77.140.50 - Flat steel products and semi-products
ICS 77.140.50 Details
Flat steel products and semi-products
Flachstahlprodukte und Halbzeuge
Produits et semi-produits plats en acier
Ploščati jekleni izdelki in polizdelki
General Information
e-Library Subscription
Create subscription and get permanent access to documents within 77.140.50 - Flat steel products and semi-products
Currently subscription includes documents marked with .We are working on making all documents available within the subscription.
This document specifies requirements for hot-rolled longitudinally profiled steel plates (LP steel plates). This document applies to hot-rolled LP steel plates with thickness between 4 mm and 400 mm for general structural and engineering purposes.
- Standard15 pagesEnglish languagesale 15% off
This document specifies tolerances on dimensions and shape for continuously hot-rolled uncoated plate/sheet and strip with a maximum width of 2 200 mm and a maximum thickness of 25 mm of non-alloy and alloy steels in accordance with Table 1 (see also Annex B). This document also applies to hot-rolled strip for cold rolling.
Table 1 - Field of application
[...table not represented...]
NOTE 1 This document does not apply to:
- hot-rolled strip rolled in widths w < 600 mm (see EN 10048);
- hot-rolled patterned steel strip and plate/sheet cut from wide strip (EN 10363);
- uncoated or electrolytically coated cold rolled sheet and strip (see EN 10131);
- hot-dip coated steel sheet and strip (EN 10143);
- stainless steels.
NOTE 2 This document can also be used for steels from other standards, e. g. steels for shipbuilding.
- Standard20 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies tolerances on dimensions and shape for continuously hot-rolled uncoated plate/sheet and strip with a maximum width of 2 200 mm and a maximum thickness of 25 mm of non-alloy and alloy steels in accordance with Table 1 (see also Annex B). This document also applies to hot-rolled strip for cold rolling.
Table 1 - Field of application
[...table not represented...]
NOTE 1 This document does not apply to:
- hot-rolled strip rolled in widths w < 600 mm (see EN 10048);
- hot-rolled patterned steel strip and plate/sheet cut from wide strip (EN 10363);
- uncoated or electrolytically coated cold rolled sheet and strip (see EN 10131);
- hot-dip coated steel sheet and strip (EN 10143);
- stainless steels.
NOTE 2 This document can also be used for steels from other standards, e. g. steels for shipbuilding.
- Standard20 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard is intended to define the test methods used for the determination of the following geometrical characteristics of electrical steel sheet and strip:
— edge wave (wave factor);
— residual curvature;
— edge camber;
— deviation from the shearing line due to internal stresses;
— burr height of cut edges.
This European Standard applies to electrical steel sheet and strip intended for the construction of magnetic circuits and corresponding to Clauses B2, C21 and C22 of IEC 60404-1:2000.
- Standard15 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard is intended to define the test methods used for the determination of the following geometrical characteristics of electrical steel sheet and strip:
— edge wave (wave factor);
— residual curvature;
— edge camber;
— deviation from the shearing line due to internal stresses;
— burr height of cut edges.
This European Standard applies to electrical steel sheet and strip intended for the construction of magnetic circuits and corresponding to Clauses B2, C21 and C22 of IEC 60404-1:2000.
- Standard15 pagesEnglish languagesale 10% offe-Library read for1 day
This document describes the mechanical testing methods, relevant for self-bonding coating assemblies with non-oriented electrical steels. In particular, it describes the mechanical testing methods, sample preparation, calibration methods, necessary to obtain reliable results that can be considered a reference for quality evaluation.
This document applies only to self-bonding coatings of non-oriented electrical steels.
- Technical report9 pagesEnglish languagesale 10% offe-Library read for1 day
This document describes the mechanical testing methods, relevant for self-bonding coating assemblies with non-oriented electrical steels. In particular, it describes the mechanical testing methods, sample preparation, calibration methods, necessary to obtain reliable results that can be considered a reference for quality evaluation.
This document applies only to self-bonding coatings of non-oriented electrical steels.
- Technical report9 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the technical delivery conditions for semi-finished products, hot or cold formed bars, rods, wire, sections and bright products of standard grades and special grades of corrosion resistant stainless steels for general purposes.
NOTE General purposes include the use of stainless steels in contact with foodstuffs.
The general technical delivery conditions specified in EN 10021 apply in addition to the specifications of this document, unless otherwise specified in this document.
This document does not apply to components manufactured by further processing of the product forms listed above with quality characteristics altered as a result of such further processing.
- Standard94 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the technical delivery conditions for semi-finished products, hot or cold formed bars, rods, wire, sections and bright products of standard grades and special grades of corrosion resistant stainless steels for general purposes.
NOTE General purposes include the use of stainless steels in contact with foodstuffs.
The general technical delivery conditions specified in EN 10021 apply in addition to the specifications of this document, unless otherwise specified in this document.
This document does not apply to components manufactured by further processing of the product forms listed above with quality characteristics altered as a result of such further processing.
- Standard94 pagesEnglish languagesale 10% offe-Library read for1 day
This document applies to cold rolled non-coated low carbon steel flat products in rolled widths equal to or over 600 mm and in thicknesses equal to or less than 3 mm, delivered in sheet, wide strip, slit wide strip or cut lengths obtained from slit wide strip or sheet.
It does not apply to cold rolled narrow strip (rolling width < 600 mm) or to cold rolled flat products for which there is a specific standard, in particular the following:
- cold-rolled low carbon steel flat products for cold forming (EN 10130);
- cold-rolled non-oriented electrical steel sheet and strip delivered in fully processed state (EN 10106);
- cold rolled electrical non-alloy and alloy steel sheet and strip delivered in the semi-processed state (EN 10341);
- cold reduced blackplate (EN 10205);
- steel sheet and strip for welded gas cylinders (EN 10120);
- cold-rolled uncoated non-alloy mild steel narrow strip for cold forming (EN 10139);
- cold-rolled structural steels for general purposes;
- cold-rolled flat products made of high yield strength for cold forming (EN 10268).
- Standard26 pagesEnglish languagesale 10% offe-Library read for1 day
This part of EN 508 specifies requirements for self-supporting products for roof covering, wall cladding, lining, liner tray and tile products for discontinuous laying made from stainless steel sheets with or without additional metallic and/or organic coatings. Sheets intended to be used with insulation and membranes are also covered.
This document establishes general characteristics, definitions, classifications and labelling for the products, together with requirements for the materials from which the products can be manufactured. It is intended to be used either by manufacturers to ensure that their products comply with the requirements or by purchasers to verify that the products comply before they are dispatched from the factory. It specifies the requirements for products which enable them to meet all normal service conditions.
This document applies to all discontinuously laid self-supporting external profiled sheets for roof covering, wall cladding, lining, liner trays and tile products with the exception of tiles with a surface area less than 1 m2 and produced by stamping. These profiled roof sheets are designed to keep wind, rain and snow out of the building and to transfer any resultant loads and infrequent maintenance loads to the structure.
This document does not cover products for structural purposes, i.e. it does cover products used in structural class III (according to EN 1993-1-3), it does not cover products used in constructions of structural classes I and II (according to EN 1993-1-3) intended to contribute to the global or partial stability of the building structure by providing racking resistance or resistance to permanent static loads (excluding self-weight of the metal sheet).
No requirements for supporting construction, design of roof or cladding, lining, tile system and execution of connections and flashings are included.
- Standard40 pagesEnglish languagesale 10% offe-Library read for1 day
This document applies to cold rolled non-coated low carbon steel flat products in rolled widths equal to or over 600 mm and in thicknesses equal to or less than 3 mm, delivered in sheet, wide strip, slit wide strip or cut lengths obtained from slit wide strip or sheet.
It does not apply to cold rolled narrow strip (rolling width < 600 mm) or to cold rolled flat products for which there is a specific standard, in particular the following:
- cold-rolled low carbon steel flat products for cold forming (EN 10130);
- cold-rolled non-oriented electrical steel sheet and strip delivered in fully processed state (EN 10106);
- cold rolled electrical non-alloy and alloy steel sheet and strip delivered in the semi-processed state (EN 10341);
- cold reduced blackplate (EN 10205);
- steel sheet and strip for welded gas cylinders (EN 10120);
- cold-rolled uncoated non-alloy mild steel narrow strip for cold forming (EN 10139);
- cold-rolled structural steels for general purposes;
- cold-rolled flat products made of high yield strength for cold forming (EN 10268).
- Standard26 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the requirements for laser welded tailored blanks (LWB) made of steels for all cold or hot forming processes.
This document applies to all steel grades with or without metallic and/or organic coatings, having uniform or different sheet thickness, welded with or without extra material addition.
After the welding process, LWB are further processed to pressed parts by forming operations under the responsibility of the processor.
- Standard28 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the requirements for laser welded tailored blanks (LWB) made of steels for all cold or hot forming processes.
This document is applicable to all steel grades with or without metallic and/or organic coatings, having uniform or different sheet thickness, welded with or without extra material addition.
After the welding process, LWB are further processed to pressed parts by forming operations under the responsibility of the processor.
- Standard28 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the requirements for steel sheet, zinc-coated and zinc-iron alloy-coated by the continuous hot-dip process, of structural quality. The product is intended for applications where resistance to corrosion is of prime importance. The steel sheet is produced in a number of grades, coating masses, ordering conditions, and surface treatments. This document does not cover steel sheet designated as commercial quality, or drawing quality, which are covered in ISO 3575.
- Standard14 pagesEnglish languagesale 15% off
This document specifies the requirements relating to:
Steel X5CrNiCu 17-4 (1.4542)
Air melted
Solution treated and precipitation treated
Sheets and strips
a ≤ 6 mm
Rm ≥ 1 070 MPa
for aerospace applications.
W.nr: 1.4542.
The ASD-STAN designation of this material is FE-PM3801.
- Standard9 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the requirements relating to:
Steel X5CrNiCu15-5 (1.4545)
Consumable electrode remelted
Solution treated and precipitation treated
Plates
6 mm < a ≤ 20 mm
1 070 MPa ≤ Rm ≤ 1 220 MPa
for aerospace applications.
- Standard9 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the requirements relating to:
Steel X5CrNiCu 17-4 (1.4542)
Air melted
Solution treated and precipitation treated
Plates
6 mm ≤ a ≤ 100 mm
Rm ≥ 1 070 MPa
for aerospace applications.
W.nr: 1.4542.
The ASD-STAN designation of this material is FE-PM3801.
- Standard9 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies technical delivery conditions for flat and long products of hot rolled weldable fine grain structural steels in the thermomechanical rolled condition in the grades and qualities given in Tables 1 to 3 (chemical composition) and Tables 4 to 6 (mechanical properties) in thickness ≤ 150 mm.
The steels specified in this document are especially intended for use in heavily loaded parts of welded structures such as, bridges, flood gates, storage tanks, water supply tanks, etc., for service at ambient and low temperatures.
- Standard30 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies technical delivery conditions for flat products of high yield strength alloy special steels. The grades and qualities are given in Tables 1 to 3 (chemical composition) and Tables 4 to 6 (mechanical properties) and are supplied in the quenched and tempered condition.
The steels specified in this document are applicable to hot-rolled flat products with a minimum nominal thickness of 3 mm and a maximum nominal thickness of 200 mm for grades S460, S500, S550, S620 and S690, a maximum nominal thickness of 125 mm for grades S890 and S960, in steels which, after quenching and tempering, have a specified minimum yield strength of 460 MPa to 960 MPa.
- Standard28 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies technical delivery conditions for flat and long products of hot rolled weldable fine grain structural steels in the thermomechanical rolled condition in the grades and qualities given in Tables 1 to 3 (chemical composition) and Tables 4 to 6 (mechanical properties) in thickness ≤ 150 mm.
The steels specified in this document are especially intended for use in heavily loaded parts of welded structures such as, bridges, flood gates, storage tanks, water supply tanks, etc., for service at ambient and low temperatures.
- Standard30 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies technical delivery conditions for flat products of high yield strength alloy special steels. The grades and qualities are given in Tables 1 to 3 (chemical composition) and Tables 4 to 6 (mechanical properties) and are supplied in the quenched and tempered condition.
The steels specified in this document are applicable to hot-rolled flat products with a minimum nominal thickness of 3 mm and a maximum nominal thickness of 200 mm for grades S460, S500, S550, S620 and S690, a maximum nominal thickness of 125 mm for grades S890 and S960, in steels which, after quenching and tempering, have a specified minimum yield strength of 460 MPa to 960 MPa.
- Standard28 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies a method for determination of the biaxial stress-strain curve of metallic
sheets having a thickness below 3 mm in pure stretch forming without significant friction influence. In
comparison with tensile test results, higher strain values can be achieved.
NOTE In this document, the term "biaxial stress-strain curve" is used for simplification. In principle, in the
test the "biaxial true stress-true strain curve" is determined.
- Standard31 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies requirements for continuously organic coated (coil coated) steel flat products. It particularly specifies the performance requirements.
The products covered are wide strip, sheet cut from wide strip, slit wide strip, strip rolled in widths less than 600 mm and cut lengths (from sheet or strip).
NOTE National provisions can set up relationships between the performances of the coatings as required in this document and the outdoor atmospheres and ambiances required for a relevant building under study.
This document is not applicable to continuously organic coated flat products made of:
- tin mill products;
- electrical steels.
- Standard41 pagesEnglish languagesale 10% offe-Library read for1 day
This document defines the steel grades of grain-oriented electrical steel strip and sheet in nominal thicknesses of 0,20 mm, 0,23 mm, 0,27 mm, 0,30 mm and 0,35 mm. In particular, it gives general requirements, magnetic properties, geometric characteristics, tolerances and technological characteristics, as well as inspection procedures.
This document applies to Goss textured grain-oriented electrical steel strip and sheet supplied in the final annealed condition in coils or sheets and intended for the construction of magnetic circuits.
The grades are grouped into three classes:
- conventional grades;
- high permeability grades;
- magnetic domain refined high permeability grades.
They correspond to Class C22 of IEC 60404-1.
- Standard21 pagesEnglish languagesale 10% offe-Library read for1 day
This document defines the steel grades of grain-oriented electrical steel strip and sheet in nominal thicknesses of 0,20 mm, 0,23 mm, 0,27 mm, 0,30 mm and 0,35 mm. In particular, it gives general requirements, magnetic properties, geometric characteristics, tolerances and technological characteristics, as well as inspection procedures.
This document applies to Goss textured grain-oriented electrical steel strip and sheet supplied in the final annealed condition in coils or sheets and intended for the construction of magnetic circuits.
The grades are grouped into three classes:
- conventional grades;
- high permeability grades;
- magnetic domain refined high permeability grades.
They correspond to Class C22 of IEC 60404-1.
- Standard21 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies requirements for tinmill products in the form of sheets or coils. Tinmill products consist of single and double reduced low carbon mild steel electrolytically coated with either tin (tinplate) or chromium/chromium oxide (ECCS) or (ECCS-RC) (see 3.3).
Single reduced tinmill products are specified in nominal thicknesses that are multiples of 0,005 mm from 0,16 mm up to and including 0,49 mm. Double reduced tinmill products are specified in nominal thicknesses that are multiples of 0,005 mm from 0,12 mm up to and including 0,29 mm.
NOTE 1 Other thicknesses can be ordered upon agreement.
This document applies to coils and sheets cut from coils in nominal minimum widths of 600 mm.
NOTE 2 Standard width coils for specific uses, e.g. tabstock, can be slit into narrow strip for supply in coil form.
- Standard63 pagesEnglish languagesale 10% offe-Library read for1 day
This technical report describes the qualification methods, relevant for the non-oriented electrical steel coatings described in EN 10342. In particular, it describes the testing methods, sample preparation, calibration methods, that are necessary to obtain reliable results that can be considered a reference for quality evaluation.
- Technical report11 pagesEnglish languagesale 10% offe-Library read for1 day
This document describes the qualification methods, relevant for the non-oriented electrical steel coatings described in EN 10342. In particular, it describes the testing methods, sample preparation, calibration methods, that are necessary to obtain reliable results that can be considered a reference for quality evaluation.
This document applies only to the coatings of non-oriented electrical steels.
- Technical report11 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the requirements relating to:
Steel X4CrNiMo16-5-1
Air melted
Hardened and tempered
Sheets and plates
0,3 mm ≤ a ≤ 50 mm
900 MPa ≤ Rm ≤ 1 050 MPa
for aerospace applications.
ASD-STAN designation: FE-PM 3504
- Standard9 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the technical delivery conditions for cold rolled narrow steel strip made of non alloy and alloy steel grades in the form of coils and cut lengths in rolling widths less than 600 mm. Cold rolled narrow steel strip is available in grades of case hardening steel and of steels for quenching and tempering for general and special applications particularily springs.
- Case hardening steels in thicknesses up to and including 10 mm;
- steels for quenching and tempering in thicknesses up to and including 6 mm in the conditions annealed (+A), annealed and skin passed (+LC) or cold rolled (+CR);
- steels in the quenched and tempered condition (+QT) in thicknesses between 0,30 mm and 3,00 mm.
In special cases supplementary requirements or deviations with respect to this document can be agreed between the purchaser and the supplier at the time of enquiry and order (see 5.2 and Annex A).
In addition to the requirements of this document, the general technical delivery requirements specified in EN 10021 apply.
This document does not cover cold rolled flat products for which separate standards exist, e.g.:
- cold rolled uncoated low carbon steel narrow strip for cold forming (EN 10139);
- cold rolled steel flat products with higher yield strength for cold forming (EN 10268).
- Standard24 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies requirements for continuously organic coated (coil coated) steel flat products. It particularly specifies the performance requirements.
The products covered are wide strip, sheet cut from wide strip, slit wide strip, strip rolled in widths less than 600 mm and cut lengths (from sheet or strip).
NOTE National provisions can set up relationships between the performances of the coatings as required in this document and the outdoor atmospheres and ambiances required for a relevant building under study.
This document is not applicable to continuously organic coated flat products made of:
- tin mill products;
- electrical steels.
- Standard41 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies requirements for tinmill products in the form of sheets or coils. Tinmill products consist of single and double reduced low carbon mild steel electrolytically coated with either tin (tinplate) or chromium/chromium oxide (ECCS) or (ECCS-RC) (see 3.3).
Single reduced tinmill products are specified in nominal thicknesses that are multiples of 0,005 mm from 0,16 mm up to and including 0,49 mm. Double reduced tinmill products are specified in nominal thicknesses that are multiples of 0,005 mm from 0,12 mm up to and including 0,29 mm.
NOTE 1 Other thicknesses can be ordered upon agreement.
This document applies to coils and sheets cut from coils in nominal minimum widths of 600 mm.
NOTE 2 Standard width coils for specific uses, e.g. tabstock, can be slit into narrow strip for supply in coil form.
- Standard63 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the requirements for hot-rolled twin-roll cast steel sheet of structural quality and high strength steel. The product is intended for applications where specific mechanical properties are required. It is generally used in the delivered condition and is intended for bolted, riveted or welded structures, and it is produced on a wide strip mill, not a plate mill. Structural quality twin-roll cast steel sheet is a carbon steel produced to specified mechanical properties and is available in a number of grades. High strength hot-rolled twin-roll cast steel sheet, strengthened by microalloys is produced to specified mechanical properties and is available in a number of grades and classes.
- Standard9 pagesEnglish languagesale 15% off
This document specifies the requirements for steel sheet, in coils and cut length, metallic-coated by the continuous hot-dip zinc-coated twin-roll cast process of commercial quality. The steel sheet is intended for applications requiring corrosion resistance, formability and paintability. The steel sheet is produced in a number of grades, coating masses, surface treatments and ordering conditions.
- Standard13 pagesEnglish languagesale 15% off
This document specifies the requirements for steel sheet, in coils and cut length, metallic-coated by the continuous hot-dip zinc-coated twin-roll cast process, of structural and high strength quality. The product is intended for applications requiring corrosion resistance, and paintability. The steel sheet is produced in a number of grades, coating masses, surface treatments and ordering conditions.
- Standard16 pagesEnglish languagesale 15% off
This part of EN 508 specifies requirements for self-supporting roofing, covering, wall cladding, lining, liner tray and tile products for discontinuous laying made from metallic coated steel sheet with or without additional organic coatings. Sheets intended to be used with insulation and membranes are also covered.
This document establishes general characteristics, definitions, classifications and labelling for the products, together with requirements for the materials from which the products can be manufactured. It is intended to be used either by manufacturers to ensure that their products comply with the requirements or by purchasers to verify that the products comply when purchased before they are despatched from the factory. It specifies the requirements for products which enable them to meet all normal service conditions.
This document applies to all discontinuously laid self-supporting external profiled sheets for roofing covering, wall cladding, lining, and liner trays, with the exception of tiles with a surface area less than 1 m2 and produced by stamping. These profiled sheets are designed to keep wind, rain and snow out of the building and to transfer any resultant loads and infrequent maintenance loads to the structure.
This document does not cover products for structural purposes, i.e. it does cover products used in constructions of structural Class III (according to EN 1993 1 3), it does not cover products used in constructions of structural Classes I and II (according to EN 1993 1 3) intended to contribute to the global or partial stability of the building structure by providing racking resistance or resistance to permanent static loads (excluding self-weight of the metal sheet).
No requirements for supporting construction, design of roof, cladding, lining, tile system and execution of connections and flashings are included.
- Standard48 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies delivery requirements applicable to the surface finish of hot-rolled plates rolled on reversing mills and wide flats, with a nominal thickness ≥3 mm and ≤400 mm.
- Standard14 pagesEnglish languagesale 15% off
- Standard14 pagesEnglish languagesale 15% off
This document specifies the technical delivery conditions for cold rolled narrow steel strip made of non alloy and alloy steel grades in the form of coils and cut lengths in rolling widths less than 600 mm. Cold rolled narrow steel strip is available in grades of case hardening steel and of steels for quenching and tempering for general and special applications particularily springs.
— Case hardening steels in thicknesses up to and including 10 mm;
— Steels for quenching and tempering in thicknesses up to and including 6 mm in the conditions annealed (+A), annealed and skin passed (+LC) or cold rolled (+CR);
— Steels in the quenched and tempered condition (+QT) in thicknesses between 0,30 mm and 3,00 mm.
In special cases supplementary requirements or deviations with respect to this document can be agreed between the purchaser and the supplier at the time of enquiry and order (see 5.2 and Annex A).
In addition to the requirements of this document, the general technical delivery requirements specified in EN 10021 apply.
This document does not cover cold rolled flat products for which separate standards exist, e.g.:
— Cold rolled uncoated low carbon steel narrow strip for cold forming (EN 10139);
— Cold rolled steel flat products with higher yield strength for cold forming (EN 10268).
- Standard24 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the requirements for hot-rolled twin-roll cast steel sheet of commercial quality. The product is intended for applications where the presence of oxide or scale or normal surface imperfections disclosed after removal of oxide or scale are not objectionable. It is not suitable for applications where the surface is of prime importance. This document does not cover steel sheet that is subjected to subsequent rolling.
- Standard8 pagesEnglish languagesale 15% off
- Standard8 pagesEnglish languagesale 15% off
This document specifies testing conditions for use when constructing a forming-limit curve (FLC) at
ambient temperature and using linear strain paths. The material considered is flat, metallic and of
thickness between 0,3 mm and 4 mm.
NOTE The limitation in thickness of up to 4 mm is proposed, giving a maximum allowable thickness to the
punch diameter ratio.
- Standard36 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies a procedure for developing forming-limit diagrams and forming-limit curves
for metal sheets and strips of thicknesses from 0,3 mm to 4 mm.
- Standard16 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies a method for determining the tensile strain hardening exponent n of flat
products (sheet and strip) made of metallic materials.
The method is valid only for that part of the stress-strain curve in the plastic range where the curve is
continuous and monotonic (see 8.4).
In the case of materials with a serrated stress-strain curve in the work hardening range (materials
which show the Portevin-Le Chatelier effect, e.g. AlMg-alloys), the automatic determination (linear
regression of the logarithm true stress vs. the logarithm true plastic strain, see 8.7) is used to give
reproducible results.
- Standard18 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies a method using a barcoding system for tracing isolated defects that can be present in the following kinds of coated or uncoated steel flat products, for example:
- electro-galvanised surface;
- galvanised surface;
- galvannealed surface;
- cold rolled surface.
This method, named "quality tracking", aims to transfer additional material information to steel users, in particular the location of some isolated defects, in a reliable way. This method enables the manufacturer or purchaser to remove blanks or coils containing defects.
The method uses a 1D barcode to identify each section of steel strip.
NOTE 1 The stakeholders most involved in this technique are suppliers of steel flat products, car makers, appliance makers, part manufacturers, blanking line builders, steel processors, service centres, etc. All stakeholders can benefit from this project since defects can be traced, and, therefore, the steel containing defects can be eliminated or set apart of the production line.
NOTE 2 In the first stages of development, this method was called "defect tracking" (see [3]) and has been changed into "quality tracking" at the beginning of the standardization process.
NOTE 3 Quality tracking can be applied to other types of coated or uncoated steel flat products such as pickled and oiled, organic coated, and steels for packaging. Quality tracking can be applied for coiled materials for which the technology of quality tracking is applicable.
NOTE 4 If quality tracking data are used outside of the purpose of quality tracking, it is under the responsibility of the user.
NOTE 5 Quality tracking can be applied to other materials than steel.
NOTE 6 The way to collect the information to be transferred to the user is out of the scope of this document.
- Standard18 pagesEnglish languagesale 10% offe-Library read for1 day
1.1 This European Standard applies to cold rolled narrow strip in coils and cut lengths in thicknesses up to 10 mm and of widths less than 600 mm, made from low carbon, unalloyed and alloyed steels in accordance with Table 1.
These products are suitable for cold forming. They are also suitable for surface coating. On the other hand, they are not suitable for hardening treatment followed by tempering.
1.2 This European Standard does not cover cold rolled flat products for which a separate standard already exists, particularly the following products:
- cold rolled non-oriented electrical steel sheet and strip delivered in the fully processed state (EN 10106);
- grain-oriented electrical steel sheet and strip delivered in the fully processed state (EN 10107);
- cold rolled electrical non-alloy and alloy steel sheet and strip delivered in the semi-processed state (EN 10341);
- cold rolled narrow steel strip for heat treatment (EN 10132 1 to −4);
- cold rolled steel flat products with higher yield strength for cold forming (EN 10268);
- cold rolled low carbon steel flat products for cold forming (EN 10130);
- cold reduced blackplate in coil form for the production of tinplate or electrolytic chromium/chromium oxide coated steel (EN 10205);
- cold rolled low carbon steel flat products for vitreous enamelling (EN 10209).
- Standard14 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies a method using a barcoding system for tracing potential isolated defects that can be present in the following kinds of coated or uncoated steel flat products, for example:
- electro-galvanised surface
- galvanised surface
- galvannealed surface
- cold rolled surface
This method, named “quality tracking”, aims at transferring additional material information to the steel users, especially the location of some isolated defects, in a reliable way. This method enables the manufacturer or purchaser to eliminate blanks or coils containing defects.
The method uses a 1D barcode to identify each section of steel strip.
NOTE 1 The stakeholders most involved in this technique are suppliers of steel flat products, car makers, appliance makers, part manufacturers, blanking line builders, steel processors, service centres, etc. All stakeholders can benefit from this project since defects can be traced, and, therefore, the steel containing defects can be eliminated or set apart of the production line.
NOTE 2 In the first stages of development, this method was called "defect tracking" (see [1]) and has been changed into "quality tracking" at the beginning of the standardization process.
NOTE 3 Quality tracking can be applied to other types of coated or uncoated steel flat products such as pickled and oiled, organic coated, and steels for packaging. Quality tracking can be applied for coiled materials for which the technology of quality tracking is applicable.
NOTE 4 If quality tracking data are used outside of the purpose of quality tracking, it is under the responsibility of the user.
NOTE 5 Quality tracking can be applied to other materials than steel.
NOTE 6 The way to collect the information to be transferred to the user is out of the scope of this document.
- Standard18 pagesEnglish languagesale 10% offe-Library read for1 day
1.1 This European Standard applies to cold rolled narrow strip in coils and cut lengths in thicknesses up to 10 mm and of widths less than 600 mm, made from low carbon, unalloyed and alloyed steels in accordance with Table 1.
These products are suitable for cold forming. They are also suitable for surface coating. On the other hand, they are not suitable for hardening treatment followed by tempering.
1.2 This European Standard does not cover cold rolled flat products for which a separate standard already exists, particularly the following products:
- cold rolled non-oriented electrical steel sheet and strip delivered in the fully processed state (EN 10106);
- grain-oriented electrical steel sheet and strip delivered in the fully processed state (EN 10107);
- cold rolled electrical non-alloy and alloy steel sheet and strip delivered in the semi-processed state (EN 10341);
- cold rolled narrow steel strip for heat treatment (EN 10132 1 to −4);
- cold rolled steel flat products with higher yield strength for cold forming (EN 10268);
- cold rolled low carbon steel flat products for cold forming (EN 10130);
- cold reduced blackplate in coil form for the production of tinplate or electrolytic chromium/chromium oxide coated steel (EN 10205);
- cold rolled low carbon steel flat products for vitreous enamelling (EN 10209).
- Standard14 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the technical delivery conditions for flat and long products as well as semi-finished products which are meant for further processing to flat and long products of hot rolled non-alloy quality steels in the grades and qualities given in Tables 1 to 5 (chemical composition) and Tables 6 to 8 (mechanical properties) in the usual delivery conditions as given in 6.3. Three engineering steels are also specified in this document (see Tables 2 and 4) (chemical composition) and Table 7 (mechanical properties). This document does not apply to structural hollow sections (see EN 10210 1 and EN 10219 1) and tubes.
The technical delivery conditions apply to:
- thicknesses ≥ 3 mm and ≤ 150 mm for long products of steel grade S460JR, J0, J2, K2 and S500J0;
- thicknesses ≤ 400 mm for flat products of qualities JR, J0, J2 and K2;
- thicknesses ≤ 250 mm for flat and long products of all other grades and qualities.
The steels specified in this document are not intended to be heat treated except products delivered in the delivery condition +N. Stress relieving is accepted. Products delivered in +N condition can be hot formed and/or normalized after delivery (see Clause 3).
This document foresees that semi-finished products which are to be converted to rolled finished products conforming to this document are the subject of special agreements at the time of the order. The chemical compositions are also agreed to at the time of the order; the values are within the limits of Tables 1 and 2.
For certain grades and product forms suitability for particular applications are specified at the time of the order (see 7.4.2, 7.4.3 and Table 9).
- Standard41 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies technical delivery conditions for flat and long products of hot rolled steels with improved atmospheric corrosion resistance in the grades and qualities given in Tables 2 and 3 (chemical composition) and Tables 4 and 5 (mechanical properties) in the usual delivery conditions as given in 6.3.
The thicknesses in which products of the steel grades and qualities specified in this document can be supplied are given in Table 1.
Table 1 - Product forms for the different steel grades with improved atmospheric corrosion resistance depending on their thickness
[table not reproduced]
The steels specified in this document are not intended to be heat treated except products delivered in the delivery condition +N. Stress relieving is accepted. Products delivered in +N condition can be hot formed and/or normalized after delivery (see Clause 3).
- Standard36 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies technical delivery conditions for flat and long products of hot rolled weldable fine grain structural steels in the normalized/normalized rolled delivery condition in the grades and qualities given in Tables 1 to 3 (chemical composition) and Tables 4 to 6 (mechanical properties) in thickness ≤ 250 mm.
The steels specified in this document are especially intended for use in heavily loaded parts of welded structures such as, bridges, flood gates, storages tanks, water supply tanks, etc., for service at ambient and low temperatures.
- Standard31 pagesEnglish languagesale 10% offe-Library read for1 day