This document specifies the requirements for solid-wall styrene copolymer blend (SAN + PVC) pipes and fittings for soil and waste discharge (low and high temperature) above ground inside buildings, and for the system itself. It does not include buried pipework. It also specifies the test parameters for the test methods referred to within this document. This document is applicable to SAN + PVC pipes and fittings, as well as assemblies of such pipes and fittings, intended to be used for the following purposes: a) soil and waste discharge pipework for the conveyance of domestic waste waters (low and high temperature); b) ventilation pipework associated with a); c) rainwater pipework inside the building. This document is applicable to pipes and fittings designed for jointing by means of elastomeric sealing rings, solvent cementing or integral dual-purpose sockets, i.e. for elastomeric ring seal joints and/or for solvent cement joints.

  • Standard
    30 pages
    English language
    sale 15% off
  • Draft
    30 pages
    English language
    sale 15% off

This document specifies field survey methods for measuring a) airborne sound insulation between rooms, b) impact sound insulation of floors, c) airborne sound insulation of façades, and d) sound pressure levels in rooms caused by service equipment. The methods described in this document are applicable for measurements in rooms of dwellings or in rooms of comparable size with a maximum of 150 m3. For airborne sound insulation, impact sound insulation and façade sound insulation the method gives values which are (octave band) frequency dependent. They can be converted into a single number characterising the acoustical performances by application of ISO 717-1 and ISO 717-2. For heavy/soft impact sound insulation, the results also are given as A-weighted maximum impact sound pressure level. For service equipment sound the results are given directly in A - or C -weighted sound pressure levels.

  • Standard
    33 pages
    English language
    sale 15% off
  • Standard
    34 pages
    French language
    sale 15% off
  • Draft
    33 pages
    English language
    sale 15% off
  • Draft
    34 pages
    French language
    sale 15% off

The document specifies, dimensions, materials and performance requirements (including methods of test) for expansion groups, of nominal sizes from DN 15 to DN 25, having working pressures ) from 0,1 MPa (1 bar) to 1,0 MPa (10 bar).
Expansion groups shall be fitted to the cold potable water supply only for expansion purposes, e.g. of storage water heaters, having a maximum distribution temperature of 95 °C.
Expansion groups limit pressure in the water heater to which they are fitted, that is produced by thermal expansion of the water, prevent the backflow of water into the supply pipe and prevent the discharged water to get into contact with the water in the water heater.
Expansion groups do not control temperature and alone do not constitute the protection required for storage water heaters.
NOTE   The use of the device specified in this Standard does not override the need to use controls (e.g. thermostats and thermal cut-outs) which act directly on the power sources of water heaters.

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the test gases, test pressures and categories of appliances relative to the use of gaseous fuels of the first, second and third families. It serves as a reference document in the specific standards for appliances that fall within the scope of the Council Directive on the approximation of the laws of Member States concerning gas appliances 2009/142/EC.
The standard makes recommendations for the use of the gases and pressures to be applied for the tests. The full procedure will be given in the corresponding appliance standards.
NOTE   The test gases and the test pressures specified in this standard are in principle intended to be used with all the appliances in order to establish conformity with the corresponding standards.
However, the use of some test gases and test pressures may not be appropriate in the following cases:
-   appliances with nominal heat input greater than 300 kW;
-   appliances constructed on site;
-   appliances in which the final design is influenced by the user;
-   appliances constructed for use with high supply pressures (notably direct use of the saturated vapour pressure).
In these cases, the specific appliance standards may specify other test conditions in order to establish compliance with their requirements.

  • Standard
    57 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    57 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the properties of piping system components made from glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP). It is suited for all types of water supply, drainage and sewerage with or without pressure. Types of water supply include, but are not limited to, raw water, irrigation, cooling water, potable water, salt water, sea water, penstocks in power plants, processing plants and other water-based applications. This document is applicable to GRP UP piping systems, with flexible or rigid joints with or without end thrust load-bearing capability, primarily intended for use in direct buried installations. NOTEÂ 1Â Â For the purpose of this document, the term polyester resin (UP) also includes vinyl-ester resins (VE). NOTEÂ 2Â Â Piping systems conforming to this document can also be used for non-buried applications, provided the influence of the environment and the supports are considered in the design of the pipes, fittings and joints. NOTEÂ 3Â Â This document can also apply for other installations, such as slip-lining rehabilitation of existing pipes. NOTEÂ 4Â Â ISOÂ 10467 and ISOÂ 10639, which are replaced by this document, are also referenced in ISOÂ 25780, which specifies requirements for GRP-pipes used for jacking installation. The requirements for the hydrostatic pressure design of pipes referring to this document meet the requirements of ISO/TSÂ 20656-1 and the general principle for the reliability of structures detailed in ISOÂ 2394 and in ENÂ 1990. These International Standards provide procedures for the harmonization of design practices and address the probability of failure, as well as possible consequences of failures. The design practices are based on a partial safety factor concept, as well as on risk management engineering. This document is applicable to circular pipes, fittings and their joints of nominal sizes from DNÂ 50 to DNÂ 4000, which are intended to be used for the conveyance of water, sewage and drainage at normal service conditions, with or without pressure.

  • Standard
    60 pages
    English language
    sale 15% off
  • Standard
    62 pages
    French language
    sale 15% off
  • Draft
    60 pages
    English language
    sale 15% off
  • Draft
    60 pages
    English language
    sale 15% off
  • Draft
    62 pages
    French language
    sale 15% off
  • Draft
    61 pages
    French language
    sale 15% off

This European Standard applies to heating and cooling systems embedded into the enclosure surfaces of the room to be heated or to be cooled.
This document deals with the use in practical engineering of the results coming from part 2 and 5 and is applicable to floor-, ceiling- and wall heating systems, as well floor-, ceiling- and wall cooling systems.
For heating systems, physiological limitations are taken into account when specifying the surface temperatures. In the case of floor heating systems the limitations are realised by a design based on the characteristic curves and limit curves determined in accordance with part 2 of this Standard.
For cooling systems, only a limitation with respect to the dew point is taken into account. In predominating practice, this means that physiological limitations are included as well.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard applies to heating and cooling systems embedded into the enclosure surfaces of the room to be heated or to be cooled.
This document specifies uniform requirements for the design and the construction of heating and cooling floor, ceiling and wall structures to ensure that the heating/cooling systems are suited to the particular application.
The requirements specified by this Standard apply only to the components of the heating/cooling systems which are part of the heating/cooling system. This document excludes all other elements which are not part of the heating/cooling system.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard applies to water based heating and cooling systems embedded into the enclosure surfaces of the room to be heated or to be cooled. Part 5 of this standard deals with the recalculation of values determined in Part 2 of this European Standard for the system in question, using it for floor heating applications. The recalculation method described in this part of the standard enables the conversion of the calculation and test results of Part 2 into results for other surface orientations in the room, i. e. for ceiling and wall heating, as well as for the application as cooling surfaces, i. e. for floor, ceiling and wall cooling. It has to be emphasised that the test results of Part 2 of this European Standard are the basis of all calculation. Therefore the use of this prove method is necessary whether or not the system in question is used for heating or cooling application.
This European Standard shall be applied to commercial trade and practical engineering if proved and certifiable values of the thermal output shall be used.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day

1.1 General
This European Standard applies to heating boilers including safety devices up to a nominal heat output of 500 kW which are designed for the burning of solid fuels only and are operated according to the instructions of the boiler manufacturer.
This European Standard deals with significant hazards, hazardous situations and events relevant to heating boilers used as intended and under the conditions foreseen by the manufacturer (see Clause 4).
The boilers may operate under natural draught or forced draught. The stoking may work manually or automatically.
The boilers may operate under room sealed conditions in case of supervised under pressure in the combustion chamber.
The boilers may operate in condensing condition.
NOTE This European Standard deals with boilers which are both within and outside of the scope of the Machinery
Directive 2006/42/EC.
This European Standard contains requirements and test methods for safety, combustion quality, operating characteristics, marking and maintenance of heating boilers and secondary emission reduction appliances and efficiency improvement appliances. It also covers all external equipment that influences the safety systems (e.g. back burning safety device, integral fuel hopper).
This European Standard covers only boilers that include burners as a unit. The standard applies to the combination of a boiler body with a solid fuel burner according to EN 15270 as a unit only when the whole unit is tested in accordance with this European Standard.
Heating boilers in accordance with this European Standard are designed for central heating installations where the heat carrier is water and the maximum allowable temperature is 110 °C, and which can operate at a maximum allowable operating pressure of 6 bars. For heating boilers with a built-in or attached water heater (storage or continuous flow heater), this European Standard only applies to those parts of the water heater which are necessarily subject to the operating conditions of the heating boiler (heating part).
This European Standard does not apply to:
heating boilers and other heating appliances which are also designed for the direct heating of the place of installation;
cooking appliances;
the design and construction of external fuel storage and transportation devices prior to the safety devices of the boiler;
room sealed applications above a nominal heat output > 70 kW or operated with positive pressure in the combustion chamber or operated under natural draught;
This European Standard specifies the necessary terminology for solid fuel heating boilers, the control and safety related requirements, the design requirements, the technical heating requirements (taking into account the environmental requirements) and testing, as well as the marking requirements.
This European Standard is not applicable to heating boilers which are tested before the date of its publication as an EN (European Standard).
1.2 Fuels
These boilers may burn either fossil fuels, biogenic fuels or other fuels such as peat, as specified for their use by the boiler manufacturer, in accordance with the requirements of this European Standard.
Solid fuels included in this European Standard are categorised as follows.
1.2.1 Biogenic fuels
Biomass in a natural state, in the form of:
Adaptation to new fuels standards and consideration of new fuels standards in preparation.
A log wood with moisture content w ≤ 25 %, according to EN 14961-5;
B1 chipped wood (wood chipped by machine, usually up to a maximum length of 15 cm) with moisture content from w 15 % to w 35 %, according to EN 14961-4;
B2 chipped wood as under B1, except with moisture content w > 35 %;
C1 compressed wood (e.g. pellets without additives, made of wood and/or bark particles; natural binding agents such as molasses, vegetable paraffins and starch are permitted), pellets according to EN 14961-2;
(...)

  • Standard
    98 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    95 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard is applicable to water based surface embedded heating and cooling systems in residential, office and other buildings, the use of which corresponds to or is similar to that of residential buildings.
This European Standard applies to heating and cooling systems embedded into the enclosure surfaces of the room to be heated or to be cooled.
It also applies as appropriate to the use of other heating media instead of water.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies the boundary conditions and the prove methods for the determination of the thermal output of hot water floor heating systems as a function of the temperature difference between the heating medium and the room temperature.
This standard shall be applied to commercial trade and practical engineering if proved and certifiable values of the thermal output shall be used.
This European Standard applies to heating and cooling systems embedded into the enclosure surfaces of the room to be heated or to be cooled. This Part of this European Standard applies to hot water floor heating systems. Applying of Part 5 of this European Standard requires the prior use of this Part of this European Standard. Part 5 of this European Standard deals with the conversion of the thermal output of floor heating systems determined in Part 2 into the thermal output of heating surfaces embedded in walls and ceilings as well as into the thermal output of cooling surfaces embedded in floors, walls and ceilings.
The thermal output is proved by a calculation method (Clause 6) and by a test method (Clause 9). The calculation method is applicable to systems corresponding to the definitions in EN 1264 1 (type A, type B, type C, type D). For systems not corresponding to these definitions, the test method shall be used. The calculation method and the test method are consistent with each other and provide correlating and adequate prove results.
The prove results, expressed depending on further parameters, are the standard specific thermal output and the associated standard temperature difference between the heating medium and the room temperature as well as fields of characteristic curves showing the relationship between the specific thermal output and the temperature difference between the heating medium and the room.

  • Standard
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    42 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies requirements for the design, construction and operation of kitchen ventilation ceilings, including technical safety, ergonomic and hygienic features.
This European Standard is applicable to ventilation systems in commercial kitchens, associated areas and other installations processing foodstuffs intended for commercial use. Kitchens and associated areas are special rooms in which meals are prepared, where tableware and equipment is washed, cleaned and food is stored.
This European Standard is applicable to kitchen ventilation ceilings except those used in domestic kitchens.
A method of verification of each requirement is also specified.
Unless otherwise specified, the requirements of this standard need to be checked by way of inspection and/or measurement.
NOTE   Please note the possible existence of additional or alternative local national regulations on installation, appliance requirements and inspection, maintenance and operation.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies requirements and gives recommendations for the design, installation, testing, maintenance and safety of kitchen fire suppression systems in buildings.
This European Standard is applicable to ventilation systems in commercial kitchens, associated areas and other installations processing foodstuffs intended for commercial use. Kitchens and associated areas are special rooms in which meals are prepared, where tableware and equipment is washed, cleaned, food is stored and food waste areas.
This European Standard is applicable to fire suppression systems except those used in domestic kitchens or industrial food processing facilities.
Unless otherwise specified, the requirements of this standard should be checked by way of inspection and/or measurement.
NOTE   Please note the possible existence of additional or alternative local national regulations on installation, appliance requirements and inspection, maintenance and operation.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the necessary dimensions to permit the installation of passenger lifts of class I, II, III and VI.
These dimensions reflect the requirements for the apparatus.
This document is applicable to all new lift installations, irrespective of drive systems, including a car with one entrance, to be installed in a new building. However, for arrangements with counterweight at the side, a through-entrance configuration is possible. Where relevant, this document is also applicable to an installation in an existing building.
This document is not applicable to lifts of rated speed greater than 6,0 m/s.
NOTE It is the responsibility of the user to consult the manufacturer for such installations.

  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    30 pages
    English language
    sale 15% off
  • Standard
    30 pages
    English language
    sale 15% off
  • Standard
    30 pages
    French language
    sale 15% off
  • Standard
    31 pages
    French language
    sale 15% off

This document specifies the minimum requirements for the safe and independent access and use of lifts by persons, including persons with disabilities. It covers the needs of persons with disabilities according to Annex A.
NOTE   For guidance on solutions for increased accessibility and usability, see Annex D.

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies aerodynamic, acoustic and electrical power performance test methods for unidirectional ventilation units used in residential ventilation systems.
This document is applicable to ventilation units:
-   installed on a wall or in a window without any duct, A category;
-   installed in the upstream of a duct, B category;
-   installed in the downstream of a duct, C category;
-   installed in a duct, or with duct connection upstream and downstream, D category;
-   with one or several inlets/outlets;
-   installed in a system with a heat pump for domestic hot water or water for cooling or heating;
-   which can be used for supply or exhaust.
This document does not apply to:
-   fan assisted cowls which are tested according to EN 13141 5;
-   mechanical supply and exhaust units which are tested according to prEN 13141 7 or prEN 13141 8.

  • Standard
    44 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the laboratory test methods and test requirements for the testing of aerodynamic, thermal, acoustic and electrical performance characteristics of ducted mechanical supply and exhaust ventilation units intended for single family houses.
This document is applicable to unit that contain at least, within one or more casing:
-   fans for mechanical supply and exhaust;
-   air filters;
-   air-to-air heat exchanger and/or air-to-air heat pump for air heat recovery;
-   control system.
Such unit can be provided in more than one assembly, the separate assemblies of which are designed to be used together.
The different possible arrangements of heat recovery, heat exchangers and/or heat pumps are described in Annex A.
This document does not deal with non-ducted units.
This document does not cover ventilation systems that may also provide water space heating and hot water.
This document does not cover units including combustion engine, driven compression heat pumps and absorption heat pumps.
Electrical safety requirements are given in EN 60335 2 40 and EN 60335 2 80.

  • Standard
    54 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    46 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 62052-11:2020 (E) specifies requirements and associated tests, with their appropriate conditions for type testing of AC and DC electricity meters. This document details functional, mechanical, electrical and marking requirements, test methods, and test conditions, including immunity to external influences covering electromagnetic and climatic environments.
This document applies to electricity metering equipment designed to:
• measure and control electrical energy on electrical networks (mains) with voltage up to 1 000 V AC, or 1 500 V DC;
• have all functional elements, including add-on modules, enclosed in, or forming a single meter case with exception of indicating displays;
• operate with integrated displays (electromechanical or static meters);
• operate with detached indicating displays, or without an indicating display (static meters only);
• be installed in a specified matching sockets or racks;
• optionally, provide additional functions other than those for measurement of electrical energy.
Meters designed for operation with Low Power Instrument Transformers (LPITs as defined in the IEC 61869 series) may be tested for compliance with this document and the relevant IEC 62053 series documents only if such meters and their LPITs are tested together as directly connected meters.
This document is also applicable to auxiliary input and output circuits, operation indicators, and test outputs of equipment for electrical energy measurement.
This document also covers the common aspects of accuracy testing such as reference conditions, repeatability and measurement of uncertainty.
This document does not apply to:
• meters for which the voltage line-to-neutral derived from nominal voltages exceeds 1 000 V AC, or 1 500 V DC;
• meters intended for connection with low power instrument transformers (LPITs as defined in the IEC 61869 series of standards) when tested without such transformers;
• metering systems comprising multiple devices (except of LPITs) physically remote from one another;
• portable meters;
• meters used in rolling stock, vehicles, ships and airplanes;
• laboratory and meter test equipment;
• reference standard meters;
• data interfaces to the register of the meter;
• matching sockets or racks used for installation of electricity metering equipment;
• any additional functions provided in electrical energy meters.
This document does not cover measures for the detection and prevention of fraudulent attempts to compromise a meter’s performance (tampering).
This second edition cancels and replaces the first edition published in 2003, and its amendment 1:2016. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) Removed all meter safety requirements; the meter safety requirements are covered in IEC 62052-31:2015;
b) Included requirements for meter power consumption and voltage requirements from IEC 62053-61; IEC 62053-61 is withdrawn;
c) Included requirements for meter symbols from IEC 62053-52; IEC 62053-52 is withdrawn;
d) Included requirements for meter pulse output devices from IEC 62053-31; IEC 62053-31 is withdrawn;
e) Added new requirements and tests including: meters with detached indicating displays, and meters without indicating displays, meter sealing provisions; measurement uncertainty and repeatability; time-keeping accuracy; type tes

  • Standard
    125 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 62053-23:2020 applies only to static var-hour meters of accuracy classes 2 and 3 for the measurement of alternating current electrical reactive energy in 50 Hz or 60 Hz networks and it applies to their type tests only.
For practical reasons, this document is based on a conventional definition of reactive energy for sinusoidal currents and voltages containing the fundamental frequency only.
This document applies to electricity metering equipment designed to:
• measure and control electrical energy on electrical networks (mains) with voltage up to 1 000 V AC;
• have all functional elements, including add-on modules, enclosed in, or forming a single meter case with exception of indicating displays;
• operate with integrated or detached indicating displays, or without an indicating display;
• be installed in a specified matching socket or rack;
• optionally, provide additional functions other than those for measurement of electrical energy.
Meters designed for operation with low power instrument transformers (LPITs as defined in the IEC 61869 series) may be considered as compliant with this document only if such meters and their LPITs are tested together and meet the requirements for directly connected meters.
This document does not apply to:
• meters for which the voltage line-to-neutral derived from nominal voltages exceeds 1 000 V AC;
• meters intended for connection with low power instrument transformers (LPITs as defined in the IEC 61869 series) when tested without such transformers;
• metering systems comprising multiple devices (except LPITs) physically remote from one another;
• portable meters;
• meters used in rolling stock, vehicles, ships and airplanes;
• laboratory and meter test equipment;
• reference standard meters;
• data interfaces to the register of the meter;
• matching sockets or racks used for installation of electricity metering equipment;
• any additional functions provided in electrical energy meters.
This document does not cover measures for the detection and prevention of fraudulent attempts to compromise a meter’s performance (tampering).
This second edition cancels and replaces the first edition published in 2003 and its amendment 1:2016. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) Removed all meter safety requirements; the meter safety requirements are covered in IEC 62052-31:2015.
b) Replaced Ib with In; Ib is no longer used when referencing directly connected meters.
c) Moved the descriptions of all general requirements and test methods from IEC 62053-21: 2003, IEC 62053-22: 2003, IEC 62053-23: 2003, IEC 62053-24: 2003 to IEC 62052-11:2020; IEC 62053-21:2020, IEC 62053-22:2020, IEC 62053-23:2020, IEC 62053-24:2020 contain only accuracy class specific requirements.
d) Added new requirements and tests concerning:
1) measurement uncertainty and repeatability (7.3, 7.8);
2) influence of fast load current variations (9.4.12);
3) immunity to conducted differential current disturbances in the 2 kHz to 150 kHz frequency range (9.3.8).
e) Meters designed for operation with low power instrument transformers (LPITs) may be tested for compliance with this document as directly connected meters.
The reactive energy accuracy classes 2 and 3 defined in IEC 62053-23 have also been added to IEC 62053-24. The TC13

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 62053-21:2020 applies only to static watt-hour meters of accuracy classes 0,5, 1 and 2 for the measurement of alternating current electrical active energy in 50 Hz or 60 Hz networks and it applies to their type tests only.
This document applies to electricity metering equipment designed to:
• measure and control electrical energy on electrical networks (mains) with voltage up to 1 000 V AC;
• have all functional elements, including add-on modules, enclosed in, or forming a single meter case with exception of indicating displays;
• operate with integrated or detached indicating displays, or without an indicating display;
• be installed in a specified matching socket or rack;
• optionally, provide additional functions other than those for measurement of electrical energy.
Meters designed for operation with low power instrument transformers (LPITs as defined in the IEC 61869 series) may be tested for compliance with this document only if such meters and their LPITs are tested together and meet the requirements for directly connected meters.
This document does not apply to:
• meters for which the voltage line-to-neutral derived from nominal voltages exceeds 1 000 V AC;
• meters intended for connection with low power instrument transformers (LPITs as defined in the IEC 61869 series) when tested without such transformers;
• metering systems comprising multiple devices (except LPITs) physically remote from one another;
• portable meters;
• meters used in rolling stock, vehicles, ships and airplanes;
• laboratory and meter test equipment;
• reference standard meters;
• data interfaces to the register of the meter;
• matching sockets or racks used for installation of electricity metering equipment;
• any additional functions provided in electrical energy meters.
This document does not cover measures for the detection and prevention of fraudulent attempts to compromise a meter’s performance (tampering).
This second edition cancels and replaces the first edition published in 2003 and its amendment 1:2016. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) Removed all meter safety requirements; the meter safety requirements are covered in IEC 62052-31: 2015.
b) Replaced Ib with In; Ib is no longer used when referencing directly connected meters.
c) Moved the descriptions of all general requirements and test methods from IEC 62053-21: 2003, IEC 62053-22: 2003, IEC 62053-23: 2003, IEC 62053-24: 2003 to IEC 62052-11:2020; IEC 62053-21:2020, IEC 62053-22:2020, IEC 62053-23:2020, IEC 62053-24:2020 contain only accuracy class specific requirements.
d) Added new requirements and tests concerning:
1) measurement uncertainty and repeatability (7.3, 7.8);
2) influence of fast load current variations (9.4.12);
3) immunity to conducted differential current disturbances in the 2 kHz to 150 kHz frequency range (9.3.8).
e) Meters designed for operation with low power instrument transformers (LPITs) may be tested for compliance with this document as directly connected meters.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 62053-24:2020 applies only to static var-hour meters of accuracy classes 0,5S, 1S, 1, 2 and 3 for the measurement of alternating current electrical reactive energy in 50 Hz or 60 Hz networks and it applies to their type tests only.
This document uses a conventional definition of reactive energy where the reactive power and energy is calculated from the fundamental frequency components of the currents and voltages only.
This document applies to electricity metering equipment designed to:
• measure and control electrical energy on electrical networks (mains) with voltage up to 1 000 V AC;
• have all functional elements, including add-on modules, enclosed in, or forming a single meter case with exception of indicating displays;
• operate with integrated or detached indicating displays, or without an indicating display;
• be installed in a specified matching socket or rack;
• optionally, provide additional functions other than those for measurement of electrical energy.
Meters designed for operation with low power instrument transformers (LPITs as defined in the IEC 61869 series) may be considered as compliant with this document only if such meters and their LPITs are tested together and meet the requirements for directly connected meters.
This document does not apply to:
• meters for which the voltage line-to-neutral derived from nominal voltages exceeds 1 000 V AC;
• meters intended for connection with low power instrument transformers (LPITs as defined in the IEC 61869 series) when tested without such transformers;
• metering systems comprising multiple devices (except LPITs) physically remote from one another;
• portable meters;
• meters used in rolling stock, vehicles, ships and airplanes;
• laboratory and meter test equipment;
• reference standard meters;
• data interfaces to the register of the meter;
• matching sockets or racks used for installation of electricity metering equipment;
• any additional functions provided in electrical energy meters.
This document does not cover measures for the detection and prevention of fraudulent attempts to compromise a meter’s performance (tampering).
This second edition cancels and replaces the first edition published in 2014 and its amendment 1:2016. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition: see Annex E

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European standard specifies and classifies the component/product performance characteristics which may be necessary for the design, rating and dimensioning, placing on the market of residential ventilation products and systems to provide the predetermined performance, comfort conditions of temperature, air velocity, humidity, hygiene and sound in the occupied zone.
It defines those performance characteristics (mandatory or optional) which shall be determined, measured and presented according to relevant test methods. It provides a classification scheme which leads to a full definition of product properties based on test methods described in various EN Standards and gives an overview of the test standards. Distinction between mandatory and optional requirement is left to each European and national regulations.
The codification part in Annex A and the classification part in Clause 4 apply to the following products:
-   unidirectional mechanical supply and exhaust residential ventilation units according to prEN 13141 4, prEN 13141 6 and prEN 13141 11;
-   ducted mechanical bidirectional residential ventilation units according to prEN 13141 7;
-   non-ducted mechanical bidirectional residential ventilation units according to prEN 13141 8.
This European standard does not apply to other products such as filters, fire dampers, ducts, control devices and sound attenuators, which may also be incorporated in residential ventilation.
This European standard specifies in Annex ZA the requirements of EU 1253/2014 and EU 1254/2014 for residential ventilation units below 1 000 m3/h air volume flow.
This European standard does not cover requirements raised by European Directives (e.g. low voltage directive, EMC directive) and other requirements such as corrosion, fire resistance and snow penetration.

  • Standard
    97 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    98 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 62053-22:2020 applies only to transformer operated static watt-hour meters of accuracy classes 0,1 S, 0,2 S and 0,5 S for the measurement of alternating current electrical active energy in 50 Hz or 60 Hz networks and it applies to their type tests only.
This document applies to electricity metering equipment designed to:
• measure and control electrical energy on electrical networks (mains) with voltage up to 1 000 V AC;
• have all functional elements, including add-on modules, enclosed in, or forming a single meter case with exception of indicating displays;
• operate with integrated or detached indicating displays, or without an indicating display;
• be installed in a specified matching socket or rack;
• optionally, provide additional functions other than those for measurement of electrical energy.
This document does not apply to:
• meters for which the voltage line-to-neutral derived from nominal voltages exceeds 1 000 V AC;
• meters intended for connection with low power instrument transformers (LPITs as defined in the IEC 61869 series) when tested without such transformers;
• metering systems comprising multiple devices physically remote from one another.
• portable meters;
• meters used in rolling stock, vehicles, ships and airplanes;
• laboratory and meter test equipment;
• reference standard meters;
• data interfaces to the register of the meter;
• matching sockets or racks used for installation of electricity metering equipment;
• any additional functions provided in electrical energy meters.
This document does not cover measures for the detection and prevention of fraudulent attempts to compromise a meter’s performance (tampering)
This second edition cancels and replaces the first edition published in 2003 and its amendment 1: 2016. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) Removed all meter safety requirements; the meter safety requirements are covered in IEC 62052-31: 2015.
b) Moved the descriptions of all general requirements and test methods from IEC 62053-21: 2003, IEC 62053-22: 2003, IEC 62053-23: 2003, IEC 62053-24: 2003 to IEC 62052-11:2020; IEC 62053-21:2020, IEC 62053-22:2020, IEC 62053-23:2020, IEC 62053-24:2020 contain only accuracy class specific requirements.
c) Added new requirements and tests concerning:
1) active energy meters of accuracy class 0,1S;
2) measurement uncertainty and repeatability (7.3, 7.8);
3) influence of fast load current variations (9.4.12);
4) immunity to conducted differential current disturbances in the 2 kHz to 150 kHz frequency range (9.3.8)

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document addresses the construction of buildings and other structures which provide accommodation for data centres based upon the criteria and classification for “physical security” within EN 50600 1 in support of availability.
This document specifies requirements and recommendations for the following:
a)   location and site selection (taking in to account natural environment and adjacencies);
b)   protection from environmental risks;
c)   site configuration;
d)   building construction;
e)   building configuration;
f)   provision of access;
g)   intrusion protection;
h)   physical fire protection;
i)   protection against damage from water;
j)   quality construction measures.
Safety and electromagnetic compatibility (EMC) requirements are outside the scope of this document and are covered by other standards and regulations. However, information given in this document can be of assistance in meeting these standards and regulations.
Conformance of data centres to the present document is covered in Clause 4.

  • Standard
    38 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 60364-7-710:2021 applies to electrical installations in medical locations so as to provide safety of patients and medical staff. These requirements refer to:
– hospitals and clinics or equivalent institutions (including equivalent transportable and mobile locations);
which, subject to assessment (710.30), can also include:
– sanatoriums and health clinics;
– dedicated locations in homes for senior citizens and aged care homes, where patients receive medical care;
– medical centres, outpatients' clinics and departments, casualty wards;
– other outpatients' institutions (industrial, sports and others);
– medical and dental practices;
– dedicated medical rooms in the workplace;
– other locations where medical electrical equipment is used;
– veterinary clinics;
– rooms in existing installations where a change of utilization for medical applications occur.
This list is not exhaustive.
The requirements of this document do not apply to ME equipment or ME systems.
This edition includes the following significant technical changes with respect to the previous edition:
a) the scope provides improved information to the application of this document;
b) some terms and definitions have been revised;
c) the validity of the respective parts of the IEC 60364 series has been verified and clauses updated;
d) Clause 710.30 has been extended;
e) Clause 710.41 has been updated;
f) Clause 710.413 has been renumbered as Clause 710.411;
g) in 710.411 insulation fault location systems have been added;
h) Clause 710.421 has been extended to include arc fault detection devices;
i) Clause 710.44 has been added;
j) Clause 710.51 has been updated and now covers distribution boards and electrical operating areas;
k) Clause 710.514, has been extended and includes separate subclauses on diagrams, documentation and operating instructions;
l) Subclauses 710.531 to 710.537 have been added;
m) Clause 710.55 has been updated;
n) Clause 710.56 has been added;
o) Clause 710.6, Verification, has been revised;
p) Annex A was deleted, and the contents integrated into 710.560.4;
q) former Annex B is now Annex A and has been updated;
r) an informative Annex B on guidance concerning electromagnetic interferences (EMI) in installations of buildings has been added

  • Standard
    83 pages
    English and French language
    sale 15% off

IEC 60335-2-67:2021 is available as IEC 60335-2-67:2021 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 60335-2-67:2021 deals with the safety of powered floor treatment machines intended for commercial indoor or outdoor use for the following applications:
- scrubbing,
- wet or dry pick-up,
- polishing and dry buffing,
- application of wax, sealing products and powder based detergents,
- shampooing,
- stripping, grinding and scarifying
of floors with an artificial surface.
These machines have a cleaning motion which is more lateral or periodic than linear.
By contrast, the cleaning motion of machines covered by IEC 60335-2-72 is more linear than lateral or periodic.
This standard applies to machines for commercial use. The following list, although not comprehensive, gives an indication of locations that are included in the scope:
- public use areas such as hotels, schools, hospitals;
- industrial locations, for example factories and manufacturing shops;
- retail outlets, for example shops and supermarkets;
- business premises, for example offices and banks;
- all uses other than normal housekeeping purposes.
These machines are not equipped with a traction drive.
Machines for the same intended function but equipped with a traction drive are covered by IEC 60335 2-72.
The following power systems are covered:
- internal combustion engines,
- mains powered motors up to a rated voltage of 250 V for single-phase appliances and 480 V for other appliances,
- battery-operated machines.
Battery-operated machines may be equipped with a built-in battery charger.
This standard does not apply to
- vacuum cleaners and water-suction cleaning appliances for household use (IEC 60335 2 2);
- floor treatment appliances for household use (IEC 60335-2-10);
- spray extraction machines for commercial use (IEC 60335-2-68);
- wet and dry vacuum cleaners, including power brush, for commercial use (IEC 60335 2 69);
IEC 60335-2-68 and IEC 60335-2-69 cover only machines without traction drive.
- floor treatment machines with or without traction drive, for commercial use (IEC 60335 2 72);
- hand-held and transportable motor-operated electric tools (IEC 60745 series, IEC 61029 series, IEC 62841 series);
- machines designed for use in corrosive or explosive environments (dust, vapour or gas);
- machines designed for picking up hazardous dusts (as defined in IEC 60335-2-69), inflammable substances, or glowing particles;
- machines designed for use in vehicles or on board of ships or aircraft.
This fifth edition cancels and replaces the fourth edition published in 2012 and its Amendment 1: 2016. It constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
- editorial and technical alignment with IEC 60335-1:2020.
This part 2 is to be used in conjunction with the latest edition of IEC 60335-1 and its amendments. It was established on the basis of the sixth edition (2020) of that standard.

  • Standard
    90 pages
    English and French language
    sale 15% off

This document presents guidelines for the implementation of Essential Requirements of Gas Appliances Regulation (EU) 2016/426 into hEN candidates for citation in the OJEU.
This document gives guidance that is additional to the CEN/CENELEC Internal Regulations, Part 3:2019, when this is necessary owing to the special requirements of gas appliances and fittings.
This document is intended for the drafting of gas appliances and fittings standards.

  • Guide
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This Technical Specification describes specific functional recommendations for the safe
design, handling, installation and operation of unplasticized polyamide (PA-U) gas piping
systems with fusion jointing and mechanical jointing with
a)  a maximum operating pressure (MOP) up to and including 16 bar;
b)  an operating temperature between -20 °C and +40 °C.
This Technical Specification covers PA pipes single layer solid wall.
This Technical Specification should be applied complementary to the functional requirements
in EN 12007-2.

  • Technical specification
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Technical specification
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This TS provides technical specifications and guidance for the installation of refrigeration, air conditioning and heat pump equipment This document provides technical information for the installation of refrigeration, air conditioning and heat pump equipment containing flammable refrigerants, in particular from class A3, complementing existing standards. The term “refrigerating system” used in this document includes air conditioners and heat pumps.
Refrigerants from toxicity class B are excluded from this scope.
This document includes risk mitigation measures not yet addressed in existing standards for specific refrigerant classes, or not fully reflecting the state of the art, and establishes complementary technical specifications related to the installation of equipment.
The following aspects are considered:
-   explosive atmosphere workplace and equipment;
NOTE   Further information can be found in Directive 99/92/EC (ATEX Workplace Directive) and Directive 2014/34/EU (ATEX Equipment Directive).
-   design and structural specifications for the installation site;
-   marking and labelling of equipment parts and installation site;
-   good practice for installing equipment, including tools and personal protection;
-   risk mitigation methods and related refrigerant charge limits;
-   risk assessments;
-   competence of personnel;
-   safety testing of systems and equipment.

  • Technical specification
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Technical specification
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document provides technical specifications for the operation, servicing, maintenance, repair and decommissioning of refrigeration, air conditioning and heat pump equipment containing flammable refrigerants, in particular from class A3, complementing existing standards.
Refrigerants from toxicity class B are excluded from this scope.
This document includes risk mitigation measures not yet addressed in existing standards for specific refrigerant classes, or not fully reflecting the state of the art, and establishes complementary technical specifications for the operation, servicing, maintenance, repair and decommissioning, .
The following aspects are considered:
-   explosive atmosphere workplace and equipment;
NOTE   Further information can be found in Directive 99/92/EC (ATEX Workplace Directive) and Directive 2014/34/EU (ATEX Equipment Directive).
-   good practice for the operation, servicing, maintenance, repair and decommissioning, including tools and personal protection;
-   risk mitigation methods;
-   risk assessments;
-   competence of personnel;
-   health and safety of personnel;
-   location of the equipment.

  • Technical specification
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Technical specification
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document gives requirements and guidance for the assessment of conformity of formulations, products and assemblies in accordance with EN 1329 1 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of third-party certification procedures.
NOTE 1   The quality management system is expected to conform to or is no less stringent than the relevant requirements to EN ISO 9001 [1].
NOTE 2   If third party certification is involved, the certification body is expected to be compliant with either EN ISO/IEC 17065 [2] or EN ISO/IEC 17021-series [3], as applicable.
NOTE 3   In order to help the reader, a basic test matrix is given in Annex A.
In conjunction with EN 1329 1, this document is applicable to piping systems made of unplasticized poly(vinyl chloride) (PVC U) intended for soil and waste discharge systems (low and high temperature):
-   inside buildings (application area code "B");
-   both inside buildings and buried in ground within the building structure (application area code "BD").

  • Technical specification
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Technical specification
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    French language
    sale 15% off
  • Draft
    5 pages
    English language
    sale 15% off

This document specifies a method for sampling fabric filter medium from a filter system in operation, and a test method for evaluating the degradation of the sampled filter medium. It applies to both woven and nonwoven fabric filter media. This document specifies a method for removing used filter medium from a dry type filtering dust collector, a method for removing dust from the sampled filter medium as part of preparation for testing, and measurement parameters for the test specimen. The number of filter elements to be sampled, their positions in the blocks of filter elements in the dust collector, the position and the size of the test specimens to be cut out from the filter element, measurement parameters and their test methods are also specified. This document also specifies a storage and transportation method for the sampled filter medium that will protect the health of workers and people conducting the tests.

  • Standard
    22 pages
    English language
    sale 15% off
  • Draft
    22 pages
    English language
    sale 15% off
  • Amendment
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Amendment
    5 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Amendment
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Amendment
    5 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Amendment
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Amendment
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Amendment
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Amendment
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Amendment
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Amendment
    5 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Amendment
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Amendment
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Amendment
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Amendment
    5 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Amendment
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Amendment
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the immunity performance criteria and test levels for apparatus used in lifts, escalators and moving walks which are intended to be permanently installed in buildings including the basic safety requirements in regard to their electromagnetic environment. These levels represent essential EMC requirements. This document refers to EM conditions as existing in residential, office and industrial buildings. This document addresses commonly known EMC related hazards and hazardous situations relevant to lifts, escalators and moving walks when they are used as intended and under the conditions foreseen by the lift installer or escalator and/or moving walk manufacturer. It is assumed that no ports connected to safety circuit only are rated at currents greater than 100 amps. It is assumed that mobile telephones and radio transmitters used at frequencies and power of that stated in Table 1 are not placed within 200 mm distance from safety circuit(s). However: — performance criteria and test levels for apparatus/assembly of apparatus used in general function circuits do not cover situations with an extremely low probability of occurrence; — this document does not apply to other apparatus already proven to be in conformity to the EMC national regulation, and not related to the safety of the lift, escalator or moving walk, such as lighting apparatus, communication apparatus, etc. This document does not apply to electromagnetic environments such as: — radio transmitter stations; — railways and metros; — heavy industrial plant; — electricity power stations; which need additional investigations. This document is not applicable to apparatus which were manufactured before the date of its publication.

  • Standard
    16 pages
    English language
    sale 15% off
  • Draft
    16 pages
    English language
    sale 15% off

This document specifies the requirements for solid wall pipes with smooth internal and external surfaces, extruded from the same formulation throughout the wall, fittings and the system of unplasticized poly(vinyl chloride) (PVC-U) piping systems intended for soil and waste discharge applications (low and high temperature):
-   inside buildings (application area code "B");
-   for both inside buildings and buried in ground within the building structure (application area code "BD").
NOTE 1   The intended use is reflected in the marking of products by "B" or "BD".
NOTE 2   Multilayer pipes with different formulations throughout the wall and foamed core pipes are covered by EN 1453-1 [1].
NOTE 3   For use buried in ground within the building structure are intended only those components (marked with "BD") with nominal outside diameters equal to or greater than 75 mm.
NOTE 4   EN 476 [2] specifies the general requirements for components used in discharge pipes, drains and sewers for gravity systems. Pipes and fittings conforming to this standard fully meet these requirements.
This document is also applicable to PVC-U pipes, fittings and the system intended for the following purposes:
-   ventilating part of the pipework in association with discharge applications;
-   rainwater pipework within the building structure.
This document also specifies the test parameters for the test method that are referred to.
This document covers a range of nominal sizes, a range of pipes and fittings series and gives recommendations concerning colours.
NOTE 5   It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
For external above ground application additional requirements depending on the climate should be agreed between the manufacturer and the user.
NOTE 6   Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex B can be used with pipes and fittings conforming to this document, provided they conform to the requirements for joint dimensions given in Clause 6 and to the requirements of Table 25.

  • Standard
    46 pages
    English language
    sale 10% off
    e-Library read for
    1 day