ 3) WSSs.

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 61757:2018 is a generic specification covering optical fibres, components and sub-assemblies as they pertain specifically to fibre optic sensing applications. It has been designed to be used as a common working and discussion tool by the vendors of components and subassemblies intended to be integrated in fibre optic sensors, as well as by designers, manufacturers and users of fibre optic sensors independent of any application or installation. The objective of this document is to define, classify and provide the framework for specifying fibre optic sensors, and their specific components and subassemblies. The requirements of this document apply to all related fibre optic sensor standards which belong to IEC 61757 (all parts). Standards of IEC 61757 (all parts) contain requirements specific to sensors for particular quantities subject to measurement, and for a particular style or variant of such a fibre optic sensor.
Keywords: fibre optic sensors

  • Standard
    73 pages
    English and French language
    sale 15% off

IEC 62343-5-2:2018 describes the measurement methods of dynamic crosstalk during port switching for 1 x N fixed-grid wavelength selective switches (WSSs). The objective of this document is to establish a standard test method for different-channel dynamic crosstalk and same-channel dynamic crosstalk that occur when a particular optical channel signal is switched to the specific branching port against a common port in ITU‑T 50 GHz and 100 GHz fixed grid 1 x N (N ≥ 3) WSSs.

  • Standard
    42 pages
    English and French language
    sale 15% off

This document specifies measurement methods of a half-wavelength voltage and a chirp
parameter applicable to MZMs in microwave and millimeter-wave RoF systems. In addition,
these methods are also effective for the estimation of the intermodulation distortions and
transmission performances. The methods apply for the following:
– frequency range: 5 GHz to 110 GHz;
– wavelength band: 0,8 μm to 2,0 μm;
– electro-optic material based MZMs and their modules.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This part of IEC 61757 defines detail specifications for distributed temperature measurement
by a fibre optic sensor, also known as fibre optic distributed temperature sensing (DTS). DTS
includes the use of Raman scattering, Brillouin scattering and Rayleigh scattering effects. In
addition, Raman scattering and Rayleigh scattering based measurements are performed with
a single-ended fibre configuration only. Brillouin scattering based measurements are
performed with a single-ended fibre or fibre loop configuration. The technique accessible from
both sides at same time (e. g. Brillouin optical time domain analysis, BOTDA) is referred to
here as a loop configuration. Generic specifications for fibre optic sensors are defined in
IEC 61757-1:2012.
This part of IEC 61757 specifies the most important DTS performance parameters and defines
the procedures for their determination. In addition to the group of performance parameters, a
list of additional parameters has been defined to support the definition of the measurement
specifications and their associated test procedures. The definitions of these additional
parameters are provided for informational purposes and should be included with the sets of
performance parameters.
A general test setup is defined in which all parameters can be gathered through a set of tests.
The specific tests are described within the clause for each measurement parameter. This
general test setup is depicted and described in Clause 4 along with a list of general
information that should be documented based upon the specific DTS instrument and test
setup used to measure these parameters as per IEC 61757-2-2.
Annex A provides a blank performance parameter table which should be used to record the
performance parameter values for a given DTS instrument and chosen optical test setup
configuration.
Annex B provides guidelines for optional determination of point defect effects.

  • Standard
    34 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 62343:2017(E) applies to all commercially available optical dynamic modules and devices. It describes the products covered by the IEC 62343 series, defines terminology, fundamental considerations and basic approaches. The object of this document is to: establish uniform requirements for operation, reliability and environmental properties of dynamic modules (DMs) to be implemented in the appropriate DM standard, and provide assistance to the purchaser in the selection of consistently high-quality DM products for his particular applications, as well as in the consultation of the appropriate specific DM standard(s). This document covers performance templates, performance standards, reliability qualification requirements, hardware and software interfaces and related testing methods. Since a dynamic module integrates an optical module/device, printed wiring board, and software/firmware, the standards developed in the series will mimic appropriate existing standards. On the other hand, since "dynamic module" is a relatively new product category, the dynamic module standards series will not be bounded by the existing practices where requirements differ. The safety standards as related to dynamic modules are mostly optical power considerations, which is covered by IEC TC 76: Optical radiation safety and laser equipment. This second edition cancels and replaces the first edition published in 2013. This edition constitutes a technical revision. This edition includes the following significant technical change with respect to the previous edition: the inclusion of definitions for the wavelength selective switch.

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 61757-2-2:2016(E) defines detail specifications for distributed temperature measurement by a fibre optic sensor, also known as fibre optic distributed temperature sensing (DTS). DTS includes the use of Raman scattering, Brillouin scattering and Rayleigh scattering effects. In addition, Raman scattering and Rayleigh scattering based measurements are performed with a single-ended fibre configuration only. Brillouin scattering based measurements are performed with a single-ended fibre or fibre loop configuration. The technique accessible from both sides at same time (e. g. Brillouin optical time domain analysis, BOTDA) is referred to here as a loop configuration. Generic specifications for fibre optic sensors are defined in IEC 61757-1:2012. This part of IEC 61757 specifies the most important DTS performance parameters and defines the procedures for their determination. In addition to the group of performance parameters, a list of additional parameters has been defined to support the definition of the measurement specifications and their associated test procedures. The definitions of these additional parameters are provided for informational purposes and should be included with the sets of performance parameters. A general test setup is defined in which all parameters can be gathered through a set of tests. The specific tests are described within the clause for each measurement parameter. This general test setup is depicted and described in Clause 4 along with a list of general information that should be documented based upon the specific DTS instrument and test setup used to measure these parameters as per IEC 61757-2-2. Annex A provides a blank performance parameter table which should be used to record the performance parameter values for a given DTS instrument and chosen optical test setup configuration. Annex B provides guidelines for optional determination of point defect effects. Keywords: fibre optic distributed temperature sensing (DTS) This publication is to be read in conjunction with IEC 61757-1:2012

  • Standard
    34 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 63098-1:2017(E) provides information on the current and latest applications of radio-over-fibre technology. Wireless communication, broadcasting, and airport multilateration systems, which are already implemented or will be in the near future, are introduced. This document includes the basic concept, a brief outline and related standards of the applications of RoF technology.

  • Technical report
    21 pages
    English language
    sale 15% off

IEC TR 63099-1:2017(E) provides information about the current and latest applications for antenna measurement that use radio-over-fibre technologies. Antenna gain and the antenna radiation pattern measurement system are covered, which are practically in use and will be used soon. Basic concepts, system configurations and measurement examples of the systems are included.

  • Technical report
    25 pages
    English language
    sale 15% off

IEC 62802:2017 specifies measurement methods of a half-wavelength voltage and a chirp parameter applicable to MZMs in microwave and millimeter-wave RoF systems. In addition, these methods are also effective for the estimation of the intermodulation distortions and transmission performances. The methods apply for the following:
- frequency range: 5 GHz to 110 GHz;
- wavelength band: 0,8 µm to 2,0 µm;
- electro-optic material based MZMs and their modules.

  • Standard
    44 pages
    English and French language
    sale 15% off

IEC 62683-1:2017 establishes the reference dictionary of the general description of low-voltage switchgear and controlgear classes based on defined properties.
This dictionary is used to facilitate the exchange in electronic format of data describing low-voltage switchgear and controlgear.
This document provides clear and unambiguous definitions of a limited number of properties and classes which are mainly used for presentation, selection and identification of products particularly in electronic catalogues.
Each property has an unambiguously defined meaning and naming, and, where relevant, a defined value list, a defined format and a defined unit.
The intention is not to cover manufacturer-specific features.

  • Standard
    277 pages
    English and French language
    sale 15% off

IEC 62343:2017 applies to all commercially available optical dynamic modules and devices. It describes the products covered by the IEC 62343 series, defines terminology, fundamental considerations and basic approaches. The object of this document is to: establish uniform requirements for operation, reliability and environmental properties of dynamic modules (DMs) to be implemented in the appropriate DM standard, and provide assistance to the purchaser in the selection of consistently high-quality DM products for his particular applications, as well as in the consultation of the appropriate specific DM standard(s). This document covers performance templates, performance standards, reliability qualification requirements, hardware and software interfaces and related testing methods. Since a dynamic module integrates an optical module/device, printed wiring board, and software/firmware, the standards developed in the series will mimic appropriate existing standards. On the other hand, since "dynamic module" is a relatively new product category, the dynamic module standards series will not be bounded by the existing practices where requirements differ. The safety standards as related to dynamic modules are mostly optical power considerations, which is covered by IEC TC 76: Optical radiation safety and laser equipment. This second edition cancels and replaces the first edition published in 2013. This edition constitutes a technical revision. This edition includes the following significant technical change with respect to the previous edition: the inclusion of definitions for the wavelength selective switch.

  • Standard
    24 pages
    English language
    sale 15% off
  • Standard
    50 pages
    English and French language
    sale 15% off

IEC TR 63072-1:2017(E) which is a Technical Report, provides an introduction to photonic integrated circuits (PICs) and describes a roadmap for the standardization of PIC technology over the next decade.

  • Technical report
    46 pages
    English language
    sale 15% off

This part of IEC 61757 defines detail specifications for fibre optic sensors using one or more
fibre Bragg gratings (FBG) as the sensitive element for strain measurements. Generic
specifications for fibre optic sensors are defined in IEC 61757-1:2012.
This standard specifies the most important features and characteristics of a fibre optic sensor
for strain measurements based on use of an FBG as the sensitive element, and defines the
procedures for their determination. Furthermore, it specifies basic performance parameters
and characteristics of the corresponding measuring instrument to read out the optical signal
from the FBG. This standard refers to the measurement of static and dynamic strain values in
a range of frequencies.
A blank detail specification is provided in Annex B.

  • Standard
    53 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC TR 62343-6-10:2017(E) which is a Technical Report, discusses the rationale, conceptual definition, and minimum list of functions for an intermediate controller that delivers a dynamic control signal to multiple dynamic modules. These modules are included in an optical-switch-based network node, according to the upper layer controller of software-defined optical networking.

  • Technical report
    15 pages
    English language
    sale 15% off

IEC 61757-1-1:2016(E) defines detail specifications for fibre optic sensors using one or more fibre Bragg gratings (FBG) as the sensitive element for strain measurements. Generic specifications for fibre optic sensors are defined in IEC 61757-1:2012. This standard specifies the most important features and characteristics of a fibre optic sensor for strain measurements based on use of an FBG as the sensitive element, and defines the procedures for their determination. Furthermore, it specifies basic performance parameters and characteristics of the corresponding measuring instrument to read out the optical signal from the FBG. This standard refers to the measurement of static and dynamic strain values in a range of frequencies. A blank detail specification is provided in Annex B. Keywords: Bragg gratings (FBG), strain measurement of fibre optic sensors This publication is to be read in conjunction with IEC 61757-1:2012.

  • Standard
    53 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC TR 62343-6-4:2017(E) which is a Technical Report on reconfigurable optical add/drop multiplexers (ROADMs), provides a description of the ROADMs in dynamic optical networks and related optical component and module technologies, including wavelength selective switches (WSSs).

  • Technical report
    28 pages
    English language
    sale 15% off

IEC 62343-3-2:2016(E) provides a performance specification template for optical channel monitors. The objective of this performance specification template is to provide a framework for the performance specification of the optical channel monitor. Additional specification parameters may be included for detailed product specifications or performance specifications. However, specification parameters specified in this document should not be removed from the detail product specifications or performance specifications. This document outlines the parameters that are used to specify the performance of the optical channel monitor. Keywords: optical channel monitor (OCM)

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 61757-2-2:2016 defines detail specifications for distributed temperature measurement by a fibre optic sensor, also known as fibre optic distributed temperature sensing (DTS). DTS includes the use of Raman scattering, Brillouin scattering and Rayleigh scattering effects. In addition, Raman scattering and Rayleigh scattering based measurements are performed with a single-ended fibre configuration only. Brillouin scattering based measurements are performed with a single-ended fibre or fibre loop configuration. The technique accessible from both sides at same time (e. g. Brillouin optical time domain analysis, BOTDA) is referred to here as a loop configuration. Generic specifications for fibre optic sensors are defined in IEC 61757-1:2012. This part of IEC 61757 specifies the most important DTS performance parameters and defines the procedures for their determination. In addition to the group of performance parameters, a list of additional parameters has been defined to support the definition of the measurement specifications and their associated test procedures. The definitions of these additional parameters are provided for informational purposes and should be included with the sets of performance parameters. A general test setup is defined in which all parameters can be gathered through a set of tests. The specific tests are described within the clause for each measurement parameter. This general test setup is depicted and described in Clause 4 along with a list of general information that should be documented based upon the specific DTS instrument and test setup used to measure these parameters as per IEC 61757-2-2. Annex A provides a blank performance parameter table which should be used to record the performance parameter values for a given DTS instrument and chosen optical test setup configuration. Annex B provides guidelines for optional determination of point defect effects. Keywords: fibre optic distributed temperature sensing (DTS)
This publication is to be read in conjunction with IEC 61757-1:2012

  • Standard
    31 pages
    English language
    sale 15% off
  • Standard
    65 pages
    English and French language
    sale 15% off

IEC 62343-3-2:2016 provides a performance specification template for optical channel monitors. The objective of this performance specification template is to provide a framework for the performance specification of the optical channel monitor. Additional specification parameters may be included for detailed product specifications or performance specifications. However, specification parameters specified in this document should not be removed from the detail product specifications or performance specifications. This document outlines the parameters that are used to specify the performance of the optical channel monitor. Keywords: optical channel monitor (OCM)

  • Standard
    12 pages
    English language
    sale 15% off
  • Standard
    25 pages
    English and French language
    sale 15% off

IEC 62572-3:2016(E) deals with reliability assessment of laser modules used for telecommunication. The aim of this standard is to establish a standard method of assessing the reliability of laser modules in order to minimize risks and to promote product development and reliability and to establish means by which the distribution of failures with time can be determined. This should enable the determination of equipment failure rates for specified end of life criteria. In addition, guidance is given in IEC TR 62572-2. This third edition cancels and replaces the second edition published in 2014. This third edition constitutes a technical revision in which errors in Table 1 and Table 2 have been corrected.

  • Standard
    43 pages
    English and French language
    sale 15% off

1.1 Product definition This European Standard specifies the dimensional, optical, mechanical and environmental performance requirements of a Terminal Equipment Boxes for the FTTX networks. The Terminal Equipment Box will house the ONT/CPE (electronics) and it protects the optical fibres, splices and connectors from direct contact with the user. Optionally it can contain the network test interface, the power supply and the batteries. The performance of the electronics, power supply or batteries are not part of this document. These are covered by another EN document, EN 50700. This specification contains the initial, start of life optical, mechanical and environmental performance requirements of the optical fibre termination in a Terminal Equipment Box, in order for it to be categorized as an EN standard product. 1.2 Operating environment The tests selected combined with the severity and duration is representative of indoor and outside plant for above ground environments defined by: EN 61753-1 Category C Controlled environment 1.3 Reliability Whilst the anticipated service life expectancy of the product in this environment is 20 years, compliance with this specification does not guarantee the reliability of the product. This should be predicted using a recognised reliability assessment programme. 1.4 Quality assurance Compliance with this specification does not guarantee the manufacturing consistency of the product. This should be maintained using a recognised quality assurance programme. 1.5 Allowed fibre and cable types All EN 60793-2-50 fibres can be stored in the Terminal Equipment Box with a minimum storage radius of 20 mm (up to a length of maximum 2 m). Smaller storage radii down to 15 mm are possible with the EN 60793-2-50 B6A fibre types, but in this case the reduction in mechanical reliability should be taken into account (see Annex A).

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC TR 62343-6-9:2015(E) which is a Technical Report, describes a study of the impact of WSS dynamic crosstalk on the optical network and includes dynamic crosstalk measurement examples for three types of WSS. The generating mechanism and the generation factor of dynamic crosstalk in WSS are clarified, and the evaluation of same-channel crosstalk and different-channel crosstalk is shown to be necessary. Keywords: WSS, wavelength selective switch

  • Technical report
    22 pages
    English language
    sale 15% off