This document gives the safety requirements and measures for edge banding machines fed by chains or belts, with manual loading and unloading and maximum workpiece height capacity of 100 mm, capable of continuous production use, hereinafter referred as “machines”. It deals with all significant hazards, hazardous situations and events, listed in Annex A, relevant to the machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer; reasonably foreseeable misuse has been considered too. Also, transport, assembly, dismantling, disabling and scrapping phases are taken into account. The machines are designed to process in one pass one end (single-end machine) or both ends (double-end machine) of panels of: —   materials with similar physical characteristics to wood (see ISO 19085-1:2021, 3.2), even with a core sheet of aluminium light alloy; —   gypsum plaster boards. Edges to be applied by the machine can be made of: —   paper; —   melamine; —   plastic; —   composite materials; —   aluminium; —   light alloy; —   veneer; —   solid wood. It is also applicable to machines fitted with one or more of the following devices/working units, whose hazards have been dealt with: —   hot air banding unit; —   laser banding unit; —   infrared banding unit; —   dynamic processing units; —   sanding belt units; —   milling unit installed out of the integral enclosure at the panel side on single-end machines; —   milling unit installed out of the integral enclosure between machines halves of double-end machines; —   additional fixed or movable workpiece support along the feed; —   additional infeed workpiece support; —   additional outfeed workpiece support; —   in-feed device for transversal loading of panels in single-end machines; —   intermediate workpiece support in double-end machines; —   automatic panel returner in single-end machines; —   automatic tool changing; —   quick tool changing system; —   automatic multiple edges infeed device; —   workpiece heaters. This document does not deal with any hazards relating to: a)  systems for loading and unloading of the workpiece to a single machine other than automatic panel returner and infeed and outfeed workpiece supports (e.g. robots); b)  the combination of a single machine being used with other machines (as part of a line); c)  workpiece dividing unit installed out of the integral enclosure and/or whose tools protrude out of the integral enclosure; d)  plasma banding unit. It is not applicable to machines intended for use in potentially explosive atmosphere nor manufactured before the date of its publication.

  • Standard
    48 pages
    English language
    sale 15% off
  • Standard
    55 pages
    French language
    sale 15% off
  • Draft
    50 pages
    English language
    sale 15% off
  • Draft
    55 pages
    French language
    sale 15% off

This part of ISO 19085 gives the safety requirements and measures for stationary, manually loaded and unloaded:
-   single end tenoning machines with manual feed sliding table,
-   single end tenoning machines with mechanical feed sliding table,
-   single end tenoning and/or profiling machines with mechanical feed,
-   double end tenoning and/or profiling machines with mechanical feed, also designed to be automatically loaded/unloaded,
-   angular systems for tenoning and profiling with mechanical feed,
with maximum work-piece height capacity of 200 mm for single end machines and 500 mm for double end machines, hereinafter referred to as “machines”.
It deals with all significant hazards, hazardous situations and events relevant to machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also transport, assembly, dismantling, disabling and scrapping phases are taken into account.

  • Standard
    66 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    76 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document gives the safety requirements and measures to reduce risks arising during operation,
adjustment, maintenance, transport, assembly, dismantling, disabling and scrapping, related to
woodworking machines capable of continuous production use, hereinafter referred as “machines”.
These safety requirements and measures are those common to most of the machines, when they are
used as intended and under the conditions foreseen by the manufacturer; reasonably foreseeable
misuse has been considered too.
The machines are designed to process solid wood and material with similar physical characteristics to
wood, with hand feed or integrated feed.
This document is intended to be used in conjunction with the other parts of the ISO 19085 series,
applicable to specific machine types. The extent to which all significant hazards of a specific machine
type are covered is indicated in the specific part of the ISO 19085 series relevant to that machine type.
The hazards covered, at least partly, by the requirements of this document, are listed in Annex A.
It is not applicable to machines intended for use in potential explosive atmospheres or to machines
manufactured prior to the date of its publication.

  • Standard
    60 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document gives the safety requirements and measures for stationary, manually loaded and unloaded: — single end tenoning machines with manual feed sliding table; — single end tenoning machines with mechanical feed sliding table; — single end tenoning and/or profiling machines with mechanical feed; — double end tenoning and/or profiling machines with mechanical feed, also designed to be automatically loaded/unloaded; — angular systems for tenoning and profiling with mechanical feed; with maximum work-piece height capacity of 200 mm for single end machines and 500 mm for double end machines, hereinafter referred to as "machines". It deals with all significant hazards, hazardous situations and events as listed in Clause 4 relevant to machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also, transport, assembly, dismantling, disabling and scrapping phases are taken into account. NOTE For relevant but not significant hazards, e.g. sharp edges of the machine frame, see ISO 12100:2010. The machines are designed to process in one pass one end or two sides, either opposite or perpendicular to each other, of work-pieces made of: 1) solid wood; 2) materials with similar physical characteristics to wood (see ISO 19085-1:2017, 3.2); 3) fibre-cement, rock/glass wool, gypsum, plasterboard, only with machines with mechanical feed. It is also applicable to machines fitted with one or more of the following additional working units, whose hazards have been dealt with: — sanding units; — fixed or movable work-piece support; — automatic tool changing; — automatic work-piece returner; — glass bead saw unit; — hinge recessing unit; — post forming edge pre-cutting; — boring unit; — dynamic processing unit; — sawing unit installed out of the integral enclosure, between machine halves in double end machines; — foiling unit; — coating unit; — grooving unit with milling tool installed out of the integral enclosure, between machine halves; — brushing unit; — gluing unit; — sealing unit; — dowels inserting unit; — tongues inserting unit; — inkjet marking unit; — laser marking unit; — labelling unit; — work-piece back-up device (anti-chipping / anti-splintering device); — quick tool changing system. This document does not deal with any hazards related to: a) systems for automatic loading and unloading of the work-piece to a single machine other than automatic work-piece returner; b) single machine being used in combination with any other machine (as part of a line); c) use of tools, other than saw blades or milling tools for grooving, installed between machine halves and out of the integral enclosure in double end machines; d) use of tools protruding out of the integral enclosure; e) chemical characteristics of fibre-cement, rock/glass wool, gypsum, plasterboard and their dust. It is not applicable to machines intended for use in potentially explosive atmosphere nor to machines manufactured prior to its publication.

  • Standard
    53 pages
    English language
    sale 15% off
  • Standard
    57 pages
    French language
    sale 15% off
  • Draft
    55 pages
    English language
    sale 15% off
  • Draft
    56 pages
    English language
    sale 15% off
  • Draft
    60 pages
    French language
    sale 15% off
  • Draft
    60 pages
    French language
    sale 15% off

This document gives the safety requirements and measures to reduce risks arising during operation, adjustment, maintenance, transport, assembly, dismantling, disabling and scrapping, related to woodworking machines capable of continuous production use, hereinafter referred as "machines". These safety requirements and measures are those common to most of the machines, when they are used as intended and under the conditions foreseen by the manufacturer; reasonably foreseeable misuse has been considered too. The machines are designed to process solid wood and material with similar physical characteristics to wood, with hand feed or integrated feed. This document is intended to be used in conjunction with the other parts of the ISO 19085 series, applicable to specific machine types. The extent to which all significant hazards of a specific machine type are covered is indicated in the specific part of the ISO 19085 series relevant to that machine type. The hazards covered, at least partly, by the requirements of this document, are listed in Annex A. It is not applicable to machines intended for use in potential explosive atmospheres or to machines manufactured prior to the date of its publication.

  • Standard
    47 pages
    English language
    sale 15% off
  • Standard
    51 pages
    French language
    sale 15% off
  • Draft
    51 pages
    English language
    sale 15% off
  • Draft
    55 pages
    French language
    sale 15% off

2020-07-20 JF: Through the decision C132/2020 taken on 2020-07-08, the CEN Technical Board approved the revised Annex ZA and therefore, the European Amendment, of EN ISO 19085-10:2019. European amendment is under publication.

  • Amendment
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This international standard deals with all significant hazards, hazardous situations and events relevant to stationary multi-blade rip sawing machines, hereinafter referred to as “machines”, designed to cut solid wood and material with similar physical characteristics as wood, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also transport, assembly, dismantling, disabling and scrapping phases are taken into account.
This international standard does not apply to machines with vertical roller feed or vertical chain conveyor feed or machines designed to make the first rip cut on a log.
This international standard does not deal with specific hazards related to the combination of single machines with any other machine as part of a line.

  • Standard
    52 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This part of ISO 19085 gives the safety requirements and measures for stationary and displaceable combined woodworking machines, having at least two separately usable working units and with manual loading and unloading of the workpiece, hereinafter referred to as “machines”. The integrated working units can be only
-       a sawing unit,
-   a moulding unit and/or
-   a planing unit.
The machines are designed to cut solid wood and material with similar physical characteristics to wood.
NOTE 1   For the definitions of stationary and displaceable machines see ISO 19085-1:2017, 3.4 and 3.5.
This part of ISO 19085 deals with all significant hazards, hazardous situations and events as listed in Clause 4, relevant to the machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also, transport, assembly, dismantling, disabling and scrapping phases have been taken into account.
NOTE 2   For relevant but not significant hazards, e.g. sharp edges of the machine frame, see ISO 12100:2010.
This part of ISO 19085 does apply to machines also equipped with the devices/additional working units listed in ISO 19085-5:2017, clause 1,  ISO 19085-6: 2017, clause 1,   and ISO 19085-7: 2017, clause 1,   and ISO 19085-9: 2017, clause 1.
This part of ISO 19085 does not apply to:
a)   combined machines which consist only of a planing unit and a mortising unit;
NOTE 3   Such machines are dealt with in ISO 19085-7.
b)   combined machines incorporating a band saw unit;
c)   machines with a mortising unit with a separate drive other than the planing unit drive.
d)   machines intended for use in potentially explosive atmosphere;
e)   machines manufactured before the date of its publication as an international standard.

  • Standard
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This international standard deals with all significant hazards, hazardous situations and events as listed in Clause 4 which are relevant to stationary and displaceable circular saw benches (with or without sliding table and/or demountable power feed unit), also known as “table saws” (in the USA), hereinafter referred to as “machines”, designed to cut wood and material with similar physical characteristics to wood, when they are operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also transport, assembly, dismantling, disabling and scrapping phases are taken into account.

  • Standard
    60 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document gives the safety requirements and measures for stationary multi-blade rip sawing machines manually loaded and/or unloaded, hereinafter referred to as "machines", designed to cut solid wood and material with similar physical characteristics to wood. It deals with all significant hazards, hazardous situations and events as listed in Clause 4 relevant to machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also, transport, assembly, dismantling, disabling and scrapping phases are taken into account. NOTE For relevant but not significant hazards, e.g. sharp edges of the machine frame, see ISO 12100:2010. This document does not deal with specific hazards related to the combination of single machines with any other machine as part of a line. It is not applicable to machines: — with all saw blades spindles mounted below the workpiece support/level only; — intended for use in potentially explosive atmosphere; — manufactured prior to its publication.

  • Standard
    40 pages
    English language
    sale 15% off
  • Standard
    40 pages
    English language
    sale 15% off
  • Standard
    45 pages
    French language
    sale 15% off
  • Standard
    45 pages
    French language
    sale 15% off

This document gives the safety requirements and measures for stationary and displaceable circular saw benches (with or without sliding table and/or demountable power feed unit), also known as "table saws" (in the USA), hereinafter referred to as "machines", designed to cut wood and material with similar physical characteristics to wood.
NOTE 1 For the definition of stationary and displaceable machine, see ISO 19085‑1:2017, 3.4 and 3.5.
It deals with all significant hazards, hazardous situations and events as listed in Clause 4 relevant to these machines when they are operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also, transport, assembly, dismantling, disabling and scrapping phases are taken into account.
NOTE 2 For relevant but not significant hazards, e.g. sharp edges of the machine frame, see ISO 12100:2010.
It is also applicable to machines fitted with one or more of the following devices, or working unit, whose hazards have been dealt with:
— device for the main saw blade and scoring saw blade to be raised and lowered through the table;
— device to tilt the main saw blade and scoring saw blade for angled cutting;
— device for scoring;
— device for grooving with milling tool with a width not exceeding 20 mm in one pass;
— demountable power feed unit;
— additional manually operated sliding table;
— powered work-piece clamping device.
NOTE 3 Circular saw benches are used for ripping, cross cutting, dimensioning and grooving.
This document does not apply to:
a) transportable/displaceable machines intended for outdoor use on building sites;
NOTE 4 Building site saws (contractor saws) are covered by the requirements of ISO 19085‑10:2018.
b) hand held woodworking machines including any adaptation permitting their use in a different mode, i.e. bench mounting;
c) machines intended for use in a potentially explosive atmosphere;
d) machines manufactured before the date of its publication as an International Standard;
e) transportable machines with a maximum saw blade diameter of ≤315 mm.
NOTE 5 Transportable motor-operated electric tools are dealt with in IEC 62841‑1:2014 and IEC 62841‑3‑1:2014.

  • Standard
    60 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document gives the safety requirements and measures for stationary and displaceable combined woodworking machines, having at least two separately usable working units and with manual loading and unloading of the workpiece, hereinafter referred to as "machines". The integrated working units can be of these types only:
— a sawing unit;
— a moulding unit;
— a planing unit.
The machines are designed to cut solid wood and material with similar physical characteristics to wood.
NOTE 1 For the definitions of stationary and displaceable machines, see ISO 19085‑1:2017, 3.4 and 3.5.
This document deals with all significant hazards, hazardous situations and events as listed in Clause 4, relevant to the machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also, transport, assembly, dismantling, disabling and scrapping phases have been taken into account.
NOTE 2 For relevant but not significant hazards, e.g. sharp edges of the machine frame, see ISO 12100:2010.
This document does apply to machines also equipped with the devices/additional working units listed in the Scopes of ISO 19085‑5:2017, ISO 19085‑6:2017, ISO 19085-7:2019 and ISO 19085-9:2019.
This document does not apply to:
a) machines incorporating only a planing unit and a mortising device;
NOTE 3 Such machines are dealt with in ISO 19085-7:2019.
b) combined machines incorporating a band saw unit;
c) machines with a mortising unit with a separate drive other than the planing unit drive;
d) machines intended for use in potentially explosive atmosphere;
e) machines manufactured before the date of its publication as an International Standard.

  • Standard
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document gives the safety requirements and measures for stationary and displaceable combined woodworking machines, having at least two separately usable working units and with manual loading and unloading of the workpiece, hereinafter referred to as "machines". The integrated working units can be of these types only: — a sawing unit; — a moulding unit; — a planing unit. The machines are designed to cut solid wood and material with similar physical characteristics to wood. NOTE 1 For the definitions of stationary and displaceable machines, see ISO 19085‑1:2017, 3.4 and 3.5. This document deals with all significant hazards, hazardous situations and events as listed in Clause 4, relevant to the machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also, transport, assembly, dismantling, disabling and scrapping phases have been taken into account. NOTE 2 For relevant but not significant hazards, e.g. sharp edges of the machine frame, see ISO 12100:2010. This document does apply to machines also equipped with the devices/additional working units listed in the Scopes of ISO 19085‑5:2017, ISO 19085‑6:2017, ISO 19085-7:2019 and ISO 19085-9:2019. This document does not apply to: a) machines incorporating only a planing unit and a mortising device; NOTE 3 Such machines are dealt with in ISO 19085-7:2019. b) combined machines incorporating a band saw unit; c) machines with a mortising unit with a separate drive other than the planing unit drive; d) machines intended for use in potentially explosive atmosphere; e) machines manufactured before the date of its publication as an International Standard.

  • Standard
    27 pages
    English language
    sale 15% off
  • Standard
    29 pages
    French language
    sale 15% off

This document deals with all significant hazards, hazardous situation and events as listed in Clause 4 relevant
to stationary and displaceable
- surface planning machines,
- thickness planing machines,
- combined surface/thickness planing machines
with an integrated feed in thicknessing mode, (with or without demountable power feed unit in planing mode)
and with manual loading and unloading of the work-piece.

  • Standard
    55 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    55 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This international standard deals with all significant hazards, hazardous situations and events as listed in Clause 4 which are relevant to displaceable building site saws, hereinafter referred to as “machines”, designed to cut solid wood and material with similar characteristics to wood (see ISO 19085-1:2016), when they are operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also transport, assembly, dismantling, disabling and scrapping phases are taken into account.

  • Standard
    47 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    47 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document gives the safety requirements and measures for stationary and displaceable
— surface planing machines, also called jointers,
— thickness planing machines, also called planers or single surface planers,
— combined surface/thickness planing machines
with fixed cutterblock position, with an integrated feed in thicknessing mode, with or without demountable power feed device in planing mode and with manual loading and unloading of the work-piece, hereinafter referred to as "machines". The machines are designed to cut solid wood and material with similar physical characteristics to wood.
NOTE 1 For the definitions of stationary and displaceable machines, see ISO 19085‑1:2017, 3.4 and 3.5.
It deals with all significant hazards, hazardous situations and events as listed in Clause 4 relevant to these machines when they are operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also, transport, assembly, dismantling, disabling and scrapping phases are taken into account.
NOTE 2 For relevant but not significant hazards, e.g. sharp edges of the machine frame, see ISO 12100.
It is also applicable to surface planing machines and combined surface/thickness planing machines fitted with an optional mortising device, whose hazards have been dealt with.
This document does not apply to:
a) machines with more than one cutterblock;
b) machines with mortising unit driven by a separate motor;
c) machines where the cutterblock is adjustable for depth of cut setting in thicknessing mode;
d) machines where the conversion from planing to thicknessing mode or vice versa is achieved by mounting or demounting parts/units;
e) machines where surfacing and thicknessing can be performed on the same section of the cutterblock at the same time;
f) machines intended for use in potentially explosive atmosphere;
g) machines manufactured before the date of its publication as an international standard;
h) displaceable machines with a maximum planing width of ≤330 mm.
NOTE 3 Transportable motor-operated electric tools are dealt with in IEC 62841‑1:2014 and IEC 61029‑2‑3:1993.

  • Standard
    55 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    55 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 19085-10:2018 gives the safety requirements and measures for displaceable building site saws, designed to cut wood and materials with similar physical characteristics to wood, hereinafter referred to as "machines".
NOTE 1 For the definition of displaceable machine, see ISO 19085‑1:2017, 3.5.
ISO 19085-10:2018 deals with all significant hazards, hazardous situations and events as listed in Clause 4, relevant to the machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also, transport, assembly, dismantling, disabling and scrapping phases have been taken into account.
NOTE 2 For relevant but not significant hazards, e.g. sharp edges of the machine frame, see ISO 12100:2010.
The machine can also be fitted with a device for the saw blade to be manually raised and lowered through the table, whose hazards have been dealt with.
This document does not apply to the following:
a) machines with a maximum saw blade diameter smaller than 350 mm or greater than 500 mm;
b) hand-held woodworking machines, including any adaptation permitting their use in a different mode, i.e. bench mounting;
c) machines with a device to tilt the saw blade for angle cutting, machines with more than one saw blade rotational speed and machines equipped with a sliding table;
NOTE 3 Hand-held motor-operated electric tools are covered by IEC 62841‑1 together with IEC 62841‑2‑5.
NOTE 4 Machines with the device to tilt the saw blade for angle cutting, machines with more than one saw blade rotational speed and machines equipped with a sliding table are considered as table saws, covered by ISO 19085‑9.
ISO 19085-10:2018 is not applicable to machines intended for use in potentially explosive atmospheres or to machines manufactured prior to the date of its publication.

  • Standard
    47 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    47 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document gives the safety requirements and measures for stationary and displaceable — surface planing machines, also called jointers, — thickness planing machines, also called planers or single surface planers, — combined surface/thickness planing machines with fixed cutterblock position, with an integrated feed in thicknessing mode, with or without demountable power feed device in planing mode and with manual loading and unloading of the work-piece, hereinafter referred to as "machines". The machines are designed to cut solid wood and material with similar physical characteristics to wood. NOTE 1 For the definitions of stationary and displaceable machines, see ISO 19085‑1:2017, 3.4 and 3.5. It deals with all significant hazards, hazardous situations and events as listed in Clause 4 relevant to these machines when they are operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also, transport, assembly, dismantling, disabling and scrapping phases are taken into account. NOTE 2 For relevant but not significant hazards, e.g. sharp edges of the machine frame, see ISO 12100. It is also applicable to surface planing machines and combined surface/thickness planing machines fitted with an optional mortising device, whose hazards have been dealt with. This document does not apply to: a) machines with more than one cutterblock; b) machines with mortising unit driven by a separate motor; c) machines where the cutterblock is adjustable for depth of cut setting in thicknessing mode; d) machines where the conversion from planing to thicknessing mode or vice versa is achieved by mounting or demounting parts/units; e) machines where surfacing and thicknessing can be performed on the same section of the cutterblock at the same time; f) machines intended for use in potentially explosive atmosphere; g) machines manufactured before the date of its publication as an international standard; h) displaceable machines with a maximum planing width of ≤330 mm. NOTE 3 Transportable motor-operated electric tools are dealt with in IEC 62841‑1:2014 and IEC 61029‑2‑3:1993.

  • Standard
    43 pages
    English language
    sale 15% off
  • Standard
    46 pages
    French language
    sale 15% off

This document gives the safety requirements and measures for stationary and displaceable circular saw benches (with or without sliding table and/or demountable power feed unit), also known as "table saws" (in the USA), hereinafter referred to as "machines", designed to cut wood and material with similar physical characteristics to wood. NOTE 1 For the definition of stationary and displaceable machine, see ISO 19085‑1:2017, 3.4 and 3.5. It deals with all significant hazards, hazardous situations and events as listed in Clause 4 relevant to these machines when they are operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also, transport, assembly, dismantling, disabling and scrapping phases are taken into account. NOTE 2 For relevant but not significant hazards, e.g. sharp edges of the machine frame, see ISO 12100:2010. It is also applicable to machines fitted with one or more of the following devices, or working unit, whose hazards have been dealt with: — device for the main saw blade and scoring saw blade to be raised and lowered through the table; — device to tilt the main saw blade and scoring saw blade for angled cutting; — device for scoring; — device for grooving with milling tool with a width not exceeding 20 mm in one pass; — demountable power feed unit; — additional manually operated sliding table; — powered work-piece clamping device. NOTE 3 Circular saw benches are used for ripping, cross cutting, dimensioning and grooving. This document does not apply to: a) transportable/displaceable machines intended for outdoor use on building sites; NOTE 4 Building site saws (contractor saws) are covered by the requirements of ISO 19085‑10:2018. b) hand held woodworking machines including any adaptation permitting their use in a different mode, i.e. bench mounting; c) machines intended for use in a potentially explosive atmosphere; d) machines manufactured before the date of its publication as an International Standard; e) transportable machines with a maximum saw blade diameter of ≤315 mm. NOTE 5 Transportable motor-operated electric tools are dealt with in IEC 62841‑1:2014 and IEC 62841‑3‑1:2014.

  • Standard
    48 pages
    English language
    sale 15% off
  • Standard
    50 pages
    French language
    sale 15% off

This document deals with all significant hazards, hazardous situations and events as listed in Clause 4, relevant for chip and dust extraction systems for indoor use designated to be connected to machines designed to cut solid wood (including hard wood), wood based materials and materials similar to wood, when they are used as intended and under the conditions foreseen by the manufacturer, including reasonably foreseeable misuse.
This European standard does not apply to:
a) extraction systems with a nominal volume flow rate V. above 8 000 m³/h and/or a volume of the dust loaded part of the dust extractor above 3,5 m³;
b) vacuum cleaners according to EN 60335-2-69/A2:2013;
c) extraction systems with fans installed in the dust loaded part;
d) extraction equipment (e. g. extraction hoods, ducts) within a woodworking machine, i. e. up to and including the outlet to which the extraction system is connected;
e) extraction systems designed for dust with KST values above 200 bar ms-1, minimum ignition energy below 10 mJ and/or lower explosion level below 30 g/m³;
f) extraction systems designed for aspiration of explosive atmospheres, e. g. dust load > 50 % lower explosion level;
g) systems designed for extraction from machines with a higher risk of causing ignition sources;
h) silos.
This European Standard is not applicable to machines which are manufactured before the date of its publication as EN.

  • Standard
    36 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This international standard deals with all significant hazards, hazardous situations and events as listed in
Clause 4 which are relevant to manually loaded and unloaded vertical panel sawing machines (with or without
integrated feed) hereinafter referred to as "machines" when they are operated, adjusted and maintained as
intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse.
Also transport, assembly, dismantling, disabling and scrapping phases are taken into account.

  • Standard
    42 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document deals with all significant hazards, hazardous situations and events as listed in Clause 4, relevant for chip and dust extraction systems for indoor use designated to be connected to woodworking machines, when they are used as intended and under the conditions foreseen by the manufacturer, including reasonably foreseeable misuse.
This document does not apply to:
a)   extraction systems with a nominal volume flow rate above 8 000 m3 h−1 and/or a volume of the dust loaded part of the dust extractor above 3,5 m3;
b)   vacuum cleaners according to EN 60335-2-69;
c)   extraction systems with fans installed in the dust loaded part;
d)   extraction equipment (e.g. extraction hoods, ducts) within a woodworking machine, i.e. up to and including the outlet to which the extraction system is connected;
e)   extraction systems designed for dust with KST values above 200 bar ms−1, minimum ignition energy below 10 mJ and/or lower explosion level below 30 g m−3;
f)   extraction systems designed for aspiration of explosive atmospheres, e.g. dust load > 50 % lower explosion level;
g)   systems designed for extraction of machines with a higher risk of causing ignition sources.
This document is not applicable to machines which are manufactured before the date of its publication as a European Standard.

  • Standard
    36 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 19085-4:2018 gives the safety requirements and measures for manually loaded and unloaded stationary vertical panel sawing machines, hereinafter referred to as "machines".
NOTE 1 In manual loading, the operator puts the work-piece directly onto the work-piece support, with no intermediate loading device to receive and transfer the work-piece from the operator to the cutting position. In manual unloading, the operator removes the work-piece directly from the work-piece support, with no intermediate unloading device to transfer the work-piece from the cutting position to the operator.
ISO 19085-4:2018 deals with all significant hazards, hazardous situations and events as listed in Clause 4 relevant to machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also, transport, assembly, dismantling, disabling and scrapping phases are taken into account.
NOTE 2 For relevant but not significant hazards, e.g. sharp edges of the machine frame, see ISO 12100:2010.
ISO 19085-4:2018 is also applicable to machines fitted with one or more of the following devices/additional working units, whose hazards have been dealt with:
- an integrated feed device;
- a device for scoring;
- an angle cutting device;
- a middle support device;
- programmable end stops for parallel vertical cuts;
- a device for grooving with a width of at most 20 mm in one pass by using a milling tool; and
- a panel pusher.
The machines are designed for cutting panels consisting of:
a) solid wood;
b) material with similar physical characteristics to wood (see ISO 19085‑1:2017, 3.2);
c) composite materials with core consisting, for example, of polyurethane or mineral material laminated with light alloy;
d) polymer-matrix composite materials and reinforced thermoplastic/thermoset/elastomeric materials; and
e) gypsum boards, gypsum bounded fibreboards.
ISO 19085-4:2018 does not apply to machines
- with pressure beam and saw unit mounted behind the work-piece support;
- where the guide rails on which the saw unit moves vertically are fixed on the machine frame and the horizontal cut can only be made by manually feeding the panel;
- designed to cut in vertical direction only;
- which are displaceable;
- automatically performing two or more cutting cycles in sequence;
- intended for use in potentially explosive atmosphere; and
- manufactured before the date of its publication.

  • Standard
    42 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document deals with all significant hazards, hazardous situations and events as listed in Clause 4, which are relevant to machines used to calibrate and/or to sand panels and/or linear work-pieces consisting of solid wood and material with similar physical characteristics to wood, gypsum boards and gypsum bounded fibreboards, fitted with an integrated feed and sanding belt(s) positioned over and/or under the work-piece level and working in the panel feed direction, hereinafter referred to as "machines", when they are operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Loading and/or
unloading is manual or automatic. Also transport, assembly, dismantling, disabling and scrapping phases are taken into account.

  • Standard
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document deals with the significant hazards, hazardous situations and events as listed in Clause 4 which
are relevant to stationary and displaceable hand fed single spindle vertical moulding machines (with or without
demountable power feed unit), herein after referred to as "machines", designed to cut solid wood, chip board,
fibreboard, plywood and also these materials if they are covered with plastic laminate or edgings when they
are used as intended and under the conditions foreseen by the manufacturer.

  • Standard
    66 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This international standard deals with all significant hazards, hazardous situations and events, listed in Clause
4, relevant to NC boring machines, NC routing machines and NC combined boring/routing machines (as
defined in 3.2.1), herein after referred to as "machines", designed to cut solid wood and material with similar
physical characteristics to wood, when they are operated, adjusted and maintained as intended and under the
conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also transport, assembly,
dismantling, disabling and scrapping phases have been taken into account.

  • Standard
    76 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 19085-10:2018 gives the safety requirements and measures for displaceable building site saws, designed to cut wood and materials with similar physical characteristics to wood, hereinafter referred to as "machines". NOTE 1 For the definition of displaceable machine, see ISO 19085‑1:2017, 3.5. ISO 19085-10:2018 deals with all significant hazards, hazardous situations and events as listed in Clause 4, relevant to the machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also, transport, assembly, dismantling, disabling and scrapping phases have been taken into account. NOTE 2 For relevant but not significant hazards, e.g. sharp edges of the machine frame, see ISO 12100:2010. The machine can also be fitted with a device for the saw blade to be manually raised and lowered through the table, whose hazards have been dealt with. This document does not apply to the following: a) machines with a maximum saw blade diameter smaller than 350 mm or greater than 500 mm; b) hand-held woodworking machines, including any adaptation permitting their use in a different mode, i.e. bench mounting; c) machines with a device to tilt the saw blade for angle cutting, machines with more than one saw blade rotational speed and machines equipped with a sliding table; NOTE 3 Hand-held motor-operated electric tools are covered by IEC 62841‑1 together with IEC 62841‑2‑5. NOTE 4 Machines with the device to tilt the saw blade for angle cutting, machines with more than one saw blade rotational speed and machines equipped with a sliding table are considered as table saws, covered by ISO 19085‑9. ISO 19085-10:2018 is not applicable to machines intended for use in potentially explosive atmospheres or to machines manufactured prior to the date of its publication.

  • Standard
    35 pages
    English language
    sale 15% off
  • Standard
    35 pages
    English language
    sale 15% off
  • Standard
    36 pages
    French language
    sale 15% off

ISO 19085-4:2018 gives the safety requirements and measures for manually loaded and unloaded stationary vertical panel sawing machines, hereinafter referred to as "machines". NOTE 1 In manual loading, the operator puts the work-piece directly onto the work-piece support, with no intermediate loading device to receive and transfer the work-piece from the operator to the cutting position. In manual unloading, the operator removes the work-piece directly from the work-piece support, with no intermediate unloading device to transfer the work-piece from the cutting position to the operator. ISO 19085-4:2018 deals with all significant hazards, hazardous situations and events as listed in Clause 4 relevant to machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also, transport, assembly, dismantling, disabling and scrapping phases are taken into account. NOTE 2 For relevant but not significant hazards, e.g. sharp edges of the machine frame, see ISO 12100:2010. ISO 19085-4:2018 is also applicable to machines fitted with one or more of the following devices/additional working units, whose hazards have been dealt with: - an integrated feed device; - a device for scoring; - an angle cutting device; - a middle support device; - programmable end stops for parallel vertical cuts; - a device for grooving with a width of at most 20 mm in one pass by using a milling tool; and - a panel pusher. The machines are designed for cutting panels consisting of: a) solid wood; b) material with similar physical characteristics to wood (see ISO 19085‑1:2017, 3.2); c) composite materials with core consisting, for example, of polyurethane or mineral material laminated with light alloy; d) polymer-matrix composite materials and reinforced thermoplastic/thermoset/elastomeric materials; and e) gypsum boards, gypsum bounded fibreboards. ISO 19085-4:2018 does not apply to machines - with pressure beam and saw unit mounted behind the work-piece support; - where the guide rails on which the saw unit moves vertically are fixed on the machine frame and the horizontal cut can only be made by manually feeding the panel; - designed to cut in vertical direction only; - which are displaceable; - automatically performing two or more cutting cycles in sequence; - intended for use in potentially explosive atmosphere; and - manufactured before the date of its publication.

  • Standard
    30 pages
    English language
    sale 15% off
  • Standard
    31 pages
    French language
    sale 15% off

ISO 19085-8:2017 gives the safety requirements and measures for stationary calibrating and sanding machines, with an integrated feed and one or more sanding belt units positioned above and/or below the work piece level, with manual or automatic loading and/or unloading, hereinafter referred to as "machines".
ISO 19085-8:2017 deals with all significant hazards, hazardous situations and events as listed in Clause 4, relevant to the machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer, including reasonably foreseeable misuse. Also, transport, assembly, dismantling, disabling and scrapping phases have been taken into account.
NOTE 1 For relevant but not significant hazards, e.g. sharp edges of the machine frame, see ISO 12100:2010.
ISO 19085-8:2017 is also applicable to machines fitted with one or more of the following devices/additional working units, whose hazards have been dealt with:
- transversal sanding unit;
- cleaning brushing unit;
- satining roller unit;
- disk brushing unit;
- texturing brushing roller unit;
- texturing brushing belt unit;
- cutterblock unit;
- texturing band saw unit;
- spiked roller unit;
- antistatic bars;
- conveyor directly controlled by the machine;
- additional work piece vacuum clamping device.
The machines are designed to calibrate and/or sand work pieces, in shape of panels or beams, consisting of:
a) solid wood;
b) material with similar physical characteristics to wood (see ISO 19085-1:2017, 3.2);
c) gypsum boards, gypsum bounded fibreboards;
d) composite materials with core consisting of e.g. polyurethane or mineral material;
e) composite boards made from the materials listed above;
f) all materials listed above, also already lacquered.
ISO 19085-8:2017 does not deal with hazards related to:
- specific devices other than those listed above;
- access through in-feed and out-feed openings of machines with a work piece height capacity greater than 550 mm;
- systems for automatic loading and/or unloading of the work piece to/from a single machine;
NOTE 2 Loading the machine manually includes manually placing the work piece onto a conveyor directly controlled by the machine. Unloading the machine manually includes manually removing the work piece from a conveyor directly controlled by the machine.
- interfacing of the machine with any other machine.
ISO 19085-8:2017 is not applicable to machines intended for use in potentially explosive atmosphere and to machines manufactured prior to the date of its publication.

  • Standard
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies the determination of the maximum speed for given eccentricity at clamping devices for the shank strength of milling tools with cylindrical and taper shank. It also specifies the marking of the tool. Bore mounted tools which are mounted on an arbor shall be considered as a shank mounted tool.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies all hazards arising from the use of tools for woodworking machines, and describes the methods for the elimination or reduction of these hazards by tool design and by the provision of information. This document deals with milling tools (bore mounted, shank mounted), integrated tools and circular saw blades.

  • Standard
    36 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document deals with all significant hazards, hazardous situations and events as listed in Clause 4 which are relevant to firewood and dual-purpose circular sawing machines for firewood/circular saw benches,with manual loading and/or unloading, hereinafter referred to as machines, designed to cut solid wood." On Combined circular sawing machines for firewood - Log splitting machines only the circular sawing machine for firewood is covered by this European Standard. For the requirements for the log splitting part of this machine see EN 609-1: 1999 and EN 609-2: 1999.

  • Standard
    60 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    61 pages
    German language
    sale 10% off
    e-Library read for
    1 day

ISO 19085-6:2017 gives the safety requirements and measures for stationary and displaceable hand-fed single spindle vertical moulding machines, hereinafter referred to as "machines", designed to cut wood and materials with similar physical characteristics to wood.
NOTE 1 For the definitions of stationary and displaceable machines, see ISO 19085‑1:2017, 3.4 and 3.5.
It deals with all significant hazards, hazardous situations and events as listed in Clause 4, relevant to the machines when they are operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also, transport, assembly, dismantling, disabling and scrapping phases are taken into account.
NOTE 2 For relevant but not significant hazards, e.g. sharp edges of the machine frame, see ISO 12100:2010.

  • Standard
    66 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 19085-3:2017 gives the safety requirements and measures for numerically controlled (NC) boring machines, NC routing machines and NC combined boring/routing machines (as defined in 3.1), hereinafter referred to as "machines".
ISO 19085-3:2017 deals with all significant hazards, hazardous situations and events, listed in Clause 4, relevant to the machines when they are operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also, transport, assembly, dismantling, disabling and scrapping phases have been taken into account.

  • Standard
    76 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 19085-8:2017 gives the safety requirements and measures for stationary calibrating and sanding machines, with an integrated feed and one or more sanding belt units positioned above and/or below the work piece level, with manual or automatic loading and/or unloading, hereinafter referred to as "machines". ISO 19085-8:2017 deals with all significant hazards, hazardous situations and events as listed in Clause 4, relevant to the machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer, including reasonably foreseeable misuse. Also, transport, assembly, dismantling, disabling and scrapping phases have been taken into account. NOTE 1 For relevant but not significant hazards, e.g. sharp edges of the machine frame, see ISO 12100:2010. ISO 19085-8:2017 is also applicable to machines fitted with one or more of the following devices/additional working units, whose hazards have been dealt with: - transversal sanding unit; - cleaning brushing unit; - satining roller unit; - disk brushing unit; - texturing brushing roller unit; - texturing brushing belt unit; - cutterblock unit; - texturing band saw unit; - spiked roller unit; - antistatic bars; - conveyor directly controlled by the machine; - additional work piece vacuum clamping device. The machines are designed to calibrate and/or sand work pieces, in shape of panels or beams, consisting of: a) solid wood; b) material with similar physical characteristics to wood (see ISO 19085-1:2017, 3.2); c) gypsum boards, gypsum bounded fibreboards; d) composite materials with core consisting of e.g. polyurethane or mineral material; e) composite boards made from the materials listed above; f) all materials listed above, also already lacquered. ISO 19085-8:2017 does not deal with hazards related to: - specific devices other than those listed above; - access through in-feed and out-feed openings of machines with a work piece height capacity greater than 550 mm; - systems for automatic loading and/or unloading of the work piece to/from a single machine; NOTE 2 Loading the machine manually includes manually placing the work piece onto a conveyor directly controlled by the machine. Unloading the machine manually includes manually removing the work piece from a conveyor directly controlled by the machine. - interfacing of the machine with any other machine. ISO 19085-8:2017 is not applicable to machines intended for use in potentially explosive atmosphere and to machines manufactured prior to the date of its publication.

  • Standard
    29 pages
    English language
    sale 15% off
  • Standard
    31 pages
    French language
    sale 15% off

This international standard deals with all significant hazards, hazardous situations and events as listed in
Clause 4 which are relevant to stationary and displaceable dimensions saws, hereinafter referred to as
machines‖, designed to cut wood and material with similar physical characteristics to wood, when they are
operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer
including reasonably foreseeable misuse. Also transport, assembly, dismantling, disabling and scrapping
phases are taken into account.
The machines may also be fitted with one or more of the following devices/facilities, whose hazards have
been dealt with:
a) facility for the main saw blade and scoring saw blade (if any) to be raised and lowered;
b) facility to tilt the main saw blade and scoring saw blade (if any) for angled cutting;
c) facility for scoring;
d) facility for grooving with milling tool with a width not exceeding 20 mm in one pass;
e) demountable power feed unit;
f) post-formed edge pre-cutting unit;
g) power operated sliding table;
h) workpiece clamping.

  • Standard
    62 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This international standard deals with all significant hazards, hazardous situations and events as listed in Clause 4 which are relevant to horizontal beam panel sawing machines with the saw carriage of the front cutting line mounted below the workpiece support, which are manually or mechanically loaded and/or unloaded, hereinafter referred to as "machines", when they are operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also transport, assembly, dismantling, disabling and scrapping phases have been taken into account.

  • Standard
    47 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    47 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 19085-6:2017 gives the safety requirements and measures for stationary and displaceable hand-fed single spindle vertical moulding machines, hereinafter referred to as "machines", designed to cut wood and materials with similar physical characteristics to wood. NOTE 1 For the definitions of stationary and displaceable machines, see ISO 19085‑1:2017, 3.4 and 3.5. It deals with all significant hazards, hazardous situations and events as listed in Clause 4, relevant to the machines when they are operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also, transport, assembly, dismantling, disabling and scrapping phases are taken into account. NOTE 2 For relevant but not significant hazards, e.g. sharp edges of the machine frame, see ISO 12100:2010.

  • Standard
    53 pages
    English language
    sale 15% off
  • Standard
    53 pages
    French language
    sale 15% off

This European Standard specifies all hazards arising from the use of tools for woodworking machines, and describes the methods for the elimination or reduction of these hazards by tool design and by the provision of information. This document deals with milling tools (bore mounted, shank mounted), integrated tools and circular saw blades.

  • Standard
    36 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies the determination of the maximum speed for given eccentricity at clamping devices for the shank strength of milling tools with cylindrical and taper shank. It also specifies the marking of the tool. Bore mounted tools which are mounted on an arbor shall be considered as a shank mounted tool.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard deals with all significant hazards, hazardous situations and events as listed in Clause 4 which are relevant to circular sawing machines for firewood with manual loading and/or unloading with hand operated carriage, hereinafter referred to as "machines", designed to cut solid wood when they are used as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse.
This European Standard is not applicable to:
a)   combined circular sawing machines for firewood with additional units, i.e. log splitting units or circular saw bench units;
NOTE 1   Circular saw benches are dealt with in EN 1870-19:2013.
NOTE 2   Log splitting machines are dealt with in EN 609-1:1999+A2:2009 and EN 609-2:1999+A1:2009.
NOTE 3   A draft is under consideration to cover "combined firewood processors".
b)   machines where the saw blade is capable of tilting;
c)   log sawing machines where the saw unit moves to cut the workpiece;
d)   hand-held motor-operated electric tools or any adaptation permitting their use in a different mode, i.e. bench mounting;
NOTE 4   Hand-held motor-operated electric tools and saw benches to form an integrated whole with a hand-held motor-operated electric tools are covered by EN 60745-1:2009 together with EN 60745-2-5:2010.
For RIC engines driven machines hazard of engine electrical starting systems above 24 V are not dealt with in this standard.
This document is not applicable to machines which are manufactured before the date of its publication as EN.
NOTE 5   Machines covered by this document are listed under 1.1 and/or 1.2 of Annex IV of the Machinery Directive.

  • Standard
    60 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    61 pages
    German language
    sale 10% off
    e-Library read for
    1 day

ISO 19085-3:2017 gives the safety requirements and measures for numerically controlled (NC) boring machines, NC routing machines and NC combined boring/routing machines (as defined in 3.1), hereinafter referred to as "machines". ISO 19085-3:2017 deals with all significant hazards, hazardous situations and events, listed in Clause 4, relevant to the machines when they are operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also, transport, assembly, dismantling, disabling and scrapping phases have been taken into account.

  • Standard
    64 pages
    English language
    sale 15% off
  • Standard
    64 pages
    French language
    sale 15% off

This international standard deals with all significant hazards, hazardous situations and events as listed in Clause 4 which are relevant to horizontal beam panel sawing machines with the saw carriage of the front cutting line mounted below the workpiece support, which are manually or mechanically loaded and/or unloaded, hereinafter referred to as "machines", when they are operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also transport, assembly, dismantling, disabling and scrapping phases have been taken into account.

  • Standard
    47 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    47 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 19085-5:2017 gives the safety requirements and measures for stationary and displaceable dimension saws, hereinafter referred to as "machines", designed to cut wood and material with similar physical characteristics to wood.
NOTE 1 For the definitions of stationary and displaceable machines, see ISO 19085‑1:2017, 3.4 and 3.5.
ISO 19085-5:2017 deals with all significant hazards, hazardous situations and events as listed in Clause 4, relevant to the machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also, transport, assembly, dismantling, disabling and scrapping phases have been taken into account.
NOTE 2 For relevant but not significant hazards, e.g. sharp edges of the machine frame, see ISO 12100.
ISO 19085-5:2017 is also applicable to machines fitted with one or more of the following devices/additional working units, whose hazards have been dealt with:
- device for the main saw blade and scoring saw blade to be raised and lowered;
- device to tilt the main saw blade and scoring saw blade for angled cutting;
- device for scoring;
- device for grooving with milling tool with a width not exceeding 20 mm;
- demountable power feed unit;
- post-formed edge pre-cutting unit;
- power-operated sliding table;
- workpiece clamping.
NOTE 3 Dimension saws are used for ripping, cross cutting, dimensioning and grooving.
ISO 19085-5:2017 is not applicable to machines intended for use in potentially explosive atmospheres or to machines manufactured prior to the date of its publication.

  • Standard
    62 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 19085-2:2017 gives the safety requirements and measures for horizontal beam panel circular sawing machines with the saw carriage of the front cutting line mounted below the work-piece support, which are manually and/or powered loaded and manually unloaded, hereinafter referred to as "machines". ISO 19085-2:2017 deals with all significant hazards, hazardous situations and events as listed in Clause 4, relevant to the machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also, transport, assembly, dismantling, disabling and scrapping phases have been taken into account. NOTE For relevant but not significant hazards, e.g. sharp edges of the machine frame, see ISO 12100:2010. ISO 19085-2:2017 is also applicable to machines fitted with one or more of the following devices/additional working units, whose hazards have been dealt with: - side pressure device; - device for powered unloading; - unit for scoring; - unit for post-formed/soft-formed edge pre-cutting; - panel turning device; - front side turn table; - pushing out device; - pneumatic clamping of the saw blade; - powered panel loading device; - device for grooving by milling tool; - one or more additional cutting lines inside the machine for longitudinal and/or head cut (before the transversal cutting line); - work-piece vacuum clamping as part of a front side turn table or of a panel loading device. The machines are designed for cutting panels consisting of a) solid wood, b) material with similar physical characteristics to wood (see ISO 19085‑1:2017, 3.2), c) gypsum boards, gypsum bounded fibreboards, d) composite boards made from the materials listed above, and e) composite materials with core consisting of e.g. polyurethane or mineral material laminated with light alloy. ISO 19085-2:2017 does not deal with hazards related to - specific features that differ from the dashed list above, - the machining of panels with milling tools for grooving, - powered unloading of panels, - rear half of split pressure beam on the front cutting line, - the combination of a single machine being used with any other machine (as part of a line). ISO 19085-2:2017 is not applicable to machines intended for use in potentially explosive atmospheres or to machines manufactured prior to the date of its publication.

  • Standard
    35 pages
    English language
    sale 15% off
  • Standard
    37 pages
    French language
    sale 15% off

ISO 19085-5:2017 gives the safety requirements and measures for stationary and displaceable dimension saws, hereinafter referred to as "machines", designed to cut wood and material with similar physical characteristics to wood. NOTE 1 For the definitions of stationary and displaceable machines, see ISO 19085‑1:2017, 3.4 and 3.5. ISO 19085-5:2017 deals with all significant hazards, hazardous situations and events as listed in Clause 4, relevant to the machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also, transport, assembly, dismantling, disabling and scrapping phases have been taken into account. NOTE 2 For relevant but not significant hazards, e.g. sharp edges of the machine frame, see ISO 12100. ISO 19085-5:2017 is also applicable to machines fitted with one or more of the following devices/additional working units, whose hazards have been dealt with: - device for the main saw blade and scoring saw blade to be raised and lowered; - device to tilt the main saw blade and scoring saw blade for angled cutting; - device for scoring; - device for grooving with milling tool with a width not exceeding 20 mm; - demountable power feed unit; - post-formed edge pre-cutting unit; - power-operated sliding table; - workpiece clamping. NOTE 3 Dimension saws are used for ripping, cross cutting, dimensioning and grooving. ISO 19085-5:2017 is not applicable to machines intended for use in potentially explosive atmospheres or to machines manufactured prior to the date of its publication.

  • Standard
    50 pages
    English language
    sale 15% off
  • Standard
    53 pages
    French language
    sale 15% off

ISO 19085-1:2017 gives the safety requirements and measures to reduce risks related to woodworking machines arising during operation, adjustment, maintenance, transport, assembly, dismantling, disabling and scrapping and which are common to machines used in the woodworking industry. It is applicable to woodworking, stationary and displaceable machines when they are used as intended and under the conditions foreseen by the manufacturer. NOTE 1 For relevant but not significant hazards, e.g. sharp edges of the machine frame, see ISO 12100:2010. ISO 19085-1:2017 is intended to be used in conjunction with the other parts of ISO 19085, applicable to specific machine types. ISO 19085-1:2017 is not applicable to machines intended for use in potential explosive atmospheres or to machines manufactured prior to the date of its publication. NOTE 2 Machines for capturing and extracting dust are covered by EN 12779 and EN 16770.

  • Standard
    47 pages
    English language
    sale 15% off
  • Standard
    49 pages
    French language
    sale 15% off

This European Standard applies to transportable motor-operated electric tools and deals with the measurement procedure for planers and thicknessers for measurements of dust emission.

  • Standard
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This clause of Part 1 is applicable, except as follows: Addition: This part of EN 50632 applies to transportable mitre saws intended to cut wood and wood-based materials.

  • Standard
    5 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This clause of Part 1 is applicable, except as follows: Addition: This part of EN 50632 applies to transportable table saws intended to cut wood or wood-based materials.

  • Standard
    5 pages
    English language
    sale 10% off
    e-Library read for
    1 day