91.140.01 - Installations in buildings in general
ICS 91.140.01 Details
Installations in buildings in general
Gebaudeinstallationen im allgemeinen
Installations dans les bâtiments en général
Napeljave v stavbah na splošno
General Information
ISO 16032:2004 specifies methods for measuring the sound-pressure level produced by service equipment attached to or installed in buildings. It specifically covers measurements on sanitary installations, mechanical ventilation, heating and cooling service equipment, lifts, rubbish chutes, boilers, blowers, pumps and other auxiliary service equipment, and motor-driven car park doors, but can also be applied to other equipment attached to or installed in buildings.
The methods are suitable for rooms with volumes of approximately 300 cubic metres or less in e.g. dwellings, hotels, schools, offices and hospitals. The standard is not in general intended for measurements in large auditoria such as concert halls. However, the operating conditions and operating cycles in Annex B can be used in such cases.
The service equipment sound-pressure level is determined as the maximum A-weighted and optionally C-weighted sound-pressure level occurring during a specified operation cycle of the service equipment under test, or as the equivalent continuous sound-pressure level determined with a specified integration time. A-weighted and C-weighted values are calculated from octave-band measurements.
- Standard29 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies an engineering method for the measurement of sound pressure levels in rooms from service equipment installed in the building.
This document covers specifically measurements of sound from sanitary installations, mechanical ventilation, heating and cooling service equipment, lifts, rubbish chutes, heating devices, blowers, pumps and other auxiliary service equipment, and motor driven car park doors. It can also be applied to measurements of sounds from other types of equipment or activities within the building, e.g. noise from sport facilities or restaurants.
The measurement of noise from external sound sources generating air-borne or ground-borne noise in the building are not included in this document.
The methods are suitable for rooms with volumes of approximately 300 m3 or less for instance, in dwellings, hotels, schools, offices and hospitals.
The methods are not intended for measurements in large auditoria or concert halls.
- Standard29 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies an engineering method for the measurement of sound pressure levels in rooms from service equipment installed in the building. This document covers specifically measurements of sound from sanitary installations, mechanical ventilation, heating and cooling service equipment, lifts, rubbish chutes, heating devices, blowers, pumps and other auxiliary service equipment, and motor driven car park doors. It can also be applied to measurements of sounds from other types of equipment or activities within the building, e.g. noise from sport facilities or restaurants. The measurement of noise from external sound sources generating air-borne or ground-borne noise in the building are not included in this document. The methods are suitable for rooms with volumes of approximately 300 m3 or less for instance, in dwellings, hotels, schools, offices and hospitals. The methods are not intended for measurements in large auditoria or concert halls.
- Standard20 pagesEnglish languagesale 15% off
- Standard22 pagesFrench languagesale 15% off
This document specifies control applications and function blocks focusing on but not limited to lighting, solar protection and HVAC applications.
It describes how energy performance, comfort, and operational requirements of buildings are translated into functional specifications for integrated plant and room control.
- Standard157 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard provides mechanisms through which various vendors of building automation, control, and building management systems may exchange information in a standardized way.
This document provides specifications for the Application Elements of Control Network Protocol packets as follows:
- definitions of standardized packet (network-variable) data types;
- definitions of device-interface files;
- definitions of standardized configuration-property types;
- definitions of standardized enumeration types;
- definitions of standardized functional profiles;
- definition of the standardized method of file transfer between devices.
The purpose of this specification is to ensure interoperability between various CNP implementations. This document contains all the information necessary to read and interpret the format of data and control information that is used by EN 14908-5. It also defines the device interface for a device as specified, which is necessary to exchange data between various devices from different manufacturers.
- Standard564 pagesEnglish languagesale 10% offe-Library read for1 day
This document gives rules for the calculation of heat-transfer-related properties of building equipment and industrial installations, predominantly under steady-state conditions. This document also gives a simplified approach for the calculation of thermal bridges.
- Standard60 pagesEnglish languagesale 10% offe-Library read for1 day
This document provides mechanisms through which various vendors of building automation, control, and building management systems may exchange information in a standardized way.
This document provides specifications for the Application Elements of Control Network Protocol packets as follows:
- definitions of standardized packet (network-variable) data types;
- definitions of device-interface files;
- definitions of standardized configuration-property types;
- definitions of standardized enumeration types;
- definitions of standardized functional profiles;
- definition of the standardized method of file transfer between devices.
The purpose of this document is to ensure interoperability between various CNP implementations. This document contains all the information necessary to read and interpret the format of data and control information that is used by EN 14908 5. It also defines the device interface for a device as specified, which is necessary to exchange data between various devices from different manufacturers.
- Standard564 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies control applications and function blocks focusing on but not limited to lighting, solar protection and HVAC applications.
It describes how energy performance, comfort, and operational requirements of buildings are translated into functional specifications for integrated plant and room control.
- Standard157 pagesEnglish languagesale 10% offe-Library read for1 day
This document gives rules for the calculation of heat-transfer-related properties of building equipment
and industrial installations, predominantly under steady-state conditions. This document also gives a
simplified approach for the calculation of thermal bridges
- Standard60 pagesEnglish languagesale 10% offe-Library read for1 day
This document gives rules for the calculation of heat-transfer-related properties of building equipment and industrial installations, predominantly under steady-state conditions. This document also gives a simplified approach for the calculation of thermal bridges.
- Standard52 pagesEnglish languagesale 15% off
- Standard54 pagesFrench languagesale 15% off
This document specifies an adaptation layer for the control network protocol (CNP), as described in EN 14908 1 to utilize wireless communication network. This document defines the services of the wireless communication provided to CNP layer for delivering data and commands towards and from sensors, actuators, etc. which are wirelessly connected as part of the EN 14908 1 network.
In addition, this document defines the requirements for the radio communication applicable for CNP layer operation.
For the radio communication different frequency bands can be utilized. Annex A defines requirement for operation in different frequency bands.
- Standard29 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies a communication protocol for networked control systems. The protocol provides peer-to-peer communication for networked control using web-services. This document describes services in layer 1 and layer 2.
The layer 1 (physical layer) specification describes the MAC sub-layer interface to the physical layer. The layer 2 (data link layer), as described in EN 14908 1, is integrated in UDP/IP communication using IPv4 and IPv6 protocols.
- Standard18 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies field survey methods for measuring
a) airborne sound insulation between rooms,
b) impact sound insulation of floors,
c) airborne sound insulation of façades, and
d) sound pressure levels in rooms caused by service equipment.
The methods described in this document are applicable for measurements in rooms of dwellings or in rooms of comparable size with a maximum of 150 m3.
For airborne sound insulation, impact sound insulation and façade sound insulation the method gives values which are (octave band) frequency dependent. They can be converted into a single number characterising the acoustical performances by application of ISO 717-1 and ISO 717-2. For heavy/soft impact sound insulation, the results also are given as A-weighted maximum impact sound pressure level. For service equipment sound the results are given directly in A - or C -weighted sound pressure levels.
- Standard41 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies an adaptation layer for the control network protocol (CNP), as described in EN 14908 1 to utilize wireless communication network. This document defines the services of the wireless communication provided to CNP layer for delivering data and commands towards and from sensors, actuators, etc. which are wirelessly connected as part of the EN 14908 1 network.
In addition, this document defines the requirements for the radio communication applicable for CNP layer operation.
For the radio communication different frequency bands can be utilized. Annex A defines requirement for operation in different frequency bands.
- Standard29 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies a communication protocol for networked control systems. The protocol provides peer-to-peer communication for networked control using web-services. This document describes services in layer 1 and layer 2.
The layer 1 (physical layer) specification describes the MAC sub-layer interface to the physical layer. The layer 2 (data link layer), as described in EN 14908 1, is integrated in UDP/IP communication using IPv4 and IPv6 protocols.
- Standard18 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies field survey methods for measuring
a) airborne sound insulation between rooms,
b) impact sound insulation of floors,
c) airborne sound insulation of façades, and
d) sound pressure levels in rooms caused by service equipment.
The methods described in this document are applicable for measurements in rooms of dwellings or in
rooms of comparable size with a maximum of 150 m3.
For airborne sound insulation, impact sound insulation and façade sound insulation the method gives
values which are (octave band) frequency dependent. They can be converted into a single number
characterising the acoustical performances by application of ISO 717-1 and ISO 717-2. For heavy/soft
impact sound insulation, the results also are given as A-weighted maximum impact sound pressure
level. For service equipment sound the results are given directly in A - or C -weighted sound pressure
levels.
- Standard41 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies field survey methods for measuring a) airborne sound insulation between rooms, b) impact sound insulation of floors, c) airborne sound insulation of façades, and d) sound pressure levels in rooms caused by service equipment. The methods described in this document are applicable for measurements in rooms of dwellings or in rooms of comparable size with a maximum of 150 m3. For airborne sound insulation, impact sound insulation and façade sound insulation the method gives values which are (octave band) frequency dependent. They can be converted into a single number characterising the acoustical performances by application of ISO 717-1 and ISO 717-2. For heavy/soft impact sound insulation, the results also are given as A-weighted maximum impact sound pressure level. For service equipment sound the results are given directly in A - or C -weighted sound pressure levels.
- Standard33 pagesEnglish languagesale 15% off
- Standard33 pagesEnglish languagesale 15% off
- Standard34 pagesFrench languagesale 15% off
- Standard34 pagesFrench languagesale 15% off
This standard provides a comprehensive set of procedures for verifying the correct implementation of each capability claimed on a BACnet PICS including:
(a) support of each claimed BACnet service, either as an initiator, executor, or both,
(b) support of each claimed BACnet object-type, including both required properties and each claimed optional property,
(c) support of the BACnet network layer protocol,
(d) support of each claimed data link option, and
(e) support of all claimed special functionality.
- Standard735 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard735 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies a communication protocol for networked control systems. The protocol provides peer-to-peer communication for networked control using web-services. The document describes services in layer 2 and layer 3.
The layer 2 (data link layer) specification also describes the MAC sub-layer interface to the physical layer. The physical layer provides a choice of transmission media. The layer 3 (network layer), as described in EN 14908 1, is integrated in UDP/IP communication using IPv4 and IPv6 protocols.
- Standard49 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies a communication protocol for networked control systems. The protocol provides peer-to-peer communication for networked control using web-services. The standard describes services in layer 2 and layer 3.
The layer 2 (data link layer) specification also describes the MAC sub-layer interface to the physical layer. The physical layer provides a choice of transmission media. The layer 3 (network layer), as described in EN 14908-1, is integrated in UDP/IP communication using IPv4 and IPv6 protocols.
- Standard49 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies requirements for indoor environmental parameters for thermal environment, indoor air quality, lighting and acoustics and specifies how to establish these parameters for building system design and energy performance calculations.
This European Standard includes design criteria for the local thermal discomfort factors, draught, radiant temperature asymmetry, vertical air temperature differences and floor surface temperature.
This European Standard is applicable where the criteria for indoor environment are set by human occupancy and where the production or process does not have a major impact on indoor environment.
This European Standard also specifies occupancy schedules to be used in standard energy calculations and how different categories of criteria for the indoor environment can be used.
The criteria in this European Standard can also be used in national calculation methods. This standard sets criteria for the indoor environment based on existing standards and reports listed under normative references or in the bibliography.
This European Standard does not specify design methods, but gives input parameters to the design of building envelope, heating, cooling, ventilation and lighting.
Table 1 shows the relative position of this standard within the set of EPB standards in the context of the modular structure as set out in EN ISO 52000 1.
NOTE 1 In CEN ISO/TR 52000 2 the same table can be found, with, for each module, the numbers of the relevant EPB standards and accompanying technical reports that are published or in preparation.
NOTE 2 The modules represent EPB standards, although one EPB standard may cover more than one module and one module may be covered by more than one EPB standard, for instance a simplified and a detailed method respectively. See also Clause 2 and Tables A.1 and B.1.
- Standard79 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard88 pagesGerman languagesale 10% offe-Library read for1 day
This document deals with the indoor environmental parameters for thermal environment, indoor air quality, lighting and acoustic. The document explains how to use EN 16798-1 for specifying indoor environmental input parameters for building system design and energy performance calculations. The document specifies methods for long term evaluation of the indoor environment obtained as a result of calculations or measurements. The document specifies criteria for measurements which can be used if required to measure compliance by inspection. The Document identifies parameters to be used by monitoring and displaying the indoor environment in existing buildings. This document is applicable where the criteria for indoor environment are set by human occupancy and where the production or process does not have a major impact on indoor environment. The document explains how different categories of criteria for the indoor environment can be used.
- Technical report88 pagesEnglish languagesale 10% offe-Library read for1 day
ISO 15758:2014 specifies a method for calculating the density of the water vapour flow rate in cold pipe insulation systems, and the total amount of water diffused into the insulation over time. The calculation method presupposes that water vapour can only migrate into the insulation system by diffusion, with no contribution from airflow. It also assumes the use of homogeneous, isotropic insulation materials so that the water vapour partial pressure is constant at all points equidistant from the axis of the pipe.
ISO 15758:2014 is applicable when the temperature of the medium in the pipe is above 0 °C. It applies to pipes inside buildings as well as in the open air.
- Standard23 pagesEnglish languagesale 10% offe-Library read for1 day
ISO 15758:2014 specifies a method for calculating the density of the water vapour flow rate in cold pipe insulation systems, and the total amount of water diffused into the insulation over time. The calculation method presupposes that water vapour can only migrate into the insulation system by diffusion, with no contribution from airflow. It also assumes the use of homogeneous, isotropic insulation materials so that the water vapour partial pressure is constant at all points equidistant from the axis of the pipe. ISO 15758:2014 is applicable when the temperature of the medium in the pipe is above 0 °C. It applies to pipes inside buildings as well as in the open air.
- Standard15 pagesEnglish languagesale 15% off
- Standard15 pagesEnglish languagesale 15% off
- Standard15 pagesFrench languagesale 15% off
- Standard15 pagesFrench languagesale 15% off
This European Standard specifies the control network protocol (CNP) free-topology twisted-pair channel for networked control systems in commercial Building Automation, Controls and Building Management and is used in conjunction with EN 14908-1:2014. The channel supports communication at 78,125 kbit/s between multiple nodes, each of which consists of a transceiver, a protocol processor, an application processor, a power supply, and application electronics.
This European Standard covers the complete physical layer (OSI Layer 1), including the interface to the Media Access Control (MAC) sub-layer and the interface to the medium. Parameters that are controlled by other layers but control the operation of the physical layer are also specified.
- Standard19 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the transporting of the Control Network Protocol (CNP) packets for commercial Building Automation, Controls and Building Management over Internet Protocol (IP) networks using a tunnelling mechanism wherein the CNP packets are encapsulated within IP packets. It applies to both CNP nodes and CNP routers.
The purpose of this European Standard is to ensure interoperability between various CNP devices that wish to use IP networks to communicate using the CNP protocol.
The main body of this European Standard is independent of the CNP protocol being transported over the IP network. The reader is directed to Annex A and Annex B for the normative and informative, respectively, aspects of this specification that are specific to EN 14908-1.
Figure 1 shows a possible configuration of such CNP devices and networks connected to an IP network.
Figure 1 depicts two types of CNP devices: CNP nodes and CNP routers. It should be noted that the routers shown can route packets between typical CNP channels (such as twisted pair or power line) and an IP channel or it can route CNP packets between two IP channels. In this European Standard the IP channel will be defined in such a way to allow it to be used like any other CNP channel.
In the above diagram, the IP network can be considered to be one or more IP channels. This European Standard covers only how CNP packets are transported over IP channels. It does not cover how CNP packets are routed between standard CNP channels and IP channels. This specification is not intended to cover the lower layers (physical, MAC and link layers) of either standard CNP or IP channels.
- Standard62 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies all the information necessary to facilitate the exchange of data and control information over the power line medium for networked control systems in commercial Building Automation, Controls and Building Management.
This European Standard establishes a minimal set of rules for compliance. It does not rule out extended services to be provided, given that the rules are adhered to within the system. It is the intention of the standard to permit extended services (defined by users) to coexist.
Certain aspects of this standard are defined in other documents. These documents are referenced where relevant. In the case where a referenced standard conflicts with this European Standard, this part of EN 14908 will prevail.
- Standard15 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard applies to a communication protocol for networked control systems in commercial Building Automation, Controls and Building Management. The protocol provides peer-to-peer communication for networked control and is suitable for implementing both peer-to-peer and master-slave control strategies. This specification describes services in layers 2 to 7. In the layer 2 (data link layer) specification, it also describes the MAC sub-layer interface to the physical layer. The physical layer provides a choice of transmission media. The interface described in this specification supports multiple transmission media at the physical layer. In the layer 7 specification, it includes a description of the types of messages used by applications to exchange application and network management data.
- Standard415 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard gives guidelines for performance benchmarking and contains clear terms and definitions as well as methods for benchmarking facility management products and services as well as facility management organisations and operations.
This European Standard establishes a common basis for benchmarking facility management costs, floor areas and environmental impacts as well as service quality, satisfaction and productivity.
This European Standard is applicable to Facility Management as defined in EN 15221-1 and detailed in EN 15221-4.
- Standard68 pagesEnglish languagesale 10% offe-Library read for1 day
This part of ISO 10295 provides guidance in respect of a structured method of characterizing the penetrating seal under test utilizing a series of defined parameters, each one being determined by the use of a selected series of test configurations in conjunction with simulated services. The level of characterization being sought is dependent upon the classification requirement of the system, which in turn determines the complexity of the test program. It is also intended the test method addresses the influence the supporting construction has on the performance of the seal system. The methods described apply to the determination of data relating to single component penetration seals where the penetration service does not melt out within the appropriate period of exposure to a fully developed fire. The selection of the appropriate system depends upon many factors. Of particular importance is the size of the penetration, since penetration seal systems are frequently penetration size (or size range) specific. This is a guidance document, its purpose being to determine the critical parameters relating to the performance of the seal being evaluated. Such parameters can then be used as a basis for interpolation and/or extrapolation of the seal's performance. The procedures used have been developed utilizing small square penetrations, single component penetration seals, and cylindrical conductors; however it is possible to generate a similar series of tests using rectangular cross-section conductors if this is more appropriate to end use. This part of ISO 10295 provides a structured approach designed to establish — the mode of failure; — the parameters critical to the performance of the penetration seal under test. The mode of failure and critical parameters are ascertained using test configurations appropriate to the potential performance of the product, in conjunction with clearly defined standard penetrations. The results gained from the application of this technical report are designed to assist a suitably qualified person to develop a direct and extended field of application for the penetration seal under test using in particular, the principles and methodology given in ISO/TR 12470. Using the field(s) of application so generated, it should be possible to classify the penetration seal, thus facilitating its incorporation into specifications. The test configurations recommended in this part of ISO 10295 are not appropriate for evaluating multicomponent penetration seals. This part of ISO 10295 is not appropriate for characterizing all types of penetration seals, e.g. pipe closers/collars and some gland systems, for which evaluation using ISO 10295-1 is more appropriate. This part of ISO 10295 does not address the distance required between services that can generate their own heat. When a live service is being evaluated, it is necessary to give consideration to the distance required between penetrations.
- Technical report18 pagesEnglish languagesale 15% off
This European Standard establishes a common basis for planning and design, area and space management, financial assessment, as well as a tool for benchmarking in the field of Facility Management.
This standard covers area and space measurement for existing owned or leased buildings as well as buildings in state of planning or development.
This standard presents a framework for measuring floor areas within buildings and areas outside of buildings. In addition, it contains clear terms and definitions as well as methods for measuring horizontal areas and volumes in buildings and/or parts of buildings, independent of their function.
- Standard50 pagesEnglish languagesale 10% offe-Library read for1 day
This European standard provides guidance to FM organisations on the development and improvement of their processes to support the primary processes.
This standard also sets out basic principles, describes high-level generic FM processes, lists strategic, tactical and operational processes and provides examples of process workflows.
This standard is written from a primary processes, demand perspective for an audience of all stakeholders in FM processes.
- Standard43 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard provides a guideline how to measure, achieve and improve quality in FM. It gives complementary guidelines to EN ISO 9000, EN ISO 9001 and EN 15221-2 within the framework of EN 15221 1. The standard provides a link into management methods and management theories.
This European Standard is applicable to:
- FM in public and private organizations;
- client organization and service provider relationships;
- full range of facility products or facility services;
- both types of service providers in FM (internal and external);
- all types of working environments (e.g. industrial, commercial, administration, military, healthcare etc.).
This European Standard is applicable to business services (not consumer oriented).
This European Standard does not:
- replace the quality management systems of the client organization;
- provide standard forms:
- for performance and quality management systems (delivering a quality management system);
- for defining requirements;
- for a measurement tool;
- for service level;
- apply to the certification of the quality system of Facility Management (covered by EN ISO 9001).
- Standard44 pagesEnglish languagesale 10% offe-Library read for1 day
FM covers and integrates a very broad scope of processes, products / services, activities and facilities. The approach of this standard is to consider the added value provided to the primary activities by adopting a product perspective as recognised by the primary processes or core business in the organisation. This standard therefore introduces the concept of standardised (classified) facility products.
The scope of this standard is to provide taxonomy for FM which includes:
- relevant interrelationship of elements and their structures in FM;
- definitions of terms and contents to standardise facility products which provide a basis for cross border trade, data management, cost allocation and benchmarking;
- a high level classification and hierarchical coding structure for the standardised facility products;
- expanding the basic FM model given in EN 15221-1 by adding a time scale in the form of the quality cycle called PDCA (Plan, Do, Check, Act);
- a linkage to existing cost and facilities structures;
- alignment with the primary activities requirements.
Additional benefits from this standard are:
- Introducing a client rather than a specifically asset oriented view;
- harmonisation of different existing national structures (e.g. building cost codes) on an upper level relevant for the organisation and its primary activities.
- Standard82 pagesEnglish languagesale 10% offe-Library read for1 day
This specification contains all the information necessary to facilitate the exchange of data and control information in an interoperable fashion using EN 14908-1 and its associated data-transport media specifications.
This specification establishes a minimal set of rules for compliance. It does not rule-out extended services to be provided, given that the rules are adhered-to within the system. It is the intention of the standard to permit extended services to coexist and defines the bounds in which those services function, including the format for internal device-documentation of those services. Services outside purvey of this specification so long as they are adherents of the system are permitted but will not necessarily be interoperable with any other devices and shall not be essential for the functioning of the device.
Certain aspects of this standard are defined in other documents. These documents are referenced where relevant. In the case where a referenced standard conflicts with this document, this document will prevail.
- Standard58 pagesEnglish languagesale 10% offe-Library read for1 day
ISO 10295-2:2009 specifies the heating conditions, methods of test and criteria for the evaluation of the ability of a linear joint seal to maintain the fire integrity and thermal insulation of a fire-separating element at the joint being sealed. The purpose of the tests is to assess the integrity and insulation performance of the linear joint seals, including the effects of induced movement in those cases where the joint is designed to accommodate movement and has a width greater than 20 mm. It is not the intention of this part of ISO 10295-2:2009 to provide quantitative information on the rate of leakage of smoke and/or gases, or on the transmission or generation of fumes, although such phenomena can be recorded in describing the general behaviour of specimens during the test. It is not the intention of this part of ISO 10295-2:2009 to evaluate joint seals where special test procedures already exist, e.g. doors, partitions, penetrations, pipes, ducts and cables.
- Standard24 pagesEnglish languagesale 15% off
ISO 10295-1:2007 specifies the heating condition, method of test and criteria for the evaluation of the ability of a penetration sealing system to maintain the integrity and insulation of a fire separating element at the position at which it has been penetrated, for example by a service. ISO 10295-1:2007 assesses the effect of such penetrations on the integrity and insulation performance of the element concerned, the integrity and insulation performance of the penetration sealing system, the insulation performance of the penetrating service or services, and where appropriate, the integrity failure of a service. ISO 10295-1:2007 does not provide information concerning the influence of the inclusion of such penetrations and sealing systems on the load-bearing capacity of the element. It is possible that a penetration seal is a component of, or contributes to the performance of, a system to which special requirements apply. In such cases additional tests, relevant to the system and its function, can be necessary. Examples are chimneys and fire-rated ducts in air distribution systems. ISO 10295-1:2007 is not intended to provide quantitative information on the rate of leakage of smoke and/or hot gases or on the transmission or generation of fumes. Such phenomena are to be noted in describing the general behaviour of specimens during test. ISO 10295-1:2007 does not provide information on the ability of the seal to withstand stresses that can be caused by the movement or displacement of the penetration services in practice.
- Standard14 pagesEnglish languagesale 15% off
- Standard18 pagesRussian languagesale 15% off
ISO 14617-15:2002 specifies graphical symbols for use on installation diagrams (e.g. for buildings) and network maps, supplementing the symbols specified in ISO 14617-2 to ISO 14617-12. Symbols on such diagrams are used mainly to indicate the location and type of a component or device.
- Standard14 pagesEnglish languagesale 15% off
- Standard13 pagesFrench languagesale 15% off
This document specifies an open and extensible standard for residential, commercial, and industrial control and automation applications using the EN 14908-1 control network protocol and related protocols (EN 14908-2 to EN 14908-9) to provision and manage IoT devices, to access and update data from the devices, and to aggregate data from diverse devices and protocols for delivery to external applications and services.
The web services as specified in this document are implemented on a central gateway or edge server that communicates with multiple sensor, actuator, and controller edge devices using one or more edge protocols such as EN 14908-1, and also interfaces with one or more enterprise and cloud services or applications.
- Draft452 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies control applications and function blocks focusing on but not limited to lighting, solar protection, and HVAC applications.
It describes how energy performance, comfort, and operational requirements of buildings are translated into functional specifications for integrated plant and room control.
- Draft166 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies an open and extensible standard for residential, commercial, and industrial control and automation applications using the EN 14908-1 control network protocol and related protocols (EN 14908-2 to EN 14908-9) to provision and manage IoT devices, to access and update data from the devices, and to aggregate data from diverse devices and protocols for delivery to external applications and services.
The web services as specified in this document are implemented on a central gateway or edge server that communicates with multiple sensor, actuator, and controller edge devices using one or more edge protocols such as EN 14908-1, and also interfaces with one or more enterprise and cloud services or applications.
- Draft452 pagesEnglish languagesale 10% offe-Library read for1 day
This draft European standard gives relevant terms and definitions in the area of Facility Management. It also provides a structure of facility services.
- Draft17 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the requirements of hardware and functions for products and systems for the control and management of the HVAC processes (Building Control and Automation System BAC), and provides for the integration of non HVAC processes.
- Draft71 pagesEnglish languagesale 10% offe-Library read for1 day
ISO 16032:2004 specifies methods for measuring the sound-pressure level produced by service equipment attached to or installed in buildings. It specifically covers measurements on sanitary installations, mechanical ventilation, heating and cooling service equipment, lifts, rubbish chutes, boilers, blowers, pumps and other auxiliary service equipment, and motor-driven car park doors, but can also be applied to other equipment attached to or installed in buildings.
The methods are suitable for rooms with volumes of approximately 300 cubic metres or less in e.g. dwellings, hotels, schools, offices and hospitals. The standard is not in general intended for measurements in large auditoria such as concert halls. However, the operating conditions and operating cycles in Annex B can be used in such cases.
The service equipment sound-pressure level is determined as the maximum A-weighted and optionally C-weighted sound-pressure level occurring during a specified operation cycle of the service equipment under test, or as the equivalent continuous sound-pressure level determined with a specified integration time. A-weighted and C-weighted values are calculated from octave-band measurements.
- Standard23 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard provides mechanisms through which various vendors of building automation, control, and building management systems may exchange information in a standardized way.
This document provides specifications for the Application Elements of Control Network Protocol packets as follows:
- definitions of standardized packet (network-variable) data types;
- definitions of device-interface files;
- definitions of standardized configuration-property types;
- definitions of standardized enumeration types;
- definitions of standardized functional profiles;
- definition of the standardized method of file transfer between devices.
The purpose of this specification is to ensure interoperability between various CNP implementations. This document contains all the information necessary to read and interpret the format of data and control information that is used by EN 14908-5. It also defines the device interface for a device as specified, which is necessary to exchange data between various devices from different manufacturers.
- Standard629 pagesEnglish languagesale 10% offe-Library read for1 day
This document provides a synopsis of graphical symbols which are intended to be placed on building equipments and/or technical documentation of products in order to instruct the person(s) using the equipments.
These graphical symbols are primary intended:
to identify control or automation or technical management equipments or part of these equipments: electronic devices (e.g. controller, scheduler, optimiser, etc.), sensors, actuators,
to indicate functions and their operating modes,
to indicate settings for modes and functions parameters introduction,
to designate connexions,
to provide instruction to users (professional and/or end user) for the operation of the equipment.
The graphical symbols in this document are not primarily intended for:
safety signs,
public information,
schematics for systems principles.
- Technical specification24 pagesEnglish languagesale 10% offe-Library read for1 day
The document provides a structure of Building Management (BM) and its Building Services and gives terms and definitions in the field of Building Management for general understanding. The document does not purport to describe Building Management Systems.
- Technical specification19 pagesEnglish languagesale 10% offe-Library read for1 day
- Amendment99 pagesEnglish languagesale 10% offe-Library read for1 day
- Amendment99 pagesEnglish languagesale 10% offe-Library read for1 day
The purpose of ISO 16484-5:2017 is to define data communication services and protocols for computer equipment used for monitoring and control of HVAC&R and other building systems and to define, in addition, an abstract, object-oriented representation of information communicated between such equipment, thereby facilitating the application and use of digital control technology in buildings.
- Standard1342 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard1342 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard is applicable to specific energy audit requirements in buildings. It specifies the requirements, methodology and deliverables of an energy audit in a building or group of buildings, excluding individual private dwellings. It shall be applied in conjunction with, and is supplementary to, EN 16247 1, Energy audits - Part 1: General requirements. It provides additional requirements to EN 16247 1 and shall be applied simultaneously.
If processes are included in the scope of the energy audit, the energy auditor may choose to apply EN 16247 3, Energy audits - Part 3: Processes. If on-site transport on a site is included in the scope of the energy audit, the energy auditor may choose to apply EN 16247 4, Energy audits - Part 4: Transport.
NOTE This standard may cover multi-dwelling apartment blocks where communal services are supplied from a landlord. It is not intended for individual dwellings and single family houses.
- Standard44 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard – translation41 pagesSlovenian languagesale 10% offe-Library read for1 day