77.150.10 - Aluminium products
ICS 77.150.10 Details
Aluminium products
Aluminiumprodukte
Produits en aluminium
Aluminijski izdelki
General Information
This document specifies the particular requirements for wrought aluminium and aluminium alloys in the form of circle or circle stock for general applications.
It applies to:
- Circles made out of hot or cold rolled circles stock by:
- Blanking: thickness 0,2 mm up to including 12 mm and with a diameter up to 1 000 mm;
- Sawing or shearing: thickness 0,2 mm up to and including 200 mm with a diameter up to 3 500 mm;
- Hot or cold rolled circle stock with a thickness from 0,2 mm up to and including 200 mm and with a width up to 3 500 mm.
It does not apply to slugs for impact extrusions or to circle and circle stock for culinary utensils applications which are dealt with in other European Standards.
- Standard12 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft11 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the particular requirements for wrought aluminium and aluminium alloys in the form of circle or circle stock for culinary utensils applications.
This standard is applicable to:
- Circles made out of hot or cold rolled circles stock, with a thickness from 0,2 mm up to and including 12 mm and with a diameter from 100 mm up to and including 1 600 mm.
NOTE Circles with a diameter up to 1 000 mm can be produced by blanking.
- Hot or cold-rolled circle stock with a thickness from 0,2 mm up to and including 12 mm and with a width up to 1 600 mm.
This document is not applicable to slugs for impact extrusions which are dealt with in other European Standards.
- Standard12 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft12 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies technical conditions for inspection and delivery of alloys EN AW-6060 and EN AW 6063 extruded precision profiles manufactured with and without a thermal barrier (see Figures 1 and 2) and without further surface treatment.
Precision profiles covered in this document are distinguished from extruded profiles for general applications covered in EN 755 9 by the following characteristics:
- they are designed with mostly uniformly wall thicknesses;
- they are mainly used for mechanical engineering, architectural and automotive (except crash-elements) applications;
- the maximum weight by meter is 10 kg/m;
- the maximum wall thickness proportion (Smax/Smin) is 3,5.
In the case of profiles, which, due to the complexity of their design, are difficult to manufacture and specify, special agreements between supplier and purchaser may need to be reached.
NOTE The effect of the thermal barrier material on the dimensional tolerances is covered by EN 12020 2 although the actual thermal barrier material itself is not (see EN 14024).
- Standard10 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft11 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies a method to measure the deformation of the aluminium tube body.
It is applicable to cylindrical aluminium tubes used for packing pharmaceutical, cosmetic, hygiene, food and other domestic and industrial products.
- Standard7 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft7 pagesEnglish languagesale 10% offe-Library read for1 day
This standard specifies a method for the determination of the adhesion of the internal and external protective lacquer of aluminium tubes.
It is applicable to aluminium tubes that are coated with an internal or external protective lacquer and which are used for packing, e.g. pharmaceutical, cosmetic, hygiene, food and other household products.
- Standard8 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft8 pagesEnglish languagesale 10% offe-Library read for1 day
This Part of this EN 603 specifies the tolerances on dimensions and form of wrought aluminium and aluminium alloy forging stock. It applies to extruded and rolled products.
- Standard26 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft25 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the chemical composition limits for aluminium casting alloys and mechanical properties of separately cast test pieces for these alloys.
Annex C is included as a guide to the selection of alloys for a specific use or process.
This document is intended to be used in conjunction with EN 576, EN 1559-1, EN 1559-4, EN 1676 and EN ISO 8062-3.
- Standard35 pagesEnglish languagesale 10% offe-Library read for1 day
- Amendment9 pagesEnglish languagesale 10% offe-Library read for1 day
- Amendment6 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies requirements for unfired pressure vessels and their parts made of aluminium and aluminium alloys in addition to the general requirements for unfired pressure vessels under EN 13445:2019 Parts 1 to 5. This document specifies unfired pressure vessels for loads up to 500 full cycles.
NOTE Cast materials are not included in this version. Details regarding cast materials will be subject to an amendment to or a revision of this document.
- Standard37 pagesEnglish languagesale 10% offe-Library read for1 day
- Amendment7 pagesEnglish languagesale 10% offe-Library read for1 day
- Amendment4 pagesEnglish languagesale 10% offe-Library read for1 day
This part of IEC 60317 specifies the requirements of enamelled round aluminium winding
wires of class 200 with a dual coating. The underlying coating is based on polyester or
polyesterimide resin, which can be modified provided it retains the chemical identity of the
original resin and meets all specified wire requirements. The superimposed coating is based
on polyamide-imide resin.
NOTE A modified resin is a resin that has undergone a chemical change, or contains one or more additives to
enhance certain performance or application characteristics.
The range of nominal conductor diameters covered by this document is:
– Grade 1: 0,250 mm up to and including 3,150 mm;
– Grade 2: 0,250 mm up to and including 5,000 mm.
The nominal conductor diameters are specified in Clause 4 of IEC 60317-0-3:2008 and
IEC 60317-0-3:2008/AMD1:2013.
- Standard13 pagesEnglish languagesale 10% offe-Library read for1 day
This part of IEC 60317 specifies the requirements of paper tape covered round aluminium
winding wires. This covering consists of two or more layers of paper tape and is primarily
intended for winding coils for oil immersed transformers.
The range of nominal conductor diameters covered by this document is:
– 0,500 mm up to and including 5,000 mm.
The nominal conductor diameters are specified in Clause 4 of IEC 60317-0-3:2008 and
IEC 60317-0-3:2008/AMD1:2013.
The paper tapes included in this document are restricted to those covered in IEC 60554-1 and
IEC 60554-3-5.
- Standard14 pagesEnglish languagesale 10% offe-Library read for1 day
This part of IEC 60317 specifies the requirements of paper tape covered rectangular aluminium
winding wires. This covering consists of two or more layers of paper tape and is primarily
intended for winding coils for oil immersed transformers.
The range of nominal conductor dimensions covered by this document is:
– width: min. 2,00 mm max. 16,0 mm;
– thickness: min. 0,80 mm max. 5,60 mm.
The paper tapes included in this document are restricted to those specified in IEC 60554-1 and
IEC 60554-3-5.
- Standard14 pagesEnglish languagesale 10% offe-Library read for1 day
ISO 6279:2017 specifies the composition and properties of preferred cast aluminium alloys for use in solid plain bearings. Other alloys can be specified with agreement between the manufacturer and user.
- Standard6 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard2 pagesEnglish languagesale 15% off
This European Standard defines the requirements for grades of alloyed aluminium ingots intended for remelting.
It specifies the classifications and designations applicable to these grades, the conditions in which they are produced, their properties and the marks by which they are identified.
- Standard17 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies minimum requirements for material, design, construction and workmanship, testing and examination during the manufacture of transportable refillable welded aluminium liquefied petroleum gas (LPG) cylinders, having a water capacity from 0,5 litres up to and including 150 litres, exposed to ambient temperature.
- Standard48 pagesEnglish languagesale 10% offe-Library read for1 day
This standard is applicable to flexible aluminum tubes.
This standard defines the dimensions of the tube nozzle including orifice and thread.
- Standard10 pagesEnglish languagesale 10% offe-Library read for1 day
This part of IEC 60317 specifies the general requirements of enamelled round aluminium winding wires with or without a bonding layer. The range of nominal conductor diameters is given in the relevant specification sheet. When reference is made to a winding wire according to a standard of the IEC 60317 series mentioned under Clause 2, the following information is given in the description: - reference to IEC specification; - nominal conductor diameter, in millimetres; - grade.
- Amendment6 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the chemical composition limits of wrought aluminium and wrought aluminium alloys and form of products.
NOTE The chemical composition limits of aluminium and aluminium alloys specified herein are completely identical with those registered with the Aluminium Association, 1525, Wilson Boulevard, Suite 600, Arlington, VA 22209, USA, for the corresponding alloys.
- Standard55 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies requirements for roofing and cladding products used for assembly into coverings for wall claddings, linings and pitched roofs, made from aluminium sheet with or without additional surface treatment (organic coating or anodising).
The standard establishes general characteristics, definitions and labelling of the products, together with requirements for the materials from which the products can be manufactured. It is intended to be used either by manufacturers to ensure that their products comply with the requirements or by purchasers to verify that the products comply before they are despatched from the factory. It specifies the requirements for products which enable them to meet all normal service conditions. Products can be prefabricated or semi-formed products as well as strip, coil and sheet for on-site-formed applications (e.g. standing seam roofs).
The standard applies to all discontinuously laid and fully supported roofing and cladding products made of aluminium sheets. No requirements for supporting construction, design of roof system and execution of connections and flashings are included.
The standard does not apply to self-supporting aluminium sheets that are covered by EN 508-2.
- Standard13 pagesEnglish languagesale 10% offe-Library read for1 day
This part of EN 508 specifies requirements for self-supporting external profiled sheets for roof covering wall cladding, lining and liner tray products for discontinuous laying made from aluminium sheet with or without surface treatment (additional organic coatings or anodising).
The standard establishes general characteristics, definitions, classifications and labelling for the products, together with requirements for the materials from which the products can be manufactured. It is intended to be used either by manufacturers to ensure that their products comply with the requirements or by purchasers to verify that the products comply before they are made available on the market before being despatched from the factory. It specifies the requirements for products which enable them to meet all normal service conditions.
The standard applies to all discontinuously laid self-supporting external profiled sheets for roof covering, wall cladding, lining and liner trays with the exception of tiles with a surface area less than 1 m2 and produced by stamping. These profiled roof sheets are designed to keep wind, rain and snow out of the building, and to transfer any resultant loads and infrequent maintenance loads to the structure.
This standard does not cover products for structural purposes, i.e. it does not cover products used in structural class III (according to EN 1999 1 4), it does not cover products used in constructions of Structural Classes I and II (according to EN 1999 1 4) intended to contribute to the global or partial stability of the building structure by providing racking resistance or resistance of permanent static loads (excluding self-weight of the metal sheet).
No requirements for supporting construction, design of roof system and execution of connections and flashings are included.
- Standard39 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the chemical composition limits of wrought aluminium and wrought aluminium alloys and form of products.
NOTE The chemical composition limits of aluminium and aluminium alloys specified herein are completely identical with those registered with the Aluminium Association, 1525, Wilson Boulevard, Suite 600, Arlington, VA 22209, USA, for the corresponding alloys.
- Standard55 pagesEnglish languagesale 10% offe-Library read for1 day
- Amendment4 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies requirements for roofing and cladding products used for assembly into coverings for wall claddings, linings and pitched roofs, made from aluminium sheet with or without additional surface treatment (organic coating or anodising).
This document establishes general characteristics, definitions and labelling of the products, together with requirements for the materials from which the products can be manufactured. It is intended to be used either by manufacturers to ensure that their products comply with the requirements or by purchasers to verify that the products comply before they are despatched from the factory. It specifies the requirements for products which enable them to meet all normal service conditions. Products can be prefabricated or semi-formed products as well as strip, coil and sheet for on-site-formed applications (e.g. standing seam roofs).
This document applies to all discontinuously laid and fully supported roofing and cladding products made of aluminium sheets. No requirements for supporting construction, design of roof system and execution of connections and flashings are included.
This document does not apply to self-supporting aluminium sheets that are covered by EN 508-2.
- Standard13 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the requirements relating to:
Aluminium alloy 2024-
T42
Drawn tubes for structural applications
for aerospace applications.
- Standard13 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the requirements relating to:
Aluminium 1050A-H14
Wire for solid rivets
D ≤ 10 mm
for aerospace applications.
- Standard8 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard defines the requirements for the ordering, manufacture, testing, inspection and delivery of aluminium and aluminium alloy sheet and strip, clad or unclad. It shall be applied when referred to and in conjunction with the EN material standard unless otherwise specified on the drawing, order or inspection schedule.
- Standard40 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard defines the requirements for the ordering, manufacture, testing, inspection and delivery of aluminium and aluminium alloy, bar and section, produced by extrusion, rolling or drawing. It shall be applied when referred to and in conjunction with the EN material standard unless otherwise specified on the drawing, order or inspection schedule.
- Standard37 pagesEnglish languagesale 10% offe-Library read for1 day
This International Standard is applicable to seamless steel and aluminium-alloy transportable gas cylinders
(single or those that comprise a bundle) intended for compressed and liquefied gases under pressure, of
water capacity from 0,5 l up to 150 l. It also applies, as far as practical, to cylinders of less than 0,5 l water
capacity and greater than 150 l.
This International Standard specifies the requirements for periodic inspection and testing to verify the integrity
of such gas cylinders to be re-introduced into service for a further period of time.
This International Standard does not apply to periodic inspection and maintenance of acetylene cylinders or to
the periodic inspection and testing of composite cylinders.
- Standard64 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard64 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard64 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard65 pagesGerman languagesale 10% offe-Library read for1 day
- Standard65 pagesGerman languagesale 10% offe-Library read for1 day
This European Standard applies to welded wrought aluminium and aluminium alloy enclosures pressurized with dry air, inert gases, for example sulphur hexafluoride or nitrogen or a mixture of such gases, used in indoor and outdoor installations of high-voltage switchgear and controlgear with rated voltages above 1kV, where the gas is used principally for its dielectric and/or arc-quenching properties with rated voltages.
- above 1 kV and up to and including 52 kV and with gas-filled compartments with design pressure higher than 300 kPa relative pressure (gauge);
- and with rated voltage above 52 kV.
The enclosures comprise parts of electrical equipment not necessarily limited to the following examples:
- circuit-breakers;
- switch-disconnectors;
- disconnectors;
- earthing switches;
- current transformers;
- voltage transformers;
- surge arrestors;
- busbars and connections;
- etc.
The scope also covers enclosures of pressurized components such as the centre chamber of live tank switchgear, gas-insulated current transformers, etc.
- Standard28 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard applies to welded composite enclosures of cast and wrought aluminium alloy pressurized with dry air, inert gases (e.g. sulphur hexafluoride or nitrogen or a mixture of such gases), used in indoor and outdoor installations of high-voltage switchgear and controlgear with rated voltages above 1kV, where the gas is used principally for its dielectric and/or arc-quenching properties with rated voltages
- above 1 kV and up to and including 52 kV and with gas-filled compartments with design pressure higher than 300 kPa relative pressure (gauge);
- and with rated voltage above 52 kV.
The enclosures comprise parts of electrical equipment not necessarily limited to the following examples:
- circuit-breakers;
- switch-disconnectors;
- disconnectors;
- earthing switches;
- current transformers;
- voltage transformers;
- surge arrestors;
- busbars and connections;
- etc.
The scope also covers enclosures of pressurized components such as the centre chamber of live tank switchgear, gas-insulated current transformers, etc.
- Standard16 pagesEnglish languagesale 10% offe-Library read for1 day
To expand the scope of ISO 10460:2005 to include requirements for the periodic inspection and testing of welded aluminium alloy and stainless steel cylinders and to refresh the Normative references list in order to bring it up to date.
The revision will contain requirements that apply to all cylinder types covered in the scope as well as specific requirements (possibly as Normative Annexes) for particular cylinder material types (e.g. aluminium alloys).
- Standard30 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the mechanical properties of wrought aluminium and wrought aluminium alloy sheet, strip and plate for general engineering applications.
It does not apply to semi-finished rolled products in coiled form to be subjected to further rolling (reroll stock) or to special products such as corrugated, embossed, painted, sheets and strips or to special applications such as aerospace, can stock, finstock, for which mechanical properties are specified in separate European Standards.
The chemical composition limits of the alloys are specified in EN 573 3. Temper designations are defined in EN 515.
- Standard97 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the mechanical properties of wrought aluminium and wrought aluminium alloy sheet, strip and plate for general engineering applications.
It does not apply to semi-finished rolled products in coiled form to be subjected to further rolling (reroll stock) or to special products such as corrugated, embossed, painted, sheets and strips or to special applications such as aerospace, can stock, finstock, for which mechanical properties are specified in separate European Standards.
The chemical composition limits of the alloys are specified in EN 573 3. Temper designations are defined in EN 515.
- Standard97 pagesEnglish languagesale 10% offe-Library read for1 day
This part of IEC 60317 specifies the requirements of enamelled rectangular aluminium
winding wire of class 180 with a sole coating based on polyesterimide resin, which can be
modified providing it retains the chemical identity of the original resin and meets all specified
wire requirements.
NOTE A modified resin is a resin that has undergone a chemical change, or contains one or more additives to
enhance certain performance or application characteristics.
The range of nominal conductor dimensions covered by this standard is:
– width: min. 2,0 mm max. 16,0 mm;
– thickness: min. 0,80 mm max. 5,60 mm.
Wires of grade 1 and grade 2 are included in this specification and apply to the complete
range of conductors.
The specified combinations of width and thickness as well as the specified width/thickness
ratio are given in IEC 60317-0-9:2015.
- Standard12 pagesEnglish languagesale 10% offe-Library read for1 day
This part of IEC 60317 specifies the requirements of enamelled rectangular aluminium
winding wire of class 200 with a dual coating. The underlying coating is based on polyester or
polyesterimide resin, which can be modified providing it retains the chemical identity of the
original resin and meets all specified wire requirements. The superimposed coating is based
on polyamide-imide resin.
NOTE A modified resin is a resin that has undergone a chemical change, or contains one or more additives to
enhance certain performance or application characteristics.
The range of nominal conductor dimensions covered by this standard is:
– width: min. 2,0 mm max. 16,0 mm;
– thickness: min. 0,80 mm max. 5,60 mm.
Wires of grade 1 and grade 2 are included in this specification and apply to the complete
range of conductors.
The specified combinations of width and thickness as well as the specified width/thickness
ratio are given in IEC 60317-0-9:2015.
- Standard12 pagesEnglish languagesale 10% offe-Library read for1 day
This Part of EN 13480 specifies requirements for industrial piping systems made of aluminium and aluminium alloys in addition to the general requirements for industrial piping according to the series of standards EN 13480 and CEN/TR 13480-7.
- Standard45 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the grades and the corresponding requirements for magnesium alloys for cast anodes.
This European Standard specifies 2 groups of cast magnesium alloy grades by a classification based on chemical composition. The first group deals with magnesium alloy ingots for anodes. The second group deals with magnesium alloy anode castings.
This European Standard specifies chemical composition, designation, testing and inspection documentation.
This European Standard does not cover technical delivery conditions for magnesium alloy anode castings (see EN 1559-1 [3] and EN 1559-5 [4]).
- Standard18 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard is applicable for internally coated cylindrical and conical aluminium tubes, mainly used for the packing of pharmaceutical, cosmetic, hygiene, food or other household products.
The internal coating is used as a barrier and should avoid any contact between aluminium and the product. This European Standard defines the sodium chloride method to detect the electrolyte conductivity as one criterion for the quality of the internal coating.
NOTE The electrolyte conductivity of the internal coating is only one criterion for evaluation of the quality of an internal coating. It does not give any information on the quantity or size of any pores or uncoated areas, nor any hint on possible reactions between the aluminium tube and the product. The electrolyte conductivity is never used as the sole criterion for quality evaluation of the internal coating, but always with other parameters, e.g. film thickness, acetone and/or ammonia resistance and of course results of enhanced stability studies.
- Standard8 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard is applicable for internally coated cylindrical aluminium tubes, mainly used for the packing of pharmaceutical, cosmetic, hygiene, food or other household products.
The internal coating is used as a barrier and should avoid any contact between aluminium and the product. This European Standard defines the copper sulphate method to detect the electrolyte conductivity as one criterion for the quality of the internal coating.
NOTE The electrolyte conductivity of the internal coating is only one criterion for evaluation of the quality of an internal coating. It does not give any information on the quantity or size of any pores or uncoated areas, nor any hint on possible reactions between the aluminium tube and the product. The electrolyte conductivity is never used as the sole criterion for quality evaluation of the internal coating, but always with other parameters, e.g. film thickness, acetone and/or ammonia resistance and of course results of enhanced stability studies.
- Standard8 pagesEnglish languagesale 10% offe-Library read for1 day
TThis European Standard specifies the dimensions and volumes for one-piece aluminium aerosol containers with a 25,4 mm aperture in relation to the capacities fixed by European Directive 80/232/EEC [2].
This standard applies to one-piece containers of monobloc construction with an ogival, spherical or flat shoulder.
- Standard11 pagesEnglish languagesale 10% offe-Library read for1 day
This part of IEC 60317 specifies the requirements of enamelled rectangular aluminium
winding wire of class 105 with a sole coating based on polyvinyl acetal resin, which may be
modified providing it retains the chemical identity of the original resin and meets all specified
wire requirements.
NOTE A modified resin is a resin that has undergone a chemical change, or contains one or more additives to
enhance certain performance of application characteristics.
Wires of grade 1 and grade 2 are included in this part of IEC 60317 and apply to the complete
range of conductors.
The specified combinations of width and thickness as well as the specific ratio width/thickness
are given in IEC 60317-0-9.
- Standard13 pagesEnglish languagesale 10% offe-Library read for1 day
This part of IEC 60317 specifies the requirements of enamelled rectangular aluminium
winding wire of class 120 with a sole coating based on polyvinyl acetal resin, which may be
modified providing it retains the chemical identity of the original resin and meets all specified
wire requirements.
NOTE A modified resin is a resin that has undergone a chemical change, or contains one or more additives to
enhance certain performance of application characteristics.
Wires of grade 1 and grade 2 are included in this part of IEC 60317 and apply to the complete
range of conductors.
The specified combinations of width and thickness as well as the specific ratio width/thickness
are given in IEC 60317-0-9.
- Standard13 pagesEnglish languagesale 10% offe-Library read for1 day
This part of IEC 60317 specifies the requirements of enamelled rectangular aluminium
winding wire of class 220 with a dual coating. The underlying coating is based on polyester or
polyesterimide resin, which may be modified providing it retains the chemical identity of the
original resin and meets all specified wire requirements. The superimposed coating is based
on polyamide-imide resin.
NOTE A modified resin is a resin that has undergone a chemical change, or contains one or more additives to
enhance certain performance of application characteristics.
Wires of grade 1 and grade 2 are included in this part of IEC 60317 and apply to the complete
range of conductors.
The specified combinations of width and thickness as well as the specific ratio width/thickness
are given in IEC 60317-0-9.
- Standard12 pagesEnglish languagesale 10% offe-Library read for1 day
TC request to delete an unnecessary and confusing Figure in publication
- Corrigendum2 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard establishes temper designation for all forms of wrought aluminium and aluminium alloys and to continuously cast aluminium alloy drawing stock and strip intended to be wrought.
- Standard25 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the technical delivery conditions relating to armour plates in weldable aluminium alloy with a nominal thickness between 10 mm and 70 mm.
For thickness below 10 mm, other specifications may be applied.
- Standard17 pagesEnglish languagesale 10% offe-Library read for1 day
TC request to delete an unnecessary and confusing Figure in publication
- Corrigendum2 pagesEnglish languagesale 10% offe-Library read for1 day
ISO 6279:2017 specifies the composition and properties of preferred cast aluminium alloys for use in solid plain bearings. Other alloys can be specified with agreement between the manufacturer and user.
- Standard6 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard2 pagesEnglish languagesale 15% off
This standard applies to cast aluminium alloy enclosures pressurized with dry air, inert gases, for example sulphur hexafluoride or nitrogen or a mixture of such gases, used in indoor or outdoor installations of high-voltage switchgear and controlgear above 1 kV, where the gas is used principally for its dielectric and/or arc-quenching properties with rated voltages
- above 1 kV and up to and including 52 kV and with gas-filled compartments with design pressure higher than 300 kPa relative pressure (gauge);
- and with rated voltage above 52 kV.
The enclosures comprise parts of electrical equipment not necessarily limited to the following examples:
- Circuit-breakers;
- Switch-disconnectors;
- Disconnectors;
- Earthing switches;
- Current transformers;
- Voltage transformers;
- Surge arrestors;
- Busbars and connections;
- etc.
The scope also covers enclosures of pressurized components such as the centre chamber of live tank switchgear, gas-insulated current transformers, etc.
- Standard26 pagesEnglish languagesale 10% offe-Library read for1 day