This document applies to patented cold drawn unalloyed steel wire of circular cross-section for the
manufacture of mechanical springs for static duty and dynamic duty applications.
General technical delivery requirements can be found in EN 10021.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the technical delivery conditions for semi-finished products, hot or cold formed bars, rods, wire, sections and bright products of standard grades and special grades of corrosion resistant stainless steels for general purposes.
NOTE   General purposes include the use of stainless steels in contact with foodstuffs.
The general technical delivery conditions specified in EN 10021 apply in addition to the specifications of this document, unless otherwise specified in this document.
This document does not apply to components manufactured by further processing of the product forms listed above with quality characteristics altered as a result of such further processing.

  • Standard
    94 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies round and shaped non alloyed steel wire for use in the manufacture of ropes for mine hoisting, man-riding haulage, cableways for the transportation of passengers and other high duty applications. Heavy duty refers to situations where the stresses applied to the rope are either high or vary by a large amount during service.
This document refers to round wires and three types of shaped wire: full lock (Z), half lock (H) and trapezoidal (T).
It does not apply to steel wire taken from manufactured ropes.
This document specifies the following for cold drawn non alloyed steel wire for ropes for high duty applications:
-   dimensional tolerances;
-   mechanical characteristics;
-   requirements relating to the chemical composition of the steel wire;
-   conditions to be satisfied by any coating.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the technical delivery conditions for semi-finished products, hot or cold formed bars, rods, wire, sections and bright products of standard grades and special grades of corrosion resistant stainless steels for general purposes.
NOTE   General purposes include the use of stainless steels in contact with foodstuffs.
The general technical delivery conditions specified in EN 10021 apply in addition to the specifications of this document, unless otherwise specified in this document.
This document does not apply to components manufactured by further processing of the product forms listed above with quality characteristics altered as a result of such further processing.

  • Standard
    94 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies round and shaped non alloyed steel wire for use in the manufacture of ropes for mine hoisting, man-riding haulage, cableways for the transportation of passengers and other high duty applications. Heavy duty refers to situations where the stresses applied to the rope are either high or vary by a large amount during service.
This document refers to round wires and three types of shaped wire: full lock (Z), half lock (H) and trapezoidal (T).
It does not apply to steel wire taken from manufactured ropes.
This document specifies the following for cold drawn non alloyed steel wire for ropes for high duty applications:
-   dimensional tolerances;
-   mechanical characteristics;
-   requirements relating to the chemical composition of the steel wire;
-   conditions to be satisfied by any coating.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies requirements for wire rod for bridge cable wire, which is widely used in parallel wire cables or semi-parallel wire cables for suspension bridges, stay bridges or other structures involving the use of parallel wires. ISO 16120-4 provides additional wire rod materials and their technical and qualitative requirements for their possible application as bridge cable wire.

  • Standard
    8 pages
    English language
    sale 15% off

This document specifies the minimum requirements and terms of acceptance for the manufacture and testing of steel wire ropes not exceeding rope grade 2160 for the petroleum and natural gas industries. Typical applications include tubing lines, rod hanger lines, sand lines, cable-tool drilling and clean out lines, cable tool casing lines, rotary drilling lines, winch lines, horse head pumping unit lines, torpedo lines, mast‑raising lines, guideline tensioner lines, riser tensioner lines, mooring and anchor lines. Wire ropes for lifting slings and cranes, and wire for well-measuring and strand for well-servicing are also included. The minimum breaking forces for the more common sizes, grades and constructions of stranded rope are given in tables. However, this document does not restrict itself to the classes covered by those tables. Other types can also conform with its requirements. The minimum breaking force values for these wire ropes are provided by the manufacturer. For information only, other tables present the minimum breaking forces for large diameter stranded and spiral ropes (i.e. spiral strand and locked coil), while approximate nominal length masses for the more common stranded rope constructions and large diameter stranded and spiral ropes are also given.

  • Standard
    79 pages
    English language
    sale 15% off

This document specifies the requirement for coating mass, other properties and testing of zinc and zinc alloy coatings on steel wire and steel wire products of circular or other section.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the requirement for coating mass, other properties and testing of zinc and zinc alloy coatings on steel wire and steel wire products of circular or other section.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies requirements for manufacture, classification, test methods, packaging, marking and issuing of a certificate for stainless-steel wire ropes. It is applicable to stainless-steel wire ropes (hereafter referred to as ropes) for instruments, mechanical transmission, cable, sling, shock absorber vibration, yacht, architecture and structure.

  • Standard
    18 pages
    English language
    sale 15% off
  • Standard
    18 pages
    French language
    sale 15% off

This document specifies the requirements relating to:
Heat-resisting alloy X6NiCrTiMnMoV26-15 (1.4944)
Softened and cold worked
Wire for forged fasteners
D ≤ 15 mm
1 100 MPa ≤ Rm ≤ 1 300 MPa
for aerospace applications.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the minimum requirements for the manufacture and testing of stranded carbon steel wire ropes for lifts, made from bright and galvanized wire finish in various constructions from 6 mm to 38 mm diameter. It is applicable to ropes used for suspension duty on traction drive and roped hydraulic lifts, and for compensation and governor duties on passenger lifts, freight lifts, service lifts, and man lifts moving between guides. It is not applicable to ropes for — builder’s hoists, — temporary hoists not running between permanent guides, — cable-ways, — mine hoists.

  • Standard
    35 pages
    English language
    sale 15% off

This document specifies the requirements relating to:
Steel X6CrNiTi18-10 (1.4541)
Air melted
Softened
Wires
0,25 mm ≤ De ≤ 3 mm
Rm ≤ 780 MPa
for aerospace application.
W.nr: 1.4541.
ASD-STAN designation: FE-PA3601.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies round non-alloy steel wires used in the manufacture of general purpose and large diameter ropes to according to ISO 2408:2017 and mine hoisting wire ropes according to ISO 3154:1988. It specifies: — the dimensional tolerances; — the mechanical characteristics; — the required conditions for any coatings; — the conditions of sampling, control and terms of acceptance. It applies to round, bright, zinc (Zn) or zinc/aluminium (Zn/Al) alloy coated wires of quality A or quality B and of nominal diameters from 0,2 mm to 7,0 mm. It does not apply to steel wire taken from manufactured ropes. It does not apply to wire for steel wire ropes for special applications, such as: — ropes for aircraft controls; — ropes for aerial ropeways; — ropes for lifts; — ropes for prestressed concrete; — ropes for conveyor belts.

  • Standard
    19 pages
    English language
    sale 15% off

This part of EN 10264 defines cold drawn non alloy steel wire used for the manufacture of:
-   ropes for general applications and lifts;
-   ropes for applications for which there is no specific European Standard.
This part of EN 10264 does not apply to steel wire taken from manufactured ropes.
This part of EN 10264 specifies the following for cold drawn non alloy steel wire for ropes for general applications:
-   dimensional tolerances;
-   mechanical characteristics;
-   requirements relating to the chemical composition of the steel wire;
-   conditions to be satisfied by any coating.
In addition to the requirements of this part of EN 10264, the requirements of EN 10264-1 also apply.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the composition, dimensions and mechanical properties of steel wire with a high mass fraction of carbon, generally brass coated, for reinforcing high-pressure hoses. It is applicable to multiple parallel wires, braided or spirally wrapped for reinforcement in a rubber or synthetic hose that is made to withstand a relatively high bursting pressure.

  • Standard
    12 pages
    English language
    sale 15% off

This part of EN 10264 defines cold drawn non alloy steel wire used for the manufacture of:
-   ropes for general applications and lifts;
-   ropes for applications for which there is no specific European Standard.
This part of EN 10264 does not apply to steel wire taken from manufactured ropes.
This part of EN 10264 specifies the following for cold drawn non alloy steel wire for ropes for general applications:
-   dimensional tolerances;
-   mechanical characteristics;
-   requirements relating to the chemical composition of the steel wire;
-   conditions to be satisfied by any coating.
In addition to the requirements of this part of EN 10264, the requirements of EN 10264-1 also apply.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the particular materials, manufacturing and testing requirements for stranded ropes for suspension, compensating and governor duties for traction drive and hydraulic lifts moving between guides and similar applications.
The particular hazards covered by this Part are identified in Clause 4.
This document does not establish requirements for information for use other than those given in Clause 7 of Part 1. Neither does it cover the requirements for ropes fitted with terminations.
Minimum breaking force values for the more common classes, sizes and grades of rope are provided in Tables 6 to 10.

  • Corrigendum
    2 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the particular materials, manufacturing and testing requirements for stranded ropes for suspension, compensating and governor duties for traction drive and hydraulic lifts moving between guides and similar applications.
The particular hazards covered by this Part are identified in Clause 4.
This document does not establish requirements for information for use other than those given in Clause 7 of Part 1. Neither does it cover the requirements for ropes fitted with terminations.
Minimum breaking force values for the more common classes, sizes and grades of rope are provided in Tables 6 to 10.

  • Corrigendum
    2 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the particular materials, manufacturing and testing requirements for stranded ropes for suspension, compensating and governor duties for traction drive and hydraulic lifts moving between guides and similar applications.
The particular hazards covered by this Part are identified in Clause 4.
This document does not establish requirements for information for use other than those given in Clause 7 of Part 1. Neither does it cover the requirements for ropes fitted with terminations.
Minimum breaking force values for the more common classes, sizes and grades of rope are provided in Tables 6 to 10.

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the type of information for use and maintenance of steel wire ropes to be provided by the rope manufacturer or to be included in the manufacturer’s handbook that accompanies a machine, piece of equipment or installation of which the steel wire rope forms a part.
The particular hazards covered by this document are identified in Clause 4.
For steel wire ropes conforming to Parts 8 and 9 used on cableway installations designed to carry persons, additional information for use and maintenance is given in EN 12927.
For steel wire rope slings, specific information on use and maintenance is given in EN 13414-2.
This document is not applicable to steel wire ropes manufactured before the date of publication of this document by CEN.

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the particular materials, manufacturing and testing requirements for stranded ropes for suspension, compensating and governor duties for traction drive and hydraulic lifts moving between guides and similar applications.
The particular hazards covered by this Part are identified in Clause 4.
This document does not establish requirements for information for use other than those given in Clause 7 of Part 1. Neither does it cover the requirements for ropes fitted with terminations.
Minimum breaking force values for the more common classes, sizes and grades of rope are provided in Tables 6 to 10.

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the requirements for the coating mass per unit area, for other properties and also for testing of zinc or zinc-alloy coatings on steel wire and steel wire products of circular or other section.

  • Standard
    15 pages
    English language
    sale 15% off
  • Standard
    15 pages
    English language
    sale 15% off

This document specifies test methods of steel cords which are used for tyre reinforcement. Dimension, process properties, mechanical properties and coating test method are all included.

  • Standard
    19 pages
    English language
    sale 15% off
  • Standard
    19 pages
    English language
    sale 15% off

This Part of this European Standard specifies the type of information for use and maintenance of steel wire ropes to be provided by the rope manufacturer or to be included in the manufacturer’s handbook that accompanies a machine, piece of equipment or installation of which the steel wire rope forms a part.
The particular hazards covered by this European Standard are identified in Clause 4.
For steel wire ropes conforming to Parts 8 and 9 used on cableway installations designed to carry persons, additional information for use and maintenance is given in EN 12927-7.
For steel wire rope slings, specific information on use and maintenance is given in EN 13414-2.
This document is not applicable to steel wire ropes manufactured before the date of publication of this document by CEN.

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 6931-1:2016 specifies the grades of stainless steels which are generally used in the cold drawn condition in the form of wire of circular cross-section up to 10,00 mm in diameter, for the production of springs and spring parts exposed to corrosive effects and sometimes to slightly increased temperatures (see Annex A).
Certain steel grades covered by ISO 16143‑2 are also used for springs, although to a much lesser extent. In these cases, the mechanical properties (tensile strength, etc.) will be agreed between purchaser and supplier. Similarly, diameters between 10,00 mm and 15,00 mm can be ordered according to the specifications of this part of ISO 6931, in which case the parties will agree upon the required mechanical characteristics.
In addition to the specifications of this part of ISO 6931, the general technical delivery requirements of ISO 404 are applicable.

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies minimum requirements for spliced eye terminations for wire rope slings. Prototype tests covering the type acceptance of splice methods are also specified in this document.

  • Standard
    15 pages
    English language
    sale 15% off
  • Standard
    15 pages
    English language
    sale 15% off

This document specifies the requirements relating to:
Steel FE-PA11
Softened and cold drawn
Wires for rivets
1 mm ≤ D ≤ 10 mm
for aerospace applications.

  • Standard
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document provides two different methods for the quantitative estimation of non-metallic content remaining adhered to the steel wire obtained from the recovery of materials from end-of-life tyres.
The pyrolysis method is considered as the reference method while the hydrostatic method is considered as an in-situ method.
This European Standard includes sample collection and the preparation of representative samples based on a sampling plan for the purpose of their characterization.
This European Standard does not cover the operational performance or fitness for use of the materials which are deemed to be a function of agreements between the manufacturer and the customer.
This European Standard does not purport to address all the safety concerns, if any, associated with its use. This European Standard does not establish appropriate safety and health practices and does not determine the applicability of regulatory limitations prior to its use.

  • Technical specification
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document provides two different methods for the quantitative estimation of non-metallic content remaining adhered to the steel wire obtained from the recovery of materials from end-of-life tyres.
The pyrolysis method is considered as the reference method while the hydrostatic method is considered as an in-situ method.
This European Standard includes sample collection and the preparation of representative samples based on a sampling plan for the purpose of their characterization.
This European Standard does not cover the operational performance or fitness for use of the materials which are deemed to be a function of agreements between the manufacturer and the customer.
This European Standard does not purport to address all the safety concerns, if any, associated with its use. This European Standard does not establish appropriate safety and health practices and does not determine the applicability of regulatory limitations prior to its use.

  • Technical specification
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the production methods, specifications, requirements, test methods, inspection rules, marks, packing, transportation and storage for pre-fabricated parallel wire strand (PPWS), which are made of hot-dip galvanized or zinc-aluminium coated high tensile steel wires described in ISO 19203.

  • Standard
    14 pages
    English language
    sale 15% off
  • Standard
    14 pages
    English language
    sale 15% off
  • Standard
    15 pages
    French language
    sale 15% off
  • Standard
    15 pages
    French language
    sale 15% off

1.1   This European Standard is applicable to round rod, round bars and wire made of stainless steels intended for cold heading and cold extrusion having a diameter up to and including:
-   25 mm for ferritic and austenitic-ferritic steels;
-   50 mm for austenitic steels;
-   100 mm for martensitic steels.
1.2   EN 10263 1 is indispensable for the application of this part of EN 10263.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day

1.1   This Part of EN 10263 is applicable to round rod and round bars and wire with a diameter up to and including 100 mm, of non-alloy and alloy steel, intended for cold heading, cold extrusion, subsequent quenching and tempering and induction hardening or flame hardening.
1.2   prEN 10263-1:2013 is indispensable for this Part of EN 10263.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day

1.1   This Part of EN 10263 specifies the general technical delivery conditions for round rod, round bars and wire for cold heading and cold extrusion made of:
a)   non alloy steels not intended for heat treatment after cold working, as specified in prEN 10263-2:2013;
b)   non alloy and alloy steels for case hardening, as specified in prEN 10263-3:2013;
c)   non alloy and alloy steels for quenching and tempering, as specified in prEN 10263-4:2013;
d)   stainless steels, as specified in prEN 10263-5:2013.
1.2   Parts 2,3 and 4 of this EN 10263 cover products having a diameter up to and including 100 mm.
Part 5 covers products having a diameter up to and including:
-   25 mm for ferritic and austenitic-ferritic steels;
-   50 mm for austenitic steels;
-   100 mm for martensitic steels.
1.3   In special cases supplementary requirements or deviations with respect to this European Standard may be agreed between the purchaser and the supplier at the time of enquiry and order (See Annex A).
1.4   The general technical delivery conditions in EN 10021 also apply to products supplied in accordance with this European Standard

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day

1.1   This Part of EN 10263 is applicable to round rod and bars and wire with a diameter up to and including 100 mm, of non-alloy and alloy steel, intended for cold heading and cold extrusion without subsequent heat treatment on the final components.
1.2   prEN 10263-1:2013 is indispensable for this Part of EN 10263.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day

1.1   This Part of EN 10263 is applicable to round rod, round bars and wire with a diameter up to and including 100 mm, of non-alloy and alloy steel, intended for cold heading and cold extrusion and subsequent case hardening treatment.
1.2   prEN 10263-1:2013 is indispensable for this Part of EN 10263.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the requirements for hot-dip galvanized (hereinafter referred to as zinc coated) and zinc-aluminium coated high tensile wires, which are widely used in parallel wire cables or semi-parallel wire cables for suspension bridges, stay bridges and other structures involving the use of parallel wires.

  • Standard
    13 pages
    English language
    sale 15% off

ISO 17832:2018 specifies the definition and requirements of non-parallel steel wire and cords for tyre reinforcement.

  • Standard
    18 pages
    English language
    sale 15% off
  • Standard
    18 pages
    English language
    sale 15% off

ISO 16120-1:2017 series is applicable to wire rod of non-alloy steel intended for wire drawing and/or cold rolling. The cross-section can be circular, oval, square, rectangular, hexagonal, octagonal, half-round or another shape, generally with at least 5 mm nominal dimension, and with a smooth surface.
ISO 16120-1:2017 specifies general requirements for non-alloy steel wire rod for conversion to wire. It is not applicable to products for which standards exist or are in development, for example:
-      steel wire rod intended for heat treatment;
-      free-cutting steel wire rod;
-      steel wire rod for cold heading and cold extrusion;
-      steel wire rod intended for the production of electrodes and products for welding;
-      steel wire rod for welded fabric for reinforcement for concrete;
-      steel wire rod for ball and roller bearings (see ISO 683‑17);
-      steel wire rod for wire for high fatigue strength mechanical springs, such as valve springs.
In addition to the requirements of this document, the general technical delivery requirements specified in ISO 404 apply.

  • Standard
    34 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    30 pages
    German language
    sale 10% off
    e-Library read for
    1 day

ISO 16120-4:2017 specifies requirements for wire rod for conversion to wire for special applications. It is applicable to non-alloy steel wire rod with improved characteristics intended for drawing and/or cold rolling.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    12 pages
    German language
    sale 10% off
    e-Library read for
    1 day

1.1   This Part of EN 10263 is applicable to round rod and bars and wire with a diameter up to and including 100 mm, of non-alloy and alloy steel, intended for cold heading and cold extrusion without subsequent heat treatment on the final components.
1.2   prEN 10263-1:2013 is indispensable for this Part of EN 10263.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day

1.1   This Part of EN 10263 specifies the general technical delivery conditions for round rod, round bars and wire for cold heading and cold extrusion made of:
a)   non alloy steels not intended for heat treatment after cold working, as specified in prEN 10263-2:2013;
b)   non alloy and alloy steels for case hardening, as specified in prEN 10263-3:2013;
c)   non alloy and alloy steels for quenching and tempering, as specified in prEN 10263-4:2013;
d)   stainless steels, as specified in prEN 10263-5:2013.
1.2   Parts 2,3 and 4 of this EN 10263 cover products having a diameter up to and including 100 mm.
Part 5 covers products having a diameter up to and including:
-   25 mm for ferritic and austenitic-ferritic steels;
-   50 mm for austenitic steels;
-   100 mm for martensitic steels.
1.3   In special cases supplementary requirements or deviations with respect to this European Standard may be agreed between the purchaser and the supplier at the time of enquiry and order (See Annex A).
1.4   The general technical delivery conditions in EN 10021 also apply to products supplied in accordance with this European Standard

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day

1.1   This Part of EN 10263 is applicable to round rod, round bars and wire with a diameter up to and including 100 mm, of non-alloy and alloy steel, intended for cold heading and cold extrusion and subsequent case hardening treatment.
1.2   prEN 10263-1:2013 is indispensable for this Part of EN 10263.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day

1.1   This Part of EN 10263 is applicable to round rod, round bars and wire made of stainless steels intended for cold heading and cold extrusion having a diameter up to and including:
   25 mm for ferritic and austenitic-ferritic steels;
   50 mm for austenitic steels;
   100 mm for martensitic steels
1.2   prEN 10263-1:2013 is indispensable for the application of this part of EN 10263.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day

1.1   This Part of EN 10263 is applicable to round rod and round bars and wire with a diameter up to and including 100 mm, of non-alloy and alloy steel, intended for cold heading, cold extrusion, subsequent quenching and tempering and induction hardening or flame hardening.
1.2   prEN 10263-1:2013 is indispensable for this Part of EN 10263.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 3108:2017 specifies a method of tensile test to destruction for determining the actual breaking force of steel wire ropes as given in ISO 2408. It is also applicable for other ropes, unless the International Standard concerned specifically excludes its use, or gives another method.

  • Standard
    6 pages
    English language
    sale 15% off

ISO 16120-2:2017 is applicable to general purpose steel wire rod for drawing and/or cold rolling.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    10 pages
    German language
    sale 10% off
    e-Library read for
    1 day

This document specifies requirements for wire rod for conversion to wire for special applications. It is
applicable to non-alloy steel wire rod with improved characteristics intended for drawing and/or cold
rolling.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    12 pages
    German language
    sale 10% off
    e-Library read for
    1 day

The ISO 16120 series is applicable to wire rod of non-alloy steel intended for wire drawing and/or cold
rolling. The cross-section can be circular, oval, square, rectangular, hexagonal, octagonal, half-round or
another shape, generally with at least 5 mm nominal dimension, and with a smooth surface.
This document specifies general requirements for non-alloy steel wire rod for conversion to wire. It is
not applicable to products for which standards exist or are in development, for example:
— steel wire rod intended for heat treatment;
— free-cutting steel wire rod;
— steel wire rod for cold heading and cold extrusion;
— steel wire rod intended for the production of electrodes and products for welding;
— steel wire rod for welded fabric for reinforcement for concrete;
— steel wire rod for ball and roller bearings (see ISO 683-17);
— steel wire rod for wire for high fatigue strength mechanical springs, such as valve springs.
In addition to the requirements of this document, the general technical delivery requirements specified
in ISO 404 apply.

  • Standard
    34 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    30 pages
    German language
    sale 10% off
    e-Library read for
    1 day

ISO 2408:2017 specifies requirements for the manufacture, testing, acceptance, packing, marking and issuing of a certificate of quality of wire ropes. It is applicable to round strand ropes and compacted strand ropes made from wires ropes that are uncoated (bright), zinc-coated or Zn-Al coated. It is not applicable to ropes for - mining purposes, - aircraft control, - aerial ropeways and funiculars, and - lifts.

  • Standard
    50 pages
    English language
    sale 15% off