ASTM A376/A376M-02

Standard Specification for Seamless Austenitic Steel Pipe for High-Temperature Central-Station Service

SCOPE
1.1 This specification covers seamless austenitic steel pipe intended for high-temperature central-station service. Among the grades covered are five H grades and two nitrogen grades (304N and 316N) that are specifically intended for high-temperature service.  
1.2 Optional supplementary requirements (S1 through S10) are provided. These supplementary requirements specify additional tests that will be made only when stated in the order, together with the number of such tests required.
1.3 Grades TP321 and TP321H have lower strength requirements for nominal wall thicknesses greater than 3/8 in. [9.5 mm].  
1.4 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. The inch-pound units shall apply unless the "M" designation of this specification is specified in the order.  
Note 1—The dimensionless designator NPS (nominal pipe size) has been substituted in this standard for such traditional terms as "nominal diameter," "size," and "nominal size."

General Information

• Status: Historical
• Publication Date: 09-Mar-2002
• ICS: 23.040.10 - Iron and steel pipes
• Technical Committee: A01 - Steel, Stainless Steel and Related Alloys
• Drafting Committee: A01.10 - Stainless and Alloy Steel Tubular Products

Relations

• Replaces: ASTM A376/A376M-01a - Standard Specification for Seamless Austenitic Steel Pipe for High-Temperature Central-Station Service
• Effective Date: 10-Mar-2002
• Replaced By: ASTM A376/A376M-02a - Standard Specification for Seamless Austenitic Steel Pipe for High-Temperature Central-Station Service
• Effective Date: 10-Sep-2002
• Referred By: ASTM D3930-08(2023) - Standard Specification for Adhesives for Wood-Based Materials for Construction of Manufactured Homes
• Effective Date: 10-Mar-2002
• Referred By: ASTM A999/A999M-23 - Standard Specification for General Requirements for Alloy and Stainless Steel Pipe
• Effective Date: 10-Mar-2002
• Referred By: ASTM C852/C852M-17(2022) - Standard Guide for Design Criteria for Plutonium Gloveboxes
• Effective Date: 10-Mar-2002

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Please contact ASTM International (www.astm.org) for the latest information.
An American National Standard
Designation: A 376/A 376M – 02 Used in USDOE-NE standards
Standard Specification for
Seamless Austenitic Steel Pipe for High-Temperature
1
Central-Station Service
This standard is issued under the fixed designationA 376/A 376M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (ϵ) indicates an editorial change since the last revision or reapproval.
5
1. Scope* E112 Test Methods for Determining Average Grain Size
2 E 213 Practice for Ultrasonic Examination of Metal Pipe
1.1 This specification covers seamless austenitic steel pipe
6
and Tubing
intended for high-temperature central-station service. Among
E 381 Method of Macroetch Testing Steel Bars, Billets,
the grades covered are five H grades and two nitrogen grades
5
Blooms, and Forgings
(304N and 316N) that are specifically intended for high-
E 426 Practice for Electromagnetic (Eddy-Current) Exami-
temperature service.
nation of Seamless and Welded Tubular Products, Auste-
1.2 Optional supplementary requirements (S1 through S10)
6
nitic Stainless Steel, and Similar Alloys
are provided. These supplementary requirements specify addi-
2.2 ASME Boiler and Pressure Vessel Code:
tional tests that will be made only when stated in the order,
7
Section IX Welding Qualifications
together with the number of such tests required.
2.3 Other Standards:
1.3 GradesTP321 andTP321H have lower strength require-
SNT-TC-1A Personnel Qualification and Certification in
3
ments for nominal wall thicknesses greater than ⁄8 in. [9.5
8
Nondestructive Testing
mm].
1.4 The values stated in either inch-pound units or SI units
3. Terminology
are to be regarded separately as standard. Within the text, the
3.1 Definitions—For definitions of terms used in this speci-
SI units are shown in brackets. The values stated in each
fication, refer to Terminology A 941A 941.
system are not exact equivalents; therefore, each system must
be used independently of the other. Combining values from the
4. Ordering Information
two systems may result in nonconformance with the specifi-
4.1 Orders for material to this specification should include
cation. The inch-pound units shall apply unless the “M”
the following, as required to describe the desired material
designation of this specification is specified in the order.
adequately:
NOTE 1—The dimensionless designator NPS (nominal pipe size) has
4.1.1 Quantity (feet, centimetres, or number of lengths),
been substituted in this standard for such traditional terms as “nominal
4.1.2 Name of material (seamless austenitic steel pipe),
diameter,” “size,” and “nominal size.”
4.1.3 Grade (Table 1),
4.1.4 Size (nominal size, or outside diameter and schedule
2. Referenced Documents
number or average wall thickness),
2.1 ASTM Standards:
4.1.5 Lengths (specific or random), (Permissible Variations
A 262 Practices for Detecting Susceptibility to Intergranu-
in Length Section of Specification A 999/A 999MA 999/
3
lar Attack in Austenitic Stainless Steels
A 999M),
A 941 Terminology Relating to Steel, Stainless Steel, Re-
4.1.6 End finish (Ends Section of Specification A 999/
4
lated Alloys, and Ferroalloys
A 999MA 999/A 999M),
A 999/A 999M Specification for General Requirements for
4.1.7 Optional requirements (Section 9) (see Hydrostatic
4
Alloy and Stainless Steel Pipe
Test Requirements Section and the Permissible Variation in
Weight for Seamless Pipe Section for weighing individual
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel,
Stainless Steel, and RelatedAlloys and is the direct responsibility of Subcommittee
A01.10 on Stainless and Alloy Steel Tubular Products.
5
Current edition approved Mar. 10, 2002. Published May 2002. Originally Annual Book of ASTM Standards, Vol 03.01.
6
published as A 376 – 54 T. Last previous edition A 376/A 376M – 01a. Annual Book of ASTM Standards, Vol 03.03.
2 7
For ASME Boiler and Pressure Vessel Code applications see related Specifi- Available from American Society of Mechanical Engineers (ASME Interna-
cation SA-376 in Section II of that Code. tional), Three Park Ave., New York, NY 10016-5990.
3 8
Annual Book of ASTM Standards, Vol 01.03. Available from the American Society for Nondestructive Testing, P.O. Box
4
Annual Book of ASTM Standards, Vol 01.01. 28518, 1711 Arlingate Ln., Columbus, OH 43228-0518.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Please contact ASTM Int
...