77.140.75 - Steel pipes and tubes for specific use
ICS 77.140.75 Details
Steel pipes and tubes for specific use
Stahlhohlprofile
Canalisation et tubes en acier pour usage spécifique
Jeklene cevi in cevni profili za posebne namene
General Information
e-Library Subscription
Create subscription and get permanent access to documents within 77.140.75 - Steel pipes and tubes for specific use
Currently subscription includes documents marked with .We are working on making all documents available within the subscription.
This document specifies the technical delivery conditions for corrosion-resistant alloy seamless tubular products for casing, tubing, coupling stock and accessory material (including coupling stock and accessory material from bar) for two product specification levels:
PSL-1, which is the basis of this document;
PSL-2, which provides additional requirements for a product that is intended to be both corrosion and cracking resistant for the environments and qualification method specified in Annex G and in the ISO 15156 series.
At the option of the manufacturer, PSL-2 products can be provided in lieu of PSL-1.
NOTE 1 The corrosion-resistant alloys included in this document are special alloys in accordance with ISO 4948-1 and ISO 4948-2.
NOTE 2 For the purpose of this document, NACE MR0175 is equivalent to the ISO 15156 series.
NOTE 3 Accessory products can be manufactured from coupling stock and tubular material, or from solid bar stock or from bored and heat heat-treated bar stock as covered in Annex F.
This document contains no provisions relating to the connection of individual lengths of pipe. This document contains provisions relating to marking of tubing and casing after threading. This document is applicable to the following five groups of products:
a) group 1, which is composed of stainless alloys with a martensitic or martensitic/ferritic structure;
b) group 2, which is composed of stainless alloys with a ferritic-austenitic structure, such as duplex and super-duplex stainless alloy;
c) group 3, which is composed of stainless alloys with an austenitic structure (iron base);
d) group 4, which is composed of nickel-based alloys with an austenitic structure (nickel base);
e) group 5, which is composed of bar only (Annex F) in age-hardened (AH) nickel-based alloys with austenitic structure.
NOTE 4 Not all PSL-1 categories and grades can be made cracking resistant in accordance with the ISO 15156 series and are, therefore, not included in PSL-2.
- Standard130 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the technical delivery conditions for corrosion-resistant alloy seamless products for casing, tubing, coupling stock and accessory material (including coupling stock and accessory material from bar) for two product specification levels:
PSL-1, which is the basis of this document;
PSL-2, which provides additional requirements for a product that is intended to be both corrosion and cracking resistant for the environments and qualification method specified in Annex G and in the ISO 15156 series or NACE MR0175.
This document contains no provisions relating to the connection of individual lengths of pipe. Demonstration of conformance to ISO 15156-3:2020 or NACE MR0175-2021 of material affected by end sizing, connection manufacture or welding operations is outside the scope of this document.
This document contains provisions relating to marking of tubing and casing after threading.
This document is applicable to the following five groups of products:
a) group 1, which is composed of stainless alloys with a martensitic or martensitic/ferritic structure;
b) group 2, which is composed of stainless alloys with a ferritic-austenitic structure, such as duplex and super-duplex stainless alloy;
c) group 3, which is composed of stainless alloys with an austenitic structure (iron base);
d) group 4, which is composed of nickel-based alloys with an austenitic structure (nickel base);
e) group 5, which is composed of bar only (Annex F) in age-hardened (AH) nickel-based alloys with austenitic structure.
- Standard130 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the technical delivery conditions for welded tubes, of square and rectangular cross section, made from stainless steels, for mechanical and structural engineering and decorative use.
- Standard33 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the technical delivery conditions for welded tubes, of square and rectangular cross section, made from stainless steels, for mechanical and structural engineering and decorative use.
- Standard33 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the requirements for material, design, manufacture, testing, marking and documentation of stainless steel pliable corrugated gas tubing kits for gas installation pipework with a maximum allowable pressure (PS):
- less than or equal to 0,5 bar within a nominal size range from DN 10 to DN 50 (class 1); and
- less than or equal to 2 bar within a nominal size range from DN 10 to DN 25 (class 2).
This document applies to stainless steel pliable corrugated gas tubing kits used for 1st, 2nd and 3rd family gases (see EN 437) in residential, commercial and industrial gas installations to be installed outdoors or indoors at a temperature range from –20 °C to +60 °C.
This document does not apply to:
- pliable tubing without cover;
- corrugated safety metal hose assemblies for connection to moveable appliances.
NOTE This document does not cover the installation aspects of stainless steel pliable corrugated gas tubing kits.
- Standard47 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the technical delivery conditions in two test categories for seamless tubes of circular cross section, with specified elevated temperature properties, made of non-alloy and alloy steel.
This Part of EN 10216 is also be applied for tubes of non-circular cross section; necessary modification will be agreed at the time of enquiry and order.
- Standard51 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the technical delivery conditions in two test categories for seamless tubes of circular cross section, with specified elevated temperature properties, made of non-alloy and alloy steel.
This Part of EN 10216 is also be applied for tubes of non-circular cross section; necessary modification will be agreed at the time of enquiry and order.
- Standard51 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the requirements for design, manufacture and installation of corrugated metal hose assemblies for pressure applications, i.e. maximum allowable pressure PS greater than 0,5 bar.
- Standard87 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the requirements for steel products used for industrial piping and supports.
For some metallic materials other than steel, such as spheroidal graphite cast iron, aluminium, nickel, copper, titanium, requirements are or will be formulated in separate parts of this document.
For metallic materials which are not covered by a harmonized material standard and are not likely to be in near future, specific rules are given in this part or the above cited parts of this document.
- Standard85 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the requirements for fabrication and installation of piping systems, including supports, designed in accordance with EN 13480-3:2024.
- Standard49 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the requirements for industrial piping systems and supports, including safety systems, made of metallic materials with a view to ensure safe operation. This European Standard is applicable to metallic piping above ground, ducted or buried, irrespective of pressure.
- Standard14 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the requirements for inspection and testing of industrial piping as specified in EN 13480-1:2024 to be performed on individual spools or piping systems, including supports, designed in accordance with EN 13480-3:2024 and EN 13480-6:2024 (if applicable), and fabricated and installed in accordance with EN 13480-4:2024.
- Standard34 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies requirements for industrial piping systems made of aluminium and aluminium alloys in addition to the general requirements for industrial piping according to the series of standards EN 13480:2024 and CEN/TR 13480-7:2017. It specifies requirements for wrought products only.
NOTE Castings is not covered in this document.
- Standard44 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the design and calculation of industrial metallic piping systems, including supports, covered by EN 13480 series.
- Standard383 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies requirements for industrial piping either totally buried or partly buried and partly run in sleeves or similar protection. It is used in conjunction with the other six parts of
EN 13480:2024 series.
Where buried piping subject to this standard connects to piping installed under other jurisdiction such as pipelines, the transition can be made at a closing element e.g. an isolating or regulating valve separating the two sections. This can be close to the boundary of the industrial site, but can be inside or outside the boundary.
Operating temperature up to 75 °C.
NOTE For higher temperatures reference can be made to EN 13941-1:2019+A1:2021 and EN 13941 1:2019+A1:2021, but it is kept in mind, that CEN/TC 107 only deals with pre-insulated piping with temperatures up to 140 °C and diameters up to 800 mm, which is state of the art for these products.
- Standard36 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the technical delivery conditions for corrosion-resistant alloy seamless products for casing, tubing, coupling stock and accessory material (including coupling stock and accessory material from bar) for two product specification levels: PSL-1, which is the basis of this document; PSL-2, which provides additional requirements for a product that is intended to be both corrosion and cracking resistant for the environments and qualification method specified in Annex G and in the ISO 15156 series or NACE MR0175. This document contains no provisions relating to the connection of individual lengths of pipe. Demonstration of conformance to ISO 15156-3:2020 or NACE MR0175-2021 of material affected by end sizing, connection manufacture or welding operations is outside the scope of this document. This document contains provisions relating to marking of tubing and casing after threading. This document is applicable to the following five groups of products: a) group 1, which is composed of stainless alloys with a martensitic or martensitic/ferritic structure; b) group 2, which is composed of stainless alloys with a ferritic-austenitic structure, such as duplex and super-duplex stainless alloy; c) group 3, which is composed of stainless alloys with an austenitic structure (iron base); d) group 4, which is composed of nickel-based alloys with an austenitic structure (nickel base); e) group 5, which is composed of bar only (Annex F) in age-hardened (AH) nickel-based alloys with austenitic structure.
- Standard121 pagesEnglish languagesale 15% off
- Standard131 pagesFrench languagesale 15% off
This document specifies the requirements for seal coatings for factory application to the surfaces of cement mortar linings, which are factory applied to the interior of ductile iron pipes and fittings. It provides the performance requirements for short-term sealing efficiency, long-term durability and cyclic pressure, as well as the routine testing requirements for visual appearance, coating thickness and adhesion. This document is applicable to products for potable and irrigation water and for other applications as per agreement between manufacturer and customer.
- Standard18 pagesEnglish languagesale 15% off
This document specifies the nature, the method of application, the surface condition, performance requirements and the minimum thickness of internal linings of cement mortar for ductile iron pipes and fittings for pressure and non-pressure pipelines as defined in ISO 2531, ISO 7186 and ISO 16631. It covers cement mortar linings which are used to improve the hydraulic properties of pipes and fittings compared to un-lined pipes and fittings and/or to prevent corrosion damage and includes special requirements for linings of gravity sewers operating partially filled. It also covers linings used for the conveyance of particularly aggressive fluids, where the following solutions can be used either separately or in combination: a) an increase in the thickness of the lining; b) a change of the type of cement; c) a coating over the lining.
- Standard12 pagesEnglish languagesale 15% off
This document specifies the technical delivery conditions for welded cold sized steel tubes of circular cross section with specified outside diameter D ≤ 193,7 mm and of square and of rectangular cross section for precision applications.
This document can also be applied to welded cold sized tube with other cross section shapes.
Tubes according to this document are characterized by having precisely defined tolerances on dimensions and a specified maximum surface roughness. Typical fields of application are in the automotive, furniture and general engineering industries.
- Standard38 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the technical delivery conditions for welded cold sized steel tubes of circular cross section with specified outside diameter D ≤ 193,7 mm and of square and of rectangular cross section for precision applications.
This document can also be applied to welded cold sized tube with other cross section shapes.
Tubes according to this document are characterized by having precisely defined tolerances on dimensions and a specified maximum surface roughness. Typical fields of application are in the automotive, furniture and general engineering industries.
- Standard38 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the evaluation method of life cycle cost (LCC) and Life cycle assessment (LCA) of ductile iron pipes and fittings used for water applications and which are in compliance with EN 545.
LCC evaluation is based on concepts and methods developed in ISO 15686 5.
LCA evaluation is based on concepts and methods developed in ISO 15686 6, EN 15804:2012+A2:2019, EN ISO 14040 and EN ISO 14044.
In this document, LCA is limited to the evaluation of environmental impact due to CO2 emissions associated with the consumption of natural resources or energy and waste disposal. The other categories of impacts are not in the scope of this document.
Informative annexes are included in this document as a compilation of references, consensual factors, and scenarios with different DI pipelines.
- Standard31 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the evaluation method of life cycle cost (LCC) and Life cycle assessment (LCA) of ductile iron pipes and fittings used for water applications and which are in compliance with EN 545.
LCC evaluation is based on concepts and methods developed in ISO 15686 5.
LCA evaluation is based on concepts and methods developed in ISO 15686 6, EN 15804:2012+A2:2019, EN ISO 14040 and EN ISO 14044.
In this document, LCA is limited to the evaluation of environmental impact due to CO2 emissions associated with the consumption of natural resources or energy and waste disposal. The other categories of impacts are not in the scope of this document.
Informative annexes are included in this document as a compilation of references, consensual factors, and scenarios with different DI pipelines.
- Standard31 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies dimensions, tolerances, materials, internal and external surface characteristics, and marking of stainless steels longitudinally fusion welded tubes for the food and chemical industry.
- Standard12 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the design factor, technical requirements, test methods, installation technologies and operation advices applicable to ductile iron pipes, fittings and accessories used in piped irrigation applications. NOTE In this document, all pressures are relative pressures expressed in bars. This document also specifies materials, dimensions and tolerances, mechanical properties and standard coatings of pipes, fittings and accessories. It also gives performance requirements for all components including joints. Joint design and gasket shapes are outside the scope of this document. This document applies to pipes, fittings and accessories cast by any type of foundry process or manufactured by fabrication of cast components.
- Standard30 pagesEnglish languagesale 15% off
- Standard31 pagesFrench languagesale 15% off
This document specifies the technical delivery conditions in two test categories for welded tubes of circular cross-section made of austenitic and austenitic-ferritic stainless steel which are intended for pressure and corrosion resisting purposes at room temperature, at low temperatures or at elevated temperatures.
NOTE Once the reference of this document is published in the Official Journal of the European Union (OJEU) under Directive 2014/68/EU, pressure equipment directive, presumption of conformity to the Essential Safety Requirements (ESR) of Directive 2014/68/EU is limited to technical data of materials in this document and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of the Pressure Equipment Directive are satisfied, needs to be done by the designer of the pressure equipment, taking also into account the subsequent manufacturing processes which could affect properties of the base materials.
- Standard42 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the technical delivery conditions for steel pipes (casing, tubing and pup joints), coupling stock, coupling material and accessory material.
By agreement between the purchaser and manufacturer, this document can also be applied to other plain-end pipe sizes and wall thicknesses.
This document is applicable to the following connections:
— short round thread casing (SC);
— long round thread casing (LC);
— buttress thread casing (BC);
— non-upset tubing (NU);
— external upset tubing (EU);
— integral-joint tubing (IJ).
NOTE 1 For further information, see API Spec 5B.
For such connections, this document specifies the technical delivery conditions for couplings and thread protection.
NOTE 2 Supplementary requirements that can optionally be agreed for enhanced leak resistance connections (LC) are given in A.9 SR22.
This document can also be applied to tubulars with connections not covered by ISO or API standards.
This document is applicable to products including the following grades of pipe: H40, J55, K55, N80, L80, C90, R95, T95, P110, C110 and Q125.
This document is not applicable to threading requirements.
NOTE 3 Dimensional requirements on threads and thread gauges, stipulations on gauging practice, gauge specifications, as well as, instruments and methods for inspection of threads are given in API Spec 5B.
- Standard281 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the technical delivery conditions in two test categories for seamless tubes of a circular cross section made of austenitic (including creep resisting steel) and austenitic-ferritic stainless steel which are intended for pressure and corrosion resisting purposes at room temperature, at low temperatures or at elevated temperatures.
NOTE Once this document is published in the Official Journal of the European Union (OJEU) under Directive 2014/68/EC, presumption of conformity to the Essential Safety Requirements (ESR) of Directive 2014/68/EC is limited to technical data of materials in this document and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of the Pressure Equipment Directive are satisfied will be done by the designer or manufacturer of the pressure equipment, taking also into account the subsequent manufacturing processes which could affect properties of the base materials.
- Standard47 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies sizes and nominal working pressures for seamless and welded precision steel tubes with outside diameters in accordance with ISO 4397, and wall thicknesses and mechanical properties in accordance with ISO 3305. The nominal working pressures included in this document reflect a design factor ratio of 4 to 1 applied to the calculated burst pressures.
- Standard8 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard3 pagesEnglish languagesale 15% off
This document specifies the technical delivery conditions for steel pipes (casing, tubing and pup joints), coupling stock, coupling material and accessory material.
By agreement between the purchaser and manufacturer, this document can also be applied to other plain-end pipe sizes and wall thicknesses.
This document is applicable to the following connections:
— short round thread casing (SC);
— long round thread casing (LC);
— buttress thread casing (BC);
— non-upset tubing (NU);
— external upset tubing (EU);
— integral-joint tubing (IJ).
NOTE 1 For further information, see API Spec 5B.
For such connections, this document specifies the technical delivery conditions for couplings and thread protection.
NOTE 2 Supplementary requirements that can optionally be agreed for enhanced leak resistance connections (LC) are given in A.9 SR22.
This document can also be applied to tubulars with connections not covered by ISO or API standards.
This document is applicable to products including the following grades of pipe: H40, J55, K55, N80, L80, C90, R95, T95, P110, C110 and Q125.
This document is not applicable to threading requirements.
NOTE 3 Dimensional requirements on threads and thread gauges, stipulations on gauging practice, gauge specifications, as well as, instruments and methods for inspection of threads are given in API Spec 5B.
- Standard281 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the technical delivery conditions in two test categories for welded tubes of circular cross-section made of austenitic and austenitic-ferritic stainless steel which are intended for pressure and corrosion resisting purposes at room temperature, at low temperatures or at elevated temperatures.
NOTE Once the reference of this document is published in the Official Journal of the European Union (OJEU) under Directive 2014/68/EU, pressure equipment directive, presumption of conformity to the Essential Safety Requirements (ESR) of Directive 2014/68/EU is limited to technical data of materials in this document and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of the Pressure Equipment Directive are satisfied, needs to be done by the designer of the pressure equipment, taking also into account the subsequent manufacturing processes which could affect properties of the base materials.
- Standard42 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the technical delivery conditions in two test categories for seamless tubes of a circular cross section made of austenitic (including creep resisting steel) and austenitic-ferritic stainless steel which are intended for pressure and corrosion resisting purposes at room temperature, at low temperatures or at elevated temperatures.
NOTE Once this document is published in the Official Journal of the European Union (OJEU) under Directive 2014/68/EC, presumption of conformity to the Essential Safety Requirements (ESR) of Directive 2014/68/EC is limited to technical data of materials in this document and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of the Pressure Equipment Directive are satisfied will be done by the designer or manufacturer of the pressure equipment, taking also into account the subsequent manufacturing processes which could affect properties of the base materials.
- Standard47 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the technical delivery conditions for high strength and weather resistant electric welded and submerged arc welded cold formed steel structural hollow sections of circular, square, rectangular or elliptical forms and formed cold without subsequent heat treatment other than the heat treatment of the weld line.
NOTE 1 The requirements for tolerances, dimensions and sectional properties can be found in EN 10219 2.
NOTE 2 The attention of users is drawn to the fact that whilst cold formed grades in this document can have equivalent mechanical properties to hot-finished grades in EN 10210 3, the sectional properties of square and rectangular hollow sections in EN 10219 2 and EN 10210 2 are not equivalent.
NOTE 3 A range of steel grades is specified in this document and the user can select the grade most appropriate to the intended use and service conditions. The grades and mechanical properties, but not the final supply condition of cold formed hollow sections are generally comparable with those in EN 10025 3, EN 10025 4, EN 10025 5, EN 10025 6, EN 10149 2 and EN 10149 3.
- Standard43 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard43 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies technical delivery conditions for high strength and weather resistant hot-finished seamless, electric welded and submerged arc welded steel structural hollow sections of circular, square, rectangular or elliptical forms.
It applies to hollow sections formed hot, with or without subsequent heat treatment, or formed cold with subsequent heat treatment above 580 °C to obtain equivalent mechanical properties to those obtained in the hot formed product.
NOTE 1 The requirements for tolerances, dimensions and sectional properties are specified in EN 10210-2.
NOTE 2 The attention of users is drawn to the fact that whilst cold formed grades in EN 10219-3 can have equivalent mechanical properties to hot-finished grades in this document the sectional properties of square and rectangular hollow sections in EN 10210-2 and EN 10219-2 are not equivalent.
NOTE 3 A range of material grades is specified in this document and the user can select the grade most appropriate to the intended use and service conditions. The grades and mechanical properties of the finished hollow sections are generally comparable with those in EN 10025-4, EN 10025-5 and EN 10025-6.
NOTE 4 The requirements for seamless and welded steel structural hollow sections for use in offshore structures are covered in the EN 10225 series.
NOTE 5 Spiral welded hollow sections are expected to be used with caution in applications involving dynamic behaviour (fatigue stress) as, up to now, there is insufficient data regarding their performance.
- Standard43 pagesEnglish languagesale 10% offe-Library read for1 day
- Amendment7 pagesEnglish languagesale 10% offe-Library read for1 day
- Amendment7 pagesEnglish languagesale 10% offe-Library read for1 day
- Amendment7 pagesEnglish languagesale 10% offe-Library read for1 day
- Amendment7 pagesEnglish languagesale 10% offe-Library read for1 day
- Amendment7 pagesEnglish languagesale 10% offe-Library read for1 day
- Amendment7 pagesEnglish languagesale 10% offe-Library read for1 day
- Amendment7 pagesEnglish languagesale 10% offe-Library read for1 day
- Amendment7 pagesEnglish languagesale 10% offe-Library read for1 day
- Amendment7 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies technical delivery conditions for high strength and weather resistant hot-finished seamless, electric welded and submerged arc welded steel structural hollow sections of circular, square, rectangular or elliptical forms.
It applies to hollow sections formed hot, with or without subsequent heat treatment, or formed cold with subsequent heat treatment above 580 °C to obtain equivalent mechanical properties to those obtained in the hot formed product.
NOTE 1 The requirements for tolerances, dimensions and sectional properties are specified in EN 10210-2.
NOTE 2 The attention of users is drawn to the fact that whilst cold formed grades in EN 10219-3 can have equivalent mechanical properties to hot-finished grades in this document the sectional properties of square and rectangular hollow sections in EN 10210-2 and EN 10219-2 are not equivalent.
NOTE 3 A range of material grades is specified in this document and the user can select the grade most appropriate to the intended use and service conditions. The grades and mechanical properties of the finished hollow sections are generally comparable with those in EN 10025-4, EN 10025-5 and EN 10025-6.
NOTE 4 The requirements for seamless and welded steel structural hollow sections for use in offshore structures are covered in the EN 10225 series.
NOTE 5 Spiral welded hollow sections are expected to be used with caution in applications involving dynamic behaviour (fatigue stress) as, up to now, there is insufficient data regarding their performance.
- Standard43 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the technical delivery conditions for high strength and weather resistant electric welded and submerged arc welded cold formed steel structural hollow sections of circular, square, rectangular or elliptical forms and formed cold without subsequent heat treatment other than the heat treatment of the weld line.
NOTE 1 The requirements for tolerances, dimensions and sectional properties can be found in EN 10219 2.
NOTE 2 The attention of users is drawn to the fact that whilst cold formed grades in this document can have equivalent mechanical properties to hot-finished grades in EN 10210 3, the sectional properties of square and rectangular hollow sections in EN 10219 2 and EN 10210 2 are not equivalent.
NOTE 3 A range of steel grades is specified in this document and the user can select the grade most appropriate to the intended use and service conditions. The grades and mechanical properties, but not the final supply condition of cold formed hollow sections are generally comparable with those in EN 10025 3, EN 10025 4, EN 10025 5, EN 10025 6, EN 10149 2 and EN 10149 3.
- Standard43 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard43 pagesEnglish languagesale 10% offe-Library read for1 day
- Amendment7 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies sizes and nominal working pressures for seamless and welded precision steel tubes with outside diameters in accordance with ISO 4397, and wall thicknesses and mechanical properties in accordance with ISO 3305. The nominal working pressures included in this document reflect a design factor ratio of 4 to 1 applied to the calculated burst pressures.
- Standard8 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard3 pagesEnglish languagesale 15% off
- Standard1 pageEnglish languagesale 15% off
- Standard1 pageFrench languagesale 15% off
- Standard1 pageEnglish languagesale 15% off
- Standard1 pageFrench languagesale 15% off
- Standard1 pageEnglish languagesale 15% off
- Standard1 pageFrench languagesale 15% off
- Standard1 pageEnglish languagesale 15% off
- Standard1 pageFrench languagesale 15% off