This document gives guidance on
a)       confidentiality of personal information for the customer and the laboratory,
b)       laboratory safety requirements,
c)        calibration sources and calibration dose ranges useful for establishing the reference dose-response curves that contribute to the dose estimation from CBMN assay yields and the detection limit,
d)       performance of blood collection, culturing, harvesting, and sample preparation for CBMN assay scoring,
e)       scoring criteria,
f)         conversion of micronucleus frequency in BNCs into an estimate of absorbed dose,
g)       reporting of results,
h)       quality assurance and quality control, and
i)         informative annexes containing sample instructions for customers, sample questionnaire, a microscope scoring data sheet, and a sample report.
This document excludes methods for automated scoring of CBMN.

  • Standard
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document provides terms and definitions for micro process engineering and microfluidics applied in medical and veterinary diagnostics, chemistry, agriculture, pharmacy, biotechnology and the agrifood industry, as well as other application areas.

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This part of IEC 61010 specifies safety requirements for hand-held and hand-manipulated probe
assemblies for electrical test and measurement, and their related accessories. These probe
assemblies are for non-contact or direct electrical connection between a part and electrical test
and measurement equipment. They can be fixed to the equipment or be detachable accessories
for the equipment.
This group safety publication focusing on safety essential requirements is primarily intended to
be used as a product safety standard for the products mentioned in the scope, but is also
intended to be used by technical committees in the preparation of publications for products
similar to those mentioned in the scope of this group safety publication, in accordance with the
principles laid down in IEC Guide 104 and lSO/lEC Guide 51.
One of the responsibilities of a technical committee is, wherever applicable, to make use of
basic safety publications and/or group safety publications in the preparation of its publications.

  • Standard
    103 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 61010-2-030:2023 specifies safety requirements for equipment having testing or measuring circuits which are connected for test or measurement purposes to devices or circuits outside the measurement equipment itself. These include measuring circuits which are part of electrical test and measurement equipment, laboratory equipment, or process control equipment. These circuits in equipment have additional protective means between the circuit and an operator. This third edition cancels and replaces the second edition published in 2017. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a) in 1.2.1, requirements for protection against hazards which could occur from reading a voltage have been added to the scope;
b) Clause 2, all normative references have been dated and new normative references have been added;
c) in 4.3.2.5, requirements for power supply have been modified;
d) in 4.3.2.6, requirements for inputs/outputs have been modified;
e) in 4.4.2.101, a new subclause about surge protective devices has been added;
f) in 5.1.5.101.2, minimum ratings for voltage of measuring terminals are required;
g) Subclause 6.6.101 modifies 6.6.101 and 6.6.102 of previous edition:
1) in 6.6.101.1, insulating material of group I may be allowed for determination of creepage distances of measuring circuit terminals;
2) In 6.6.101.2, clearances and creepage distances up to 3 000 V for measuring circuit terminals in unmated position have been defined;
3) in 6.6.101.3, requirements for measuring circuit terminals in partially mated position have been specified;
4) in 6.6.101.4, requirements for measuring circuit terminals in mated position have been specified;
5) Subclause 6.6.101.5 replaces 6.6.102;
h) Subclause 9.101 to consider the protection of measuring circuits against the spread of fire and arc flash has been added and Table 102 has been replaced by Table K.101;
i) in 9.101.2, relocation of 101.3 of previous edition;
j) in 9.101.3, relocation of 101.4 of previous edition, extension to measurement category II and reference to IEC 61000-4-5 for tests;
k) in 14.101, relocation of 14.102 and 14.101 of previous edition has been removed;
l) in 101.3, relocation of 101.5 of previous edition, and more requirements added against hazard occurring from reading a voltage value;
m) in K.2.1, another method for determination of clearances of secondary circuits is proposed;
n) in K.3.2, new Table K.15 and Table K.16 for clearance calculation;
o) in K.101.4.1, new Table K.103 and Table K.104 replace Table K.102, Table K.103 and Table K.104;
p) in K.101.4, the subclause has been reviewed; Tables and tests for solid insulation have been modified; Table K.105 replaces Table K.9;
q) Table K.101, replacement of Table K.106;
r) Clause K.4, redraft of the clause to propose a method for determination of Ut for circuits which reduce transient overvoltages;
s) Annex AA: Figure AA.1 has been redesigned;
t) Annex EE: addition of a new informative annex for determination of clearances for Table 101.
It has the status of a group safety publication in accordance with IEC Guide 104.

  • Standard
    300 pages
    English language
    sale 15% off
  • Standard
    108 pages
    English and French language
    sale 15% off

IEC 61010-2-033:2023 specifies safety requirements for hand-held multimeters and other meters for domestic and professional use, capable of measuring mains. Hand-held multimeters are multi-range multifunction measuring instruments intended to measure voltage and other electrical quantities such as resistance or current. Their primary purpose is to measure voltage on a live mains. They are suitable to be supported by one hand during normal use. This third edition cancels and replaces the second edition published in 2019. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a) Clause 2, all normative references have been dated and new normative references have been added;
b) 4.4.2.101 is a new subclause about surge protective devices;
c) Subclause 6.6.101 modifies 6.6.101 and 6.6.102 of previous edition:
1) in 6.6.101.1, insulating material of group I may be allowed for determination of creepage distances of measuring circuit terminals;
2) in 6.6.101.2, Clearances and creepage distances up to 3 000 V for measuring circuit terminals in unmated position have been defined;
3) in 6.6.101.3, requirements for measuring circuit terminals in partially mated position have been specified;
4) in 6.6.101.4, requirements for measuring circuit terminals in mated position have been specified;
5) Subclause 6.6.101.5 replaces 6.6.102;
d) Subclause 6.101 replaces 6.9.101 of the previous edition with modifications;
e) 9.101 is a new subclause to consider the protection of measuring circuits against the spread of fire and arc flash;
f) in 9.101.2, relocation of 101.3 of previous edition;
g) in 9.101.3, relocation of 101.4 of previous edition;
h) in 101.3, relocation of Clause 102 of previous edition;
i) in K.2.1, another method for determination of clearances of secondary circuits is proposed;
j) in K.3.2, new Table K.15 and Table K.16 for clearance calculation;
k) Clause K.4 of the previous edition has been deleted;
l) Subclause K.101.4 has been reviewed;
m) Table K.104 of the previous edition has been deleted;
n) Annex AA: Figure AA.1 has been redesigned;
o) Annex EE: addition of a new informative annex for determination of clearances for the purposes of Table 101.

  • Standard
    285 pages
    English language
    sale 15% off
  • Standard
    100 pages
    English and French language
    sale 15% off

This document provides terms and definitions for micro process engineering and microfluidics applied in medical and veterinary diagnostics, chemistry, agriculture, pharmacy, biotechnology and the agrifood industry, as well as other application areas.

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document provides terms and definitions for micro process engineering and microfluidics applied in medical and veterinary diagnostics, chemistry, agriculture, pharmacy, biotechnology and the agrifood industry, as well as other application areas.

  • Standard
    16 pages
    English language
    sale 15% off
  • Standard
    16 pages
    French language
    sale 15% off

This European Standard is a product specification, giving performance requirements for fire safety cabinets to be used for the storage of flammable liquids. It is applicable to cabinets with a total internal volume of not greater than 2 m³, which may be free standing, restrained to a wall or mounted on plinth or castors.
It is not applicable to brick enclosures or walk-in storage rooms.
This Standard does not apply to any support frame or mechanism other than the base which is integral to the cabinet.
Requirements are given in respect of the construction of the cabinet and its capacity to resist fire conditions on the outside. A classification of cabinets is given, according to the level of fire resistance offered, and a type test is included, see Annex A.
The tests described in this European Standard are type tests.
This European Standard does not discriminate between different flammable liquids, which may have considerably different physical properties.
Attention is drawn to national regulations, which may apply with regards to the storage of flammable liquids.

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 61010-2-034:2023 specifies safety requirements to equipment for measuring insulation resistance and to equipment for testing electric strength which have an output voltage exceeding 50 V a.c. or 120 V d.c. This document also applies to combined measuring equipment which has an insulation resistance measurement function or an electric strength test measurement function. This document has the status of a horizontal publication in accordance with IEC Guide 108. It has the status of a group safety publication in accordance with IEC Guide 104. This second edition cancels and replaces the first edition published in 2017. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a) in 1.2.1, requirements for protection against hazards which could occur from reading a voltage have been added to the scope;
b) Clause 2, all normative references have been dated; new normative references have been added;
c) in 4.3.2.5, requirements for power supply have been modified;
d) in 4.3.2.6, requirements for inputs/outputs have been modified;
e) in 5.1.5.101.2, minimum ratings for voltage of measuring terminals are required;
f) in 5.4.2, new ratings for documentation have been added;
g) in 5.4.4, new instructions for operation have been added;
h) in 5.101.1, hazard indicators shall be functional in normal condition and in single fault condition;
i) in 6.6.101.1, insulating material of group I may be allowed for determination of creepage distances of measuring circuit terminals;
j) in 6.6.101.2, Clearances and creepage distances above 1 000 V a.c. and 1 500 V d.c. for measuring circuit terminals in unmated position have been defined;
k) in 6.6.101.3, requirements for measuring circuit terminals in partially mated position have been specified;
l) in 6.6.101.4, requirements for measuring circuit terminals in mated position have been specified;
m) Subclause 6.102 replaces 6.9.103 and has been rephrased;
n) new Subclause 9.101 to consider the protection of measuring circuits against the spread of fire and arc flash has been added. Table 102 has been replaced by Table K.101;
o) In 9.101.2, relocation of 101.3 of previous edition;
p) In 9.101.3, relocation of 101.4 of previous edition, extension to measurement category II and reference to IEC 61000-4-5 for tests;
q) in 9.101.4, requirements for measuring circuit terminals in mated position have been specified;
r) in 9.101.5, relocation of K.103 of previous edition with numerous technical changes;
s) in 14.101, relocation of 14.102. 14.101 of previous edition has been removed;
t) in 101.3, relocation of 101.5 of previous edition, and more requirements added against hazard occurring from reading a voltage value;
u) in K.2.1, another method for determination of clearances of secondary circuits is proposed;
v) in K.3.2, new Table K.15 and Table K.16 for clearance calculation;
w) in K.3.101, relocation of 6.9.104 of previous edition;
x) in K.101.4.1, new Table K.103 and Table K.104 replace Table K.102, Table K.103 and Table K.104;
y) in K.101.4, the subclause has been reviewed. Tables and tests for solid insulation have been modified. Table K.105 replaces Table K.9;
z) Table K.101, replacement of Table K.106;
aa) Clause K.4, redraft of the clause to propose a method for determination of Ut for circuits which reduce transient overvoltages;
bb) Annex EE: addition of a new informative annex for determination of clearances for Table 101.

  • Standard
    323 pages
    English language
    sale 15% off
  • Standard
    123 pages
    English and French language
    sale 15% off

This document is a product specification, giving performance requirements for fire safety storage cabinets to be used for the storage of flammable liquids. It is applicable to cabinets with a total internal volume of not greater than 2 m3, which can be free standing, restrained to a wall or mounted on plinth or castors.
This document does not apply to brick enclosures or walk-in storage rooms.
This document does not apply to any support frame or mechanism other than the base which is integral to the fire safety storage cabinet.
Requirements are given in respect of the construction of the fire safety storage cabinet and its capacity to resist fire conditions on the outside. A classification of fire safety storage cabinets is given, according to the level of fire resistance offered, and a type test is included, see Annex A.
The tests described in this document are type tests.
This document does not discriminate between different flammable liquids, which can have considerably different physical properties.
Attention is drawn to national regulations, which can apply with regard to the storage of flammable liquids.

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the characteristics of fume cupboards, as defined in EN 14175-1, for work with unsealed radioactive materials with specific requirements regarding radiation protection. It does not apply to fume cupboards, glove boxes or hot cells (shielded radiation containment cells which can incorporate fume extraction).
The purpose of this document is to set out rules for the design and testing of fume cupboards for work with unsealed radioactive materials, in order to provide guidelines for the manufacturer, planner, installer, operator, assessor and the authorities.
This document only covers bench type fume cupboards.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document applies to an articulated extraction arm used as a local exhaust device in laboratories and comprised of a capture device (receiving, enclosing or capture hood, nozzle or flat screen) connected to an extraction arm which is articulated ducting to move air from the capture device to discharge.
This standard specifies:
- a method for type testing;
- a method to assess the three-dimensional capture zone of local exhaust devices mounted on an articulated extract arm;
- a method for assessing the emission release capture efficiency of local exhaust devices connected to an articulated extract arm and its robustness to a challenge of air disturbance directly in front of and in close proximity to the capture hood and release source;
- a method for establishing the reachable, three-dimensional workspace of local exhaust devices mounted on an articulated extract arm by measuring the possible positions of the opening of the device;
- a method for measuring the pressure drop and noise level in the type test;
- instructions for marking the device and recommended content of information for use;
- guidance for use describing the limitations of local exhaust devices with articulated extract arm for different airflow rates establishing the capture zone;
- guidance on selection, installation, commissioning, and control testing of articulated extract arms and their local exhaust ventilation systems.
The scope does not include filtration requirements and impact of fully or partly recirculation of the airflow extracted by an articulated extract arm.

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document applies to an articulated extraction arm used as a local exhaust device in laboratories and comprised of a capture device (receiving, enclosing or capture hood, nozzle or flat screen) connected to an extraction arm which is articulated ducting to move air from the capture device to discharge.
This standard specifies:
- a method for type testing;
- a method to assess the three-dimensional capture zone of local exhaust devices mounted on an articulated extract arm;
- a method for assessing the emission release capture efficiency of local exhaust devices connected to an articulated extract arm and its robustness to a challenge of air disturbance directly in front of and in close proximity to the capture hood and release source;
- a method for establishing the reachable, three-dimensional workspace of local exhaust devices mounted on an articulated extract arm by measuring the possible positions of the opening of the device;
- a method for measuring the pressure drop and noise level in the type test;
- instructions for marking the device and recommended content of information for use;
- guidance for use describing the limitations of local exhaust devices with articulated extract arm for different airflow rates establishing the capture zone;
- guidance on selection, installation, commissioning, and control testing of articulated extract arms and their local exhaust ventilation systems.
The scope does not include filtration requirements and impact of fully or partly recirculation of the airflow extracted by an articulated extract arm.

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day

The scope of the Amendment is the same as EN 61010-2-101:2017. It applies to equipment intended for in vitro diagnostic (IVD) medical purposes, including self-test IVD medical purposes.

  • Amendment
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This standard EN 61010-2-101:2017 Safety requirements for electrical equipment for measurement, control and laboratory use is classified in these ICS categories:
19.080 Electrical and electronic testing
71.040.10 Chemical laboratories. Laboratory equipment
11.040.55 Diagnostic equipment
IEC 61010-2-101:2015 is available as IEC 61010-2-101:2015 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.
IEC 61010-2-101:2015 applies to equipment intended for in vitro diagnostic (IVD) medical purposes, including self-test IVD medical purposes. It has the status of a group safety function, as specified in IEC Guide 104. This standard has been prepared in close collaboration with Working Group CENELEC BTTF 88.1. This second edition cancels and replaces the first edition published in 2002. It constitutes a technical revision and includes the following significant changes from the first edition, as well as numerous other changes:
- excluded IEC 61010-2-081 (general laboratory equipment) from the scope. This separates IEC 61010-2-081 and IEC 61010-2-101 equipment;
- updated Biohazard and Lot symbols in Table 1 in Clause 5;
- added requirement for within expiration consumables and authorized representative details in Instructions for Use to Clause 5;
- added requirement for gas or liquid markings and ratings to Clause 5;
- added requirement to include OPERATOR instructions to deal with consumable or sample spills, jams or breakage inside equipment, disposal of hazardous waste, personal protection, RISK reduction procedures relating to flammable liquids, burns from surfaces, and loading and unloading of sample and reagents in Instructions for Use to Clause 5;
- added requirement for manufacturer to provide instructions on equipment transport, storage and removal from use to Clause 5;
- added normative reference ISO 18113-5 for instructions for use of self-test IVD medical equipment in Clause 5;
- added requirement for OPERATOR maintenance instructions to Clause 7;
- added requirements for sample zones and loading zones to Clause 7;
- excluded equipment whose size and weight make unintentional movement unlikely from drop test in Clause 8;
- added requirement for biohazard marking to Clause 13;
- added requirement for interlock systems containing electric/electronic or programmable components to Clause 15;
- added informative reference to Usability standard IEC 62366 to Clause 16;
- replaced Clause 17 with requirements of ISO 14971 for RISK assessment.
- Annex BB Instructions for use for self-testing IVD Medical Equipment deleted and a reference given to ISO 18113-5 in Clause 5.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies requirements and recommendations for organizations directly or indirectly involved in the cannabis supply chain, to enable them to: — plan, implement, operate, maintain and update a good production practice programme for providing products that are safe, according to their intended use; — demonstrate compliance with applicable statutory and regulatory requirements; — evaluate and assess mutually agreed customer requirements and demonstrate conformity to them; — effectively communicate with interested parties and demonstrate conformity to relevant interested parties; — demonstrate conformity to stated policies in a cannabis quality programme (CQP) for product safety, product quality, product security and facility safety; — support the evaluation of quality programmes by external organizations or to permit self-assessment or self-declaration of adherence to some or all of the guidance contained in this document. All requirements in this document are generic and intended to be applicable to all organizations in the cannabis supply chain, regardless of size and/or complexity. Organizations that are directly or indirectly involved include (but are not limited to) growers/cultivators, harvesters, primary processors, producers of cannabis, manufacturers of cannabis derivatives, cannabis edibles and/or cannabis products, testing providers, retailers and organizations providing transportation, storage and distribution services, suppliers of equipment, packaging materials and other contact materials. This document intended to enable any organization, including small and/or less developed organizations, to implement externally developed elements in its CQP. NOTE 1 Organizations in the cannabis supply chain are diverse in nature and not all the requirements specified in this document apply to each establishment or process. Justifications for exclusions or the use of alternative measures can be documented by a risk assessment/hazard analysis or other appropriate means. This document provides guidance related to the following categories of cannabis, cannabis derivatives and cannabis products: — cannabis plant seeds; — cannabis plants; — fresh cannabis; — dried cannabis; — cannabis derivatives; — cannabis topicals; — inhalable cannabis. NOTE 2 Annex B provides additional guidance on applying GPP to cannabis edibles with respect to requirements and recommendations in existing food safety standards. Where buildings or premises combine cultivation and processing of cannabis plants, including ancillary activities, along with other operational activities, the requirements and recommendations in this document apply only to that portion of the facility. NOTE 3 Where joint use activities are present in a common building, specific statutory and regulatory requirements can apply for each category. This document does not address the following: — requirements related to research and development activities for finished products; — general fire prevention or building construction features that are normally a function of local building and fire codes where applicable; — premises used exclusively for operational activities, such as office space, call centres and retail outlets, used for the distribution, marketing, or sale of cannabis; NOTE 4 Shipping and receiving of products from the production facility for further distribution are not considered as a retail outlet. — the safe consumption or use of the cannabis or cannabis products produced by organizations applying these good production practices; — occupational health and safety requirements governing cannabis workers and personnel except as identified in A.8.4 and A.8.6; — the protection of the environment; — security of the supply chain monitoring system, including cybersecurity and notifications; NOTE 5 Security and monitoring of the supply chain are dealt with specifically in IWA 37-2. — outdoor cultivation of cannabis and industrial hemp; — gr

  • Standardization document
    66 pages
    English language
    sale 15% off

This document specifies fume cupboards for work with unsealed radioactive materials with specific requirements regarding radiation protection and it does not apply to glove boxes or hot cells not even to α emitting radioisotopes.
The purpose of this document is to set out rules for the design and testing of fume cupboards for work with unsealed radioactive materials, in order to provide guidelines for the planner, installer, operator, assessor and the authorities.
NOTE   If, when handling unsealed radioactive substances, radiopharmaceuticals are produced for use on humans, the fume cupboards covered by this document are not sufficient.
Before using radioactive materials, a safety assessment needs to be performed. To find the maximum activity allowed for every activity with radioactive material it is necessary to take into account the three principles of radiological protection, namely justification, optimization, and the application of dose limits, clarifying how they apply to radiation sources delivering exposure and to individuals receiving exposure. Shield and abatement system required are also evaluated.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day

1 Scope and object
This clause of Part 1 is applicable except as follows:
1.1.1 Equipment included in scope
Replacement:
Replace the first paragraph by the following:
This group safety publication is primarily intended to be used as a product safety standard for
the products mentioned in the scope, but shall also be used by technical committees in the
preparation of their publications for products similar to those mentioned in the scope of this
standard, in accordance with the principles laid down in IEC Guide 104 and lSO/lEC Guide 51.
This Part 2 of IEC 61010 specifies safety requirements for electrical equipment and their
accessories within the categories a) through c), wherever they are intended to be used,
whenever that equipment incorporates one or more of the following characteristics:
– A REFRIGERATING SYSTEM that is acted on or impacted by an integral heating function such
that the combined heating and cooling system generates additional and/or more severe
HAZARDS than those for the two systems if treated separately.
– The materials being treated in the intended application introduce significant heat into the
REFRIGERATING SYSTEM that the cooling system in the application yield additional and/or
more severe HAZARDS than those for the cooling system if operated at the maximum RATED
ambient alone.
– An irradiation function for the materials being treated presenting additional HAZARDS.
– A function to expose the materials being treated to excessive humidity, carbon dioxide,
salt mist, or other substances which may result in additional HAZARDS.
– A function of MECHANICAL MOVEMENT presenting additional HAZARDS.
– Provision for an OPERATOR to walk-in to the operating area to load or unload the materials
being treated.

  • Amendment
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This part of IEC 61010 specifies safety requirements for electrical equipment and its
accessories within the categories a) through c), wherever it is intended to be used, whenever
that equipment incorporates one or more of the following characteristics:
– A REFRIGERATING SYSTEM that is acted on or impacted by an integral heating function such
that the combined heating and REFRIGERATING SYSTEM generates additional and/or more
severe HAZARDS than those for the two systems if treated separately.
– The materials being treated in the intended application introduce significant heat into the
REFRIGERATING SYSTEM, so that the REFRIGERATING SYSTEM in the application yields
additional and/or more severe HAZARDS than those for the REFRIGERATING SYSTEM if
operated at the maximum RATED ambient temperature alone.
– An irradiation function for the materials being treated presenting additional HAZARDS.
– A function to expose the materials being treated to excessive humidity, carbon dioxide,
salt mist, or other substances which can result in additional HAZARDS.
– A function of MECHANICAL MOVEMENT presenting additional HAZARDS.
– Provision for an OPERATOR to walk in to the operating area to load or unload the materials
being treated

  • Standard
    89 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This part of IEC 61010 specifies safety requirements for electrical equipment intended for
sterilization, washing, and disinfection of medical materials in the medical, veterinary,
pharmaceutical and laboratory fields, when used under the environmental conditions of 1.4.
Examples of such equipment include the following:
a) STERILIZERS and disinfectors using steam and/or hot water as the sterilant;
b) STERILIZERS and disinfectors using toxic gas, toxic aerosol or toxic vapour as the sterilant;
c) STERILIZERS and disinfectors using hot air or hot inert gas as the sterilant; and
d) WASHER-DISINFECTORS.

  • Standard
    42 pages
    English language
    sale 10% off
    e-Library read for
    1 day

The contents of the corrigendum of March 2019 have been included in this copy.

  • Standard – translation
    41 pages
    Slovenian language
    sale 10% off
    e-Library read for
    1 day
  • Amendment
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This part of IEC 61010 specifies safety requirements for hand-held multimeters for domestic
and professional use, capable of measuring MAINS.
Hand-held multimeters are multi-range multifunction measuring instruments intended to
measure voltage and other electrical quantities such as resistance or current. Their primary
purpose is to measure voltage on a live MAINS. They are suitable to be supported by one hand
during NORMAL USE.

  • Standard
    46 pages
    English language
    sale 10% off
    e-Library read for
    1 day

1.1.1   Probe assemblies included in scope
This part of IEC 61010 specifies safety requirements for hand-held and hand-manipulated probe assemblies of the types described below, and their related accessories. These probe assemblies are for direct electrical connection between a part and electrical test and measurement equipment. They may be fixed to the
equipment or be detachable accessories for the equipment.
a) Type A: low-voltage and high-voltage, non-attenuating probe assemblies. Non-attenuating probe assemblies that are RATED for direct connection to voltages exceeding 30 V r.m.s., 42,4 V peak, or 60 V d.c., but not exceeding 63 kV. They do not incorporate components which are intended to provide a voltage divider function or a signal conditioning function, but they may contain non-attenuating components such as
fuses (see Figure 1).
b) Type B: high-voltage attenuating or divider probe assemblies. Attenuating or divider probe assemblies that are RATED for direct connection to secondary voltages exceeding 1 kV r.m.s or 1,5 kV d.c. but not exceeding 63 kV r.m.s or d.c. The divider function may be carried out wholly within the probe assembely, or partly within the test or measurement equipment to be used with the probe assembly (see Figure 2).
c) Type C: low-voltage attenuating or divider probe assemblies. Attenuating or divider probe assemblies for direct connection to voltages not exceeding 1 kV r.m.s. or 1,5 kV d.c. The signal conditioning function may be carried out wholly within the probe assembly, or partly within the test or measurement equipment intended to be used with the probe assembly (see Figure 3).
d) Type D: low-voltage attenuating, non-attenuating or other signal conditioning probe assemblies, that are RATED for direct connection only to voltages not exceeding 30 V r.m.s., or 42,4 V peak, or 60 V d.c., and are suitable for currents exceeding 8 A (see Figure 4).
1.1.2   Probe assemblies excluded from scope
This standard does not apply to current sensors within the scope of IEC 61010-2-032 (hand-held and hand-manipulated current sensors), but may apply to their input measuring circuit leads and accessories.

  • Amendment
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This Part 2 of IEC 61010 specifies particular safety requirements for the following types
a) to c) of electrical equipment and their accessories, wherever they are intended to be used,
whenever that equipment incorporates REFRIGERATING SYSTEMS as an integral part of, or
separate from, the equipment and the equipment is in direct control of the REFRIGERATING
SYSTEM.
This document details all the requirements when up to 150 g of FLAMMABLE REFRIGERANT are
used per stage of a REFRIGERATING SYSTEM. Additional requirements beyond the current scope
of this document apply if a REFRIGERANT charge of FLAMMABLE REFRIGERANT exceeds this
amount.

  • Standard
    53 pages
    English language
    sale 10% off
    e-Library read for
    1 day

1 Scope and object
This clause of Part 1 is applicable, except as follows:
1.1.1 Equipment included in scope
Replacement:
Replace the second paragraph by the following:
This Part 2 of IEC 61010 specifies particular safety requirements for the following types
a) to c) of electrical equipment and their accessories, wherever they are intended to be used,
whenever that equipment incorporates REFRIGERATING SYSTEMS as an integral part of, or
separate from, the equipment and the equipment is in direct control of the REFRIGERATING
SYSTEM.
This document details all the requirements when up to 150 g of FLAMMABLE REFRIGERANT are
used per stage of a REFRIGERATING SYSTEM. Additional requirements beyond the current scope
of this document apply if a REFRIGERANT charge of FLAMMABLE REFRIGERANT exceeds this
amount.
Addition:
Add the following text after the last paragraph:
NOTE 101 Examples for REFRIGERATING EQUIPMENT include, but are not limited to, laboratory equipment such as
laboratory refrigerators, freezers, refrigerated display cabinets.
It is possible that all or part of the equipment falls within the scope of one or more other
Part 2 standards of IEC 61010 as well as within the scope of this standard. In that case, the
requirements of those other Part 2 standards will also apply. In particular, if equipment is
intended to be used as a centrifuge, the requirements of IEC 61010-2-020 apply. However,
when the equipment incorporates a refrigerating system and a heating function where the
combination of the two introduces additional or more severe HAZARDS than if treated
separately, then it is possible that IEC 61010-2-012 is applicable instead of this Part 2-011.
See further information in the flow chart (Figure 102) for the selection process and guidance
in the Introduction.
1.1.2 Equipment excluded from scope
Addition:
Add the following new item after item j):
or equipment incorporating:
aa) a transcritical REFRIGERANT SYSTEM (system that uses CO2) or a system that uses
ammonia (NH3) as the REFRIGERANT.
1.2 Object
1.2.1 Aspects included in scope
Replacement:
Replace the first paragraph by the following:
The object of this document is to ensure that the design and methods of construction of
REFRIGERATING EQUIPMENT provide adequate protection for OPERATORS, bystanders, trained
service personnel, and the surrounding area against the specific HAZARDS that relate to
REFRIGERATING SYSTEMS.
Addition:
Add the following note after the existing note:
NOTE 101 A list of HAZARDS typically associated with REFRIGERATING SYSTEMS and REFRIGERANTS is included in
Annex BB.

  • Amendment
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day

NEXT ACTION: TB ACTION BY 2021-09-14: common mods, currently at ENQ
2019-10-03 JF: NWI for A11 (PR=70187) was approved by the BTthrough decision D163/098. The work on the amendment is under way
2019-03-11 TC is addressing the negative assessment and is invited to provide the information whether the changes will be needed in the main body of the amendment or only in Annex ZZ.
Negative assessment. IEC standard is published.

  • Amendment
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document applies to electrical equipment using signals in the frequency range 3 kHz to 95 kHz to transmit or receive information on low voltage electrical systems, for electricity suppliers and distributors. In the case of equipment which includes functions other than the transmission or reception of information on LV distribution networks or installations of network users connected to the public electricity distribution network, this document applies only to that part of the equipment intended for such transmission or reception of information. Other parts of the equipment are expected to comply with the immunity standard or standards relevant to the functions of those other parts.
The object of this document is to contribute to ensuring EMC in general. It specifies essential immunity requirements and test methods, including those tests which are to be performed during type-testing of MCE, for electromagnetic interference (EMI) generated on LV installations.
It defines the methods and requirements for testing immunity concerning the basic function of an MCE, in relation to continuous and transient disturbances, both conducted and radiated, and electrostatic discharges. Test requirements are specified for each port considered.
Furthermore it provides guidelines for the assessment of the performance of the communication function of an MCE. Normative specifications are under consideration.
This document gives limits which are applicable to MCE used by electricity suppliers and distributors (e.g. DSOs) for purposes like energy management and network monitoring and automation. The levels do not however cover extreme cases which could occur in any location but with a low probability of occurrence. In special cases situations will arise where the level of disturbances could exceed the levels specified in this document, e.g. where a hand-held transmitter is used in proximity of an apparatus. In these instances special mitigation measures might have to be employed.
It does not specify immunity between MCE operating in the same nominal frequency band or immunity to signals originating from power line carrier systems operating on high or medium-voltage networks.
Safety considerations are not included in this document.

  • Amendment
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day

1 Scope and object
This clause of Part 1 is applicable except as follows:
1.1.1 Equipment included in scope
Replacement:
Replace the existing text with the following:
This part of IEC 61010 specifies safety requirements for HAND-HELD and hand-manipulated
current sensors described below.
These current sensors are for measuring, detecting or injecting current, or indicating current
waveforms on circuits without physically opening the current path of the circuit being
measured. They may be stand-alone current sensors or accessories to other equipment or
parts of combined equipment (see Figure 101). These include measurement circuits which are
part of electrical test and measurement equipment, laboratory equipment, or process control
equipment. The existence of these current sensors and circuits in equipment requires
additional protective means between the current sensor, the circuit and an OPERATOR.

  • Amendment
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This part of IEC 61010 specifies safety requirements for HAND-HELD and hand-manipulated
current sensors described below.
These current sensors are for measuring, detecting or injecting current, or indicating current
waveforms on circuits without physically opening the current path of the circuit being
measured. They can be stand-alone current sensors or accessories to other equipment or
parts of combined equipment (see Figure 101). These include measurement circuits which are
part of electrical test and measurement equipment, laboratory equipment, or process control
equipment. These current sensors and circuits need additional protective means between the
current sensor, the circuit and an OPERATOR.
NOTE 1 Combined equipment is equipment that is electrically connected to a current sensor by means of a
permanent connection which can be detached only by the use of a TOOL.
NOTE 2 Some current sensors are also known as current clamps, CLAMP MULTIMETERS and current probes.
Current sensors are hand-manipulated before and/or after a test or measurement, but do not
necessarily need to be HAND-HELD during the test or measurement. Current sensors used as
FIXED EQUIPMENT are not within the scope of this document.

  • Standard
    67 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 61010-2-040:2020 is available as IEC 61010-2-040:2020 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61010-2-040:2020 specifies safety requirements for electrical equipment intended for sterilization, washing, and disinfection of medical materials in the medical, veterinary, pharmaceutical and laboratory fields, when used under the environmental conditions of 1.4. Examples of such equipment include the following: - sterilizers and disinfectors using steam and/or hot water as the sterilant; - sterilizers and disinfectors using toxic gas, toxic aerosol or toxic vapour as the sterilant; - sterilizers and disinfectors using hot air or hot inert gas as the sterilant; and - washer-disinfectors. This third edition cancels and replaces the second edition published in 2015. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - it is established on the basis of the third edition (2010) of IEC 61010‑1 and its Amendment 1 (2016); - added tolerance for stability of a.c. voltage test equipment to 6.8.3.1; - the status of a Group Safety Publication has been removed (this does not change the technical requirements in the document).

  • Standard
    42 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 61010-2-033:2019 is available as IEC 61010-2-033:2019 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61010-2-033:2019 specifies safety requirements for hand-held multimeters for domestic and professional use, capable of measuring mains. Hand-held multimeters are multi-range multifunction measuring instruments intended to measure voltage and other electrical quantities such as resistance or current. Their primary purpose is to measure voltage on a live mains. They are suitable to be supported by one hand during normal use. This second edition cancels and replaces the first edition published in 2012. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - The scope has been reduced to hand-held multimeters. Voltmeters and clamp multimeters have been removed. They are addressed respectively by IEC 61010-2-030 and IEC 61010-2-032. The relevant definitions have been removed. - Subclause 4.4.2.101 has been relocated into Clause 102. - Clearances and creepage distances for wet locations and for measuring circuit terminals exceeding 1 000 V a.c. or 1 414 V d.c. have been specified. - Subclause 14.101 related to "Circuits or components used as transient overvoltage limiting devices in measuring circuits used to measure mains" has been removed. - References to IEC 61010-031 for probe assemblies and IEC 61010-2-032 for current sensors have been added. - Requirements for protection against mains overvoltage measuring circuits have been added. - Clause 102 has been rewritten. - Requirements for measuring circuits from 1 000 V to 3 000 V have been added. - An informative Annex CC about dimensions of 4-mm banana terminals has been added. - A flowchart for insulation according to the type of circuit has been added in a new Annex DD.

  • Standard
    46 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document applies to electrical equipment using signals in the frequency range 3 kHz to 95 kHz to transmit or receive information on low voltage electrical systems, for electricity suppliers and distributors. In the case of equipment which includes functions other than the transmission or reception of information on LV distribution networks or installations of network users connected to the public electricity distribution network, this document applies only to that part of the equipment intended for such transmission or reception of information. Other parts of the equipment are expected to comply with the immunity standard or standards relevant to the functions of those other parts. The object of this document is to contribute to ensuring EMC in general. It specifies essential immunity requirements and test methods, including those tests which are to be performed during type-testing of MCE, for electromagnetic interference (EMI) generated on LV installations. It defines the methods and requirements for testing immunity concerning the basic function of an MCE, in relation to continuous and transient disturbances, both conducted and radiated, and electrostatic discharges. Test requirements are specified for each port considered. Furthermore it provides guidelines for the assessment of the performance of the communication function of an MCE. Normative specifications are under consideration. This document gives limits which are applicable to MCE used by electricity suppliers and distributors (e.g. DSOs) for purposes like energy management and network monitoring and automation. The levels do not however cover extreme cases which could occur in any location but with a low probability of occurrence. In special cases situations will arise where the level of disturbances could exceed the levels specified in this document, e.g. where a hand-held transmitter is used in proximity of an apparatus. In these instances special mitigation measures might have to be employed. It does not specify immunity between MCE operating in the same nominal frequency band or immunity to signals originating from power line carrier systems operating on high or medium-voltage networks. Safety considerations are not included in this document.

  • Amendment
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This part of IEC 61010 is applicable to electrically operated laboratory equipment and its
accessories for mechanical mixing and stirring, where mechanical energy influences the
shape or size or homogeneity of materials and their accessories. Such devices can contain
heating elements.
NOTE If all or part of the equipment falls within the scope of one or more other Part 2 standards of the IEC 61010
series as well as within the scope of this document, consideration is given to those other Part 2 standards. The
standard for equipment which contains heating devices is IEC 61010-2-010

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day

1 Scope and object
This clause of Part 1 is applicable except as follows:
1.1.1 Equipment included in scope
Replacement:
Replace the text, except the first paragraph, with the following new text:
This part of IEC 61010 is applicable to electrically operated laboratory equipment and its
accessories for mechanical mixing and stirring, where mechanical energy influences the
shape or size or homogeneity of materials and their accessories. Such devices can contain
heating elements.
NOTE If all or part of the equipment falls within the scope of one or more other Part 2 standards of the IEC 61010
series as well as within the scope of this document, consideration is given to those other Part 2 standards. The
standard for equipment which contains heating devices is IEC 61010-2-010.

  • Amendment
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This part of IEC 61010 applies to electrically powered laboratory atomic spectrometers with
thermal atomization.
NOTE 1 Examples include atomic absorption spectrometers, emission flame photometers, atomic fluorescence
spectrophotometers, inductively coupled plasma spectrometers, microwave coupled plasma spectrometers and
mass spectrometers, all with thermal atomization and ionization (including tubing and connectors which are
provided by the manufacturer for connection to external supplies).
NOTE 2 If all or part of the equipment falls within the scope of one or more other Part 2 documents of IEC 61010
as well as within the scope of this document, consideration is given to those other Part 2 documents.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day

EN-IEC 61010-2-130 specifies particular safety requirements for the following types of equipment a), b) or c) and their accessories intended to be used in  educational establishments by children under the supervision of the  RESPONSIBLE BODY. It specifies general safety requirements for equipment  intended to be used in educational establishments by persons between the age of 3 years and the age of 16 years under the supervision of a RESPONSIBLE BODY.Children are considered as persons between the age of 3 years and 16  years.It is recognized that pupils with additional educational or physical support  needs may have needs beyond the level addressed in this document (see Clause  17 risk assessment).It is possible that all or part of the equipment falls within the  scope of one or more IEC 61010 Part 2 standards as well as within the scope of  this document. In that case the requirements of those other Part 2 standards apply.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day

EN-IEC 61010-2-091 specifies particular safety requirements for cabinet X-ray systems, which fall under any of categories a), b) or c) below. Equipment covered by this document can be both PROTECTED EQUIPMENT or PARTIALLY PROTECTED EQUIPMENT, with X-ray generator voltage up to 500 kV. A cabinet X-ray system is a system that contains an X-ray tube installed in a cabinet, which, independently of existing architectural structures except the floor on which it may be placed, is intended to contain at least that portion of a material being irradiated, provide radiation attenuation and prevent operator access to the radiation beam, during generation of X-radiation. These cabinet X-ray systems are used in industrial, commercial, and public environments, for example, to inspect materials, to analyse materials, and to screen baggage.

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day

1 Scope and object
This clause of Part 1 is applicable, except as follows:
1.1 Scope
1.1.1 Equipment included in scope
Deletion:
Delete the first paragraph.
Replacement:
Replace the second paragraph (above items a) to c)) with the following new text:
This part of IEC 61010 specifies particular safety requirements for cabinet X-ray systems, which
fall under any of categories a), b) or c) below.
Addition:
Add the two following new paragraphs at the end of the subclause:
Equipment covered by this document can be both PROTECTED EQUIPMENT or PARTIALLY
PROTECTED EQUIPMENT, with X-ray generator voltage up to 500 kV.
A cabinet X-ray system is a system that contains an X-ray tube installed in a cabinet, which,
independently of existing architectural structures except the floor on which it may be placed, is
intended to contain at least that portion of a material being irradiated, provide radiation
attenuation and prevent operator access to the radiation beam, during generation of X-radiation.
These cabinet X-ray systems are used in industrial, commercial, and public environments, for
example, to inspect materials, to analyse materials, and to screen baggage.
1.1.2 Equipment excluded from scope
Addition:
Add the following new items to the list:
aa) Equipment intended to apply X-radiation to humans or animals;
bb) Equipment incorporating an X-ray tube but not incorporating complete shielding against
X-radiation HAZARDS, such as:
– equipment intended to be used within a shielded room which excludes personnel during
operation;
– equipment intended to be used with separate portable or temporary shielding;
– equipment intended to produce an emerging beam of X-radiation.
1.2 Object
1.2.1 Aspects included in scope
Addition:
Add the following new text to the end of the first paragraph:
This part of IEC 61010 specifies requirements for the design and methods of construction of
cabinet X-ray systems to provide adequate protection for OPERATORS, bystanders, trained
service personnel and the surrounding area against unintentionally-emitted X-radiation and from
mechanical HAZARDS related to their conveyors.

  • Amendment
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day

1   Scope and object
This clause of Part 1 is applicable except as follows:
1.1.1 Equipment included in scope
Replacement:
Replace the text with the following:
This group safety publication is primarily intended to be used as a product safety standard for the products mentioned in the scope, but shall also be used by technical committees in the preparation of their publications for products similar to those mentioned in the scope of this standard, in accordance with the principles laid down in IEC Guide 104 and lSO/lEC Guide 51.
This part of IEC 61010 specifies safety requirements for equipment having testing or measuring circuits which are connected for test or measurement purposes to devices or circuits outside the measurement equipment itself.
These include measuring circuits which are part of electrical test and measurement equipment, laboratory equipment, or process control equipment. The existence of these circuits in equipment requires additional protective means between the circuit and an OPERATOR.
NOTE These testing and measuring circuits can, for example:
–   measure voltages in circuits of other equipment,
–   measure temperature of a separate device via a thermocouple,
–   measure force on a separate device via a strain gauge,
–   inject a voltage onto a circuit to analyse a new design.
Equipment having these testing and measuring circuits may be intended for performing tests and measurements on hazardous conductors, including MAINS conductors and telecommunication network conductors. See Annex BB for considerations of HAZARDS involved in various tests and measurements.

  • Amendment
    5 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This group safety publication is primarily intended to be used as a product safety standard for
the products mentioned in the scope, but shall also be used by technical committees in the
preparation of their publications for products similar to those mentioned in the scope of this
standard, in accordance with the principles laid down in IEC Guide 104 and
lSO/lEC Guide 51.
This part of IEC 61010 specifies safety requirements for equipment having testing or
measuring circuits which are connected for test or measurement purposes to devices or
circuits outside the measurement equipment itself.
These include measuring circuits which are part of electrical test and measurement
equipment, laboratory equipment, or process control equipment. The existence of these
circuits in equipment requires additional protective means between the circuit and an
OPERATOR.
NOTE These testing and measuring circuits can, for example:
– measure voltages in circuits of other equipment,
– measure temperature of a separate device via a thermocouple,
– measure force on a separate device via a strain gauge,
– inject a voltage onto a circuit to analyse a new design.
Equipment having these testing and measuring circuits may be intended for performing tests
and measurements on hazardous conductors, including MAINS conductors and
telecommunication network conductors. See Annex BB for considerations of HAZARDS involved
in various tests and measurements.

  • Standard
    43 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This group safety publication is primarily intended to be used as a product safety standard for
the products mentioned in the scope, but shall also be used by technical committees in the
preparation of their publications for products similar to those mentioned in the scope of this
standard, in accordance with the principles laid down in IEC Guide 104 and lSO/lEC Guide 51.
This part of IEC 61010 specifies safety requirements for measurement equipment for
insulation resistance and test equipment for electric strength with an output voltage exceeding
50 V a.c. or 120 V d.c.
This document also applies to combined measuring equipment which has an insulation
resistance measurement function or an electric strength test measurement function.

  • Standard
    47 pages
    English language
    sale 10% off
    e-Library read for
    1 day

1   Scope and object
This clause of Part 1 is applicable except as follows:
1.1.1 Equipment included in scope
Replacement:
Replace the text with the following:
This group safety publication is primarily intended to be used as a product safety standard for the products mentioned in the scope, but shall also be used by technical committees in the preparation of their publications for products similar to those mentioned in the scope of this standard, in accordance with the principles laid down in IEC Guide 104 and lSO/lEC Guide 51.
This part of IEC 61010 specifies safety requirements for measurement equipment for insulation resistance and test equipment for electric strength with an output voltage exceeding 50 V a.c. or 120 V d.c..
This part also applies to combined measuring equipment which has an insulation resistance measurement function or an electric strength test measurement function.

  • Amendment
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day

1 Scope and object This clause of Part 1 is applicable, except as follows: 1.1 Scope 1.1.1 Equipment included in scope Deletion: Delete the first paragraph. Replacement: Replace the second paragraph (above items a) to c)) with the following new text: This part of IEC 61010 specifies particular safety requirements for cabinet X-ray systems, which fall under any of categories a), b) or c) below. Addition: Add the two following new paragraphs at the end of the subclause: Equipment covered by this document can be both PROTECTED EQUIPMENT or PARTIALLY PROTECTED EQUIPMENT, with X-ray generator voltage up to 500 kV. A cabinet X-ray system is a system that contains an X-ray tube installed in a cabinet, which, independently of existing architectural structures except the floor on which it may be placed, is intended to contain at least that portion of a material being irradiated, provide radiation attenuation and prevent operator access to the radiation beam, during generation of X-radiation. These cabinet X-ray systems are used in industrial, commercial, and public environments, for example, to inspect materials, to analyse materials, and to screen baggage. 1.1.2 Equipment excluded from scope Addition: Add the following new items to the list: aa) Equipment intended to apply X-radiation to humans or animals; bb) Equipment incorporating an X-ray tube but not incorporating complete shielding against X-radiation HAZARDS, such as: – equipment intended to be used within a shielded room which excludes personnel during operation; – equipment intended to be used with separate portable or temporary shielding; – equipment intended to produce an emerging beam of X-radiation. 1.2 Object 1.2.1 Aspects included in scope Addition: Add the following new text to the end of the first paragraph: This part of IEC 61010 specifies requirements for the design and methods of construction of cabinet X-ray systems to provide adequate protection for OPERATORS, bystanders, trained service personnel and the surrounding area against unintentionally-emitted X-radiation and from mechanical HAZARDS related to their conveyors.

  • Amendment
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 61010-2-091:2019 is available as IEC 61010-2-091:2019 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition. IEC 61010-2-091:2019 specifies particular safety requirements for cabinet X-ray systems, which fall under any of categories a), b) or c) below. a) Electrical test and measurement equipment This is equipment which by electromagnetic means tests, measures, indicates or records one or more electrical or physical quantities, also non-measuring equipment such as signal generators, measurement standards, power supplies for laboratory use, transducers, transmitters, etc. NOTE 1 This includes bench-top power supplies intended to aid a testing or measuring operation on another piece of equipment. Power supplies intended to power equipment are within the scope of IEC 61558 (see 1.1.2 h)). This standard also applies to test equipment integrated into manufacturing processes and intended for testing manufactured devices. NOTE 2 Manufacturing test equipment is likely to be installed adjacent to and interconnected with industrial machinery in this application. b) Electrical industrial process-control equipment This is equipment which controls one or more output quantities to specific values, with each value determined by manual setting, by local or remote programming, or by one or more input variables. c) Electrical laboratory equipment This is equipment which measures, indicates, monitors, inspects or analyses materials, or is used to prepare materials, and includes in vitro diagnostic (IVD) equipment. This equipment may also be used in areas other than laboratories; examples include selftest IVD equipment to be used in the home and inspection equipment to be used to check people or material during transportation. This second edition cancels and replaces the first edition published in 2012. It constitutes a technical revision. This edition includes the following significant changes from the first edition, as well as numerous other changes: - The scope of the document has been clarified and limited to equipment up to 500 kV. - Additional marking requirements for X-ray generating assemblies have been added. (5.1) - Requirements for high-voltage cables used in the X-ray assembly have been added. (6.5) - Insulation requirements have been added. (6.7) - Temperature requirements for beam-limiting devices have been added. (10.3) - Clarification has been provided on and , and test methods. (12) - Requirements for have been modified, taking into account functional safety standards. (15) - Requirements for reasonably foreseeable misuse have been clarified. (16) - Risk assessment has been made mandatory for specific aspects. (17)

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day

1 Scope and object This clause of Part 1 is applicable except as follows: 1.1.1 Equipment included in scope Replacement: Replace the text with the following: This group safety publication is primarily intended to be used as a product safety standard for the products mentioned in the scope, but shall also be used by technical committees in the preparation of their publications for products similar to those mentioned in the scope of this standard, in accordance with the principles laid down in IEC Guide 104 and lSO/lEC Guide 51. This part of IEC 61010 specifies safety requirements for measurement equipment for insulation resistance and test equipment for electric strength with an output voltage exceeding 50 V a.c. or 120 V d.c.. This part also applies to combined measuring equipment which has an insulation resistance measurement function or an electric strength test measurement function.

  • Amendment
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 61010-2-034:2017 This group safety publication is primarily intended to be used as a product safety standard for the products mentioned in the scope, but shall also be used by technical committees in the preparation of their publications for products similar to those mentioned in the scope of this standard, in accordance with the principles laid down in IEC Guide 104 and lSO/lEC Guide 51. IEC 61010-2-034:2017 specifies safety requirements for measurement equipment for insulation resistance and test equipment for electric strength with an output voltage exceeding 50 V a.c. or 120 V d.c. This document also applies to combined measuring equipment which has an insulation resistance measurement function or an electric strength test measurement function. It has the status of a horizontal standard in accordance with IEC Guide 104. This publication is to be read in conjunction with IEC 61010-1:2010.

  • Standard
    47 pages
    English language
    sale 10% off
    e-Library read for
    1 day

NEW!IEC 61010-2-030:2017 is available as IEC 61010-2-030:2017 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61010-2-030:2017 This group safety publication is primarily intended to be used as a product safety standard for the products mentioned in the scope, but shall also be used by technical committees in the preparation of their publications for products similar to those mentioned in the scope of this standard, in accordance with the principles laid down in IEC Guide 104 and lSO/lEC Guide 51. IEC 61010-2-030:2017 specifies safety requirements for equipment having testing or measuring circuits which are connected for test or measurement purposes to devices or circuits outside the measurement equipment itself. These include measuring circuits which are part of electrical test and measurement equipment, laboratory equipment, or process control equipment. The existence of these circuits in equipment requires additional protective means between the circuit and an OPERATOR. This second edition cancels and replaces the first edition published in 2010. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
Reference to IEC 61010-031 for probe assemblies and IEC 61010-032 for current sensors has been added.
Indirect bonding for testing and measuring circuits has been modified, in particular to take into account the duration of current flow versus body current for a.c. and d.c. currents according to IEC TS 60479-1 and IEC TS 60479-2.
Clearance and creepage distance for wet locations and for measuring circuit terminal exceeding 1 000 V a.c. or d.c have been specified.
The voltage source for testing overvoltage limiting component or circuit may be limited to 400 V.
Requirements against transient overvoltages for mains voltage measuring circuits have been added.
Requirements for measuring circuits from 1 000 V d.c. to 1 500 V d.c. have been added.
The corrigendum has been included in Tables K.102 to K.104.
Requirements for reduction of transient overvoltages have been modified.
An informative Annex CC about the dimensions of banana terminals has been added.
Flowchart for insulation according to the type of circuit has been added in a new Annex DD.  It has the status of a group safety publication in accordance with IEC Guide 104.

  • Standard
    43 pages
    English language
    sale 10% off
    e-Library read for
    1 day

1 Scope and object This clause of Part 1 is applicable except as follows: 1.1.1 Equipment included in scope Replacement: Replace the text with the following: This group safety publication is primarily intended to be used as a product safety standard for the products mentioned in the scope, but shall also be used by technical committees in the preparation of their publications for products similar to those mentioned in the scope of this standard, in accordance with the principles laid down in IEC Guide 104 and lSO/lEC Guide 51. This part of IEC 61010 specifies safety requirements for equipment having testing or measuring circuits which are connected for test or measurement purposes to devices or circuits outside the measurement equipment itself. These include measuring circuits which are part of electrical test and measurement equipment, laboratory equipment, or process control equipment. The existence of these circuits in equipment requires additional protective means between the circuit and an OPERATOR. NOTE These testing and measuring circuits can, for example: – measure voltages in circuits of other equipment, – measure temperature of a separate device via a thermocouple, – measure force on a separate device via a strain gauge, – inject a voltage onto a circuit to analyse a new design. Equipment having these testing and measuring circuits may be intended for performing tests and measurements on hazardous conductors, including MAINS conductors and telecommunication network conductors. See Annex BB for considerations of HAZARDS involved in various tests and measurements.

  • Amendment
    5 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 61010-2-202:2020 is available as IEC 61010-2-202:2020 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.

IEC 61010-2-202:2020 constitutes Part 2-202 of a planned series of standards on industrial-process measurement, control and automation equipment. Safety terms of general use are defined in IEC 61010-1. More specific terms are defined in each part. This part incorporates the safety related requirements of electrically operated valve ACTUATORs and SOLENOIDs. This document does not cover functional safety aspects of electrically operated ACTUATORs and SOLENOIDs.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day