iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D5498-12

(Guide)

Standard Guide for Developing a Training Program for Personnel Performing Coating and Lining Work Inspection for Nuclear Facilities

Standard Guide for Developing a Training Program for Personnel Performing Coating and Lining Work Inspection for Nuclear Facilities

SIGNIFICANCE AND USE
Personnel trained for coating and lining work inspection are required to perform examination/inspection tasks to verify conformance of coating and lining work to written requirements.
This guide provides guidance for development of an indoctrination and training program for training of personnel performing coating and lining work inspection.
Certification/qualification of personnel performing coating and lining work inspection is addressed in Guide D4537.
SCOPE
1.1 This guide is intended to assist those responsible for developing a program for the indoctrination and training of personnel performing coating and lining inspection work for nuclear facilities.
1.2 It is recognized that organizations and job responsibilities vary widely among utilities and also among various support and service companies. It is the responsibility of the user of this guide to identify the appropriate subject matter for its program and its specific needs.
1.3 Users of this guide must ensure that coating and lining work complies not only with this guide, but also with the licensee's plant-specific quality assurance program and licensing commitments.

General Information

Status
Historical
Publication Date
29-Feb-2012
ICS
27.120.20 - Nuclear power plants. Safety
Technical Committee
D33 - Protective Coating and Lining Work for Power Generation Facilities
Drafting Committee
D33.04 - Quality Systems and Inspection
Current Stage
Ref Project

Relations

Replaces
ASTM D5498-09 - Standard Guide for Developing a Training Program for Personnel Performing Coating Work Inspection for Nuclear Facilities
Effective Date
01-Mar-2012
Replaced By
ASTM D5498-12a - Standard Guide for Developing a Training Program for Personnel Performing Coating and Lining Work Inspection for Nuclear Facilities
Effective Date
01-Nov-2012
Referred By
ASTM D4537-12(2018) - Standard Guide for Establishing Procedures to Qualify and Certify Personnel Performing Coating and Lining Work Inspection in Nuclear Facilities
Effective Date
01-Mar-2012
Referred By
ASTM D5163-16(2021) - Standard Guide for Establishing a Program for Condition Assessment of Coating Service Level I Coating Systems in Nuclear Power Plants
Effective Date
01-Mar-2012

Buy Standard

ASTM D5498-12 - Standard Guide for Developing a Training Program for Personnel Performing Coating and Lining Work Inspection for Nuclear FacilitiesASTM D5498-12 - Standard Guide for Developing a Training Program for Personnel Performing Coating and Lining Work Inspection for Nuclear Facilities
PreviousNext
Guide
ASTM D5498-12 - Standard Guide for Developing a Training Program for Personnel Performing Coating and Lining Work Inspection for Nuclear Facilities
English language
4 pages
sale 15% off
Preview
sale 15% off
Preview
REDLINE ASTM D5498-12 - Standard Guide for Developing a Training Program for Personnel Performing Coating and Lining Work Inspection for Nuclear FacilitiesREDLINE ASTM D5498-12 - Standard Guide for Developing a Training Program for Personnel Performing Coating and Lining Work Inspection for Nuclear Facilities
PreviousNext
Guide
REDLINE ASTM D5498-12 - Standard Guide for Developing a Training Program for Personnel Performing Coating and Lining Work Inspection for Nuclear Facilities
English language
4 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D5498 − 12
StandardGuide for
Developing a Training Program for Personnel Performing
1
Coating and Lining Work Inspection for Nuclear Facilities
This standard is issued under the fixed designation D5498; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope D3843 Practice for Quality Assurance for Protective Coat-
ings Applied to Nuclear Facilities
1.1 This guide is intended to assist those responsible for
D3925 Practice for Sampling Liquid Paints and Related
developing a program for the indoctrination and training of
Pigmented Coatings
personnel performing coating and lining inspection work for
D4138 Practices for Measurement of Dry Film Thickness of
nuclear facilities.
Protective Coating Systems by Destructive, Cross-
1.2 It is recognized that organizations and job responsibili-
Sectioning Means
ties vary widely among utilities and also among various
D4212 Test Method for Viscosity by Dip-Type Viscosity
support and service companies. It is the responsibility of the
Cups
user of this guide to identify the appropriate subject matter for
D4214 Test Methods for Evaluating the Degree of Chalking
its program and its specific needs.
of Exterior Paint Films
1.3 Users of this guide must ensure that coating and lining
D4258 Practice for Surface Cleaning Concrete for Coating
work complies not only with this guide, but also with the
D4259 Practice for Abrading Concrete
licensee’s plant-specific quality assurance program and licens-
D4260 Practice for Liquid and Gelled Acid Etching of
ing commitments.
Concrete
D4261 Practice for Surface Cleaning Concrete Masonry
2. Referenced Documents
2 Units for Coating
2.1 ASTM Standards:
D4262 TestMethodforpHofChemicallyCleanedorEtched
D16 TerminologyforPaint,RelatedCoatings,Materials,and
Concrete Surfaces
Applications
D4263 Test Method for Indicating Moisture in Concrete by
D610 Practice for Evaluating Degree of Rusting on Painted
the Plastic Sheet Method
Steel Surfaces
D4285 Test Method for Indicating Oil or Water in Com-
D714 Test Method for Evaluating Degree of Blistering of
Paints pressed Air
D1005 Test Method for Measurement of Dry-Film Thick- D4414 Practice for Measurement of Wet Film Thickness by
ness of Organic Coatings Using Micrometers
Notch Gages
D2240 Test Method for Rubber Property—Durometer Hard-
D4417 Test Methods for Field Measurement of Surface
ness
Profile of Blast Cleaned Steel
D2583 Test Method for Indentation Hardness of Rigid Plas-
D4537 Guide for Establishing Procedures to Qualify and
tics by Means of a Barcol Impressor
Certify Personnel Performing Coating and Lining Work
D3276 Guide for Painting Inspectors (Metal Substrates)
Inspection in Nuclear Facilities
D3359 Test Methods for Measuring Adhesion by Tape Test
D4538 Terminology Relating to Protective Coating and
D3363 Test Method for Film Hardness by Pencil Test
Lining Work for Power Generation Facilities
D4541 Test Method for Pull-Off Strength of Coatings Using
Portable Adhesion Testers
1
This guide is under the jurisdiction of ASTM Committee D33 on Protective
Coating and Lining Work for Power Generation Facilities and is the direct D4610 Guide for Determining the Presence of and Remov-
responsibility of Subcommittee D33.04 on Quality Systems and Inspection.
ing Microbial (Fungal or Algal) Growth on Paint and
Current edition approved March 1, 2012. Published March 2012. Originally
Related Coatings
approved in 1994. Last previous edition approved in 2009 as D5498 – 09. DOI:
10.1520/D5498-12. D4752 Practice for Measuring MEK Resistance of Ethyl
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Silicate (Inorganic) Zinc-Rich Primers by Solvent Rub
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
D4787 Practice for Continuity Verification of Liquid or
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. Sheet Linings Applied to Concrete Substrates
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D5498 − 12
D4940 Test Method for Conductimetric Analysis of Water SSPC-PA 10 Guide to Safety and Health Requirements for
Soluble Ionic Contamination of Blasting Abrasives Industrial Painting Projects
D5162 Practice for Discontinuity (Holiday) Testing of Non- SSPC-PA Guide 11 Protecting Edges, Crevices, and Irregu-
conductive Protective Coating on Metallic Substrates lar Steel Surfaced by Stripe Coating
D5163 Guide for Establishing a Program for Condition SSPC-SP1 Solvent Cleaning
...

This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:D5498–09 Designation:D5498–12
Standard Guide for
Developing a Training Program for Personnel Performing
1
Coating and Lining Work Inspection for Nuclear Facilities
This standard is issued under the fixed designation D5498; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (ϵ) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This guide is intended to assist those responsible for developing a program for the indoctrination and training of personnel
performing coating and lining inspection work for nuclear facilities.
1.2 It is recognized that organizations and job responsibilities vary widely among utilities and also among various support and
service companies. It is the responsibility of the user of this guide to identify the appropriate subject matter for its program and
its specific needs.
1.3 Users of this guide must ensure that coatingscoating and lining work complies not only with this guide, but also with the
licensee’s plant-specific quality assurance program and licensing commitments.
2. Referenced Documents
2
2.1 ASTM Standards:
D16 Terminology for Paint, Related Coatings, Materials, and Applications
D610 Practice for Evaluating Degree of Rusting on Painted Steel Surfaces
D714 Test Method for Evaluating Degree of Blistering of Paints
D1005 Test Method for Measurement of Dry-Film Thickness of Organic Coatings Using Micrometers
D2240 Test Method for Rubber PropertyDurometer Hardness
D2583 Test Method for Indentation Hardness of Rigid Plastics by Means of a Barcol Impressor
D3276 Guide for Painting Inspectors (Metal Substrates)
D3359 Test Methods for Measuring Adhesion by Tape Test
D3363 Test Method for Film Hardness by Pencil Test
D3843 Practice for Quality Assurance for Protective Coatings Applied to Nuclear Facilities
D3925 Practice for Sampling Liquid Paints and Related Pigmented Coatings
D4138 Practices for Measurement of Dry Film Thickness of Protective Coating Systems by Destructive, Cross-Sectioning
Means
D4212 Test Method for Viscosity by Dip-Type Viscosity Cups
D4214 Test Methods for Evaluating the Degree of Chalking of Exterior Paint Films
D4258 Practice for Surface Cleaning Concrete for Coating
D4259 Practice for Abrading Concrete
D4260 Practice for Liquid and Gelled Acid Etching of Concrete
D4261 Practice for Surface Cleaning Concrete Masonry Units for Coating
D4262 Test Method for pH of Chemically Cleaned or Etched Concrete Surfaces
D4263 Test Method for Indicating Moisture in Concrete by the Plastic Sheet Method
D4285 Test Method for Indicating Oil or Water in Compressed Air
D4414 Practice for Measurement of Wet Film Thickness by Notch Gages
D4417 Test Methods for Field Measurement of Surface Profile of Blast Cleaned Steel
D4537 Guide for Establishing Procedures to Qualify and Certify Personnel Performing Coating and Lining Work Inspection in
Nuclear Facilities
D4538
1
This guide is under the jurisdiction of ASTM Committee D33 on Protective Coating and Lining Work for Power Generation Facilities and is the direct responsibility
of Subcommittee D33.02D33.04 on Service Quality Systems and Material Parameters. Inspection.
Current edition approved JuneMarch 1, 2009.2012. Published July 2009.March 2012. Originally approved in 1994. Last previous edition approved in 20012009 as
D5498 – 019. DOI: 10.1520/D5498-09.10.1520/D5498-12.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
D5498–12
D4538 Terminology Relating to Protective Coating and Lining Work for Power Generation Facilities
D4541 Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers
D4610 Guide for Determining the Presence of and Removing Microbial (Fungal or Algal) Growth on Paint and Related
Coatings
D4752 Practice for Measuring MEK Resistance of Ethyl Silicate (Inorganic) Zinc-Rich Primers by Solvent Rub
D4787 Practice for Continuity Verification of Liquid or Sheet Linings Applied to Concrete Substrates
D4940 Test Method for Conductimetric Analysis of Water Soluble Ionic Contamination of Blasting A
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D8104-17(2023)(Guide)
Standard Guide for Determining Coating Qualification Test Data Applicability

SIGNIFICANCE AND USE
4.1 For conformance with the intent of the criteria listed in 2.2 and 2.3, coating qualification tests are founded on plant-specific test parameters that realistically reflect or bound the material and process variables that can reasonably be expected to influence qualification testing performance.  
4.2 This guide provides guidance for evaluating existing coating system qualification data for applicability to the nuclear plant desiring to use a coating system not previously used in the plant or to qualify an existing coating system.  
4.3 It is recognized that new-build plants, as well as small modular reactors currently under development, may have design features that differ from those of the operating plants that formed the basis for the existing test data. Therefore, careful review is required to assure that coating performance requirements critical to the new design are adequately addressed in the existing data or the need for additional coating testing is identified.
SCOPE
1.1 The purpose of this guide is to identify evaluation variables that can be used to determine whether existing coating qualification test data (for example, design basis accident or DBA, chemical resistance, fire resistance, thermal conductivity, etc.) meet the respective nuclear power plant qualification requirements or whether requalification is required. Guidance on developing a coating qualification test plan/procedure to qualify a new coating is beyond the scope of this standard.  
1.2 This guide is intended for use in new construction and for refurbishing existing coating systems applied to concrete and metal substrates within containment.  
1.3 This guide is intended for the use by, or under the supervision of, a person knowledgeable in coating technology and coatings used in CSL I applications, such as a person meeting the requirements of Guide D7108 or equivalent.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    6 pages
    English language
    sale 15% off
ASTM
ASTM D5163-16(2021)(Guide)
Standard Guide for Establishing a Program for Condition Assessment of Coating Service Level I Coating Systems in Nuclear Power Plants

SIGNIFICANCE AND USE
4.1 Establishment of an in-service coatings monitoring program permits planning and prioritization of coatings maintenance work as needed to maintain coating integrity and performance in nuclear CSL I coating systems. For additional information on nuclear maintenance coating work, refer to ASTM MNL8.4  
4.2 A coatings monitoring program enables early identification and detection of potential problems in coating systems. Some CSL I coating systems may be known in advance to be suspect, deficient, or unqualified. Monitoring coating performance will assist in developing follow-up procedures to resolve any significant deficiency relative to coating work.  
4.3 Degraded coatings may generate debris under design basis accident conditions that could adversely affect the performance of the post-accident safety systems. A coatings monitoring program may be required to fulfill safety analysis report and generic letter commitments for CSL I coating work in a nuclear power plant facility.
SCOPE
1.1 This standard covers procedures for establishing a monitoring program for condition assessment of Coating Service Level (CSL) I coating systems in operating nuclear power plants. Monitoring is an ongoing process of evaluating the condition and performance of the in-service coating systems.  
1.2 It is the intent of this standard to provide a recommended basis for establishing a coatings condition assessment program, not to mandate a singular basis for all programs. Variations or simplifications of the program described in this standard may be appropriate for each operating nuclear power plant depending on their licensing commitments.  
1.3 This requirements of ASME Section XI, In-Service Inspection Subsections IWE and IWL are beyond the scope of this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    5 pages
    English language
    sale 15% off
ASTM
ASTM D7491-21(Guide)
Standard Guide for Management of Non-Conforming Coatings in Coating Service Level I Areas of Nuclear Power Plants

SIGNIFICANCE AND USE
5.1 There are several methods for managing non-conforming coatings in an operating nuclear power plant. This guide outlines methods that have been determined to be acceptable to the nuclear industry.  
5.2 Managing the amount of non-conforming coatings is key to ensuring the amount assumed, in the licensing bases is not exceeded.  
5.3 EPRI Report 1019157 provides additional information on the selection, application, inspection and maintenance of nuclear plant safety-related protective coatings. This reference offers a detailed discussion of important considerations related to protective coatings and can be used to supplement this guide as deemed necessary.
SCOPE
1.1 This guide provides the user with guidance on developing a program for managing non-conforming coatings in Coating Service Level I areas of a nuclear power plant.  
1.2 Non-conforming coatings include degraded qualified or acceptable coatings, unqualified coatings, unknown coatings, and unacceptable coatings.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    4 pages
    English language
    sale 15% off
  • Guide
    4 pages
    English language
    sale 15% off
ASTM
ASTM D5139-19(Specification)
Standard Specification for Sample Preparation for Qualification Testing of Coatings to be Used in Nuclear Power Plants

ABSTRACT
This specification defines the size composition and surface preparation requirements for the preparation of test samples used for qualification testing of coatings utilized in nuclear power plant construction and maintenance. All panels should be carbon steel. Materials shall be tested for abrasion, and shall conform to specified requirements of steel samples, and concrete blocks.
SIGNIFICANCE AND USE
4.1 This specification provides uniform requirements for the preparation of test samples used for testing of coatings and linings to be used in nuclear power plants.  
4.2 At the users discretion, this standard may also be used when preparing samples to be tested for the purpose of assessing performance attributes for coating and lining systems that may be applied in other types of power plants or for other industrial facilities.  
4.3 Users of this guide must ensure that coatings work complies not only with this guide, but also with the licensee’s plant-specific quality assurance program and licensing commitments.
SCOPE
1.1 This specification defines the size, composition, surface preparation, and coating application variables for preparing samples for evaluating coatings and linings over various substrates.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM D7108-12(2018)(Guide)
Standard Guide for Establishing Qualifications for a Nuclear Coatings Specialist

SIGNIFICANCE AND USE
4.1 This guide applies to personnel technically responsible for the safety-related coatings program.  
4.2 It is the responsibility of each nuclear facility or organization participating in a safety-related coatings program to ensure that only those personnel within their respective organizations who meet the requirements of this guide are designated as Nuclear Coatings Specialists.
SCOPE
1.1 This guide delineates recommendations for development of procedures and criteria for designation of an individual as a Nuclear Coatings Specialist involved in coating work in nuclear facilities. The Nuclear Coatings Specialist is responsible for the technical aspects of the safety-related coatings program in a nuclear facility or organization, which includes establishing processes and quality control requirements.  
1.2 This guide details the guidance provided in Guide D5144, and EPRI Report 1019157.  
1.3 It is the intent of this guide to provide several alternatives for designation of personnel as Nuclear Coatings Specialists.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    3 pages
    English language
    sale 15% off
ASTM
ASTM D5498-12a(2018)(Guide)
Standard Guide for Developing a Training Program for Personnel Performing Coating and Lining Work Inspection for Nuclear Facilities

SIGNIFICANCE AND USE
4.1 Personnel trained for coating and lining work inspection are required to perform examination/inspection tasks to verify conformance of coating and lining work to written requirements.  
4.2 This guide provides guidance for development of an indoctrination and training program for training of personnel performing coating and lining work inspection.  
4.3 Certification/qualification of personnel performing coating and lining work inspection is addressed in Guide D4537.
SCOPE
1.1 This guide is intended to assist those responsible for developing a program for the indoctrination and training of personnel performing coating and lining inspection work for nuclear facilities.  
1.2 It is recognized that organizations and job responsibilities vary widely among utilities and also among various support and service companies. It is the responsibility of the user of this guide to identify the appropriate subject matter for its program and its specific needs.  
1.3 Users of this guide must ensure that coating and lining work complies not only with this guide, but also with the licensee's plant-specific quality assurance program and licensing commitments.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    4 pages
    English language
    sale 15% off
ASTM
ASTM D7167-12(2018)(Guide)
Standard Guide for Establishing Procedures to Monitor the Performance of Safety-Related Coating Service Level III Lining Systems in an Operating Nuclear Power Plant

SIGNIFICANCE AND USE
4.1 Establishment of an in-service linings monitoring program permits planning and prioritization of lining maintenance work as needed to maintain lining integrity and performance in nuclear Coating Service Level III systems. Refer to ASTM MNL-8, Manual on Maintenance Coatings for Nuclear Power Plants,7 and Guide D7230, which provides guidance for selecting lining materials for new construction or maintenance of safety-related lining systems.  
4.2 A linings monitoring program enables early identification and detection of potential problems in lining systems. Some Coating Service Level III lining systems may be known in advance to be suspect, deficient, or degraded. Monitoring lining performance will assist in developing follow-up procedures to resolve any significant deficiency relative to lining work.  
4.3 Degraded linings may generate debris under normal operation and testing or during upset conditions that could adversely affect the performance of safety-related systems. In most cases, the consequence of the debris generation is flow blockage, essential heat transfer reduction, or both; ultimately leading to degradation of equipment or system performance. A linings monitoring program may be required to fulfill licensing commitments for Coating Service Level III lining work.
SCOPE
1.1 This guide covers procedures for establishing a program to monitor the performance of Coating Service Level III lining (and coating) systems in operating nuclear power plants. Monitoring is an ongoing process of evaluating the condition of the in-service lining systems.  
1.2 Coating Service Level III lining systems subject to this guide are generally those applied to metal substrates comprising raw water, condensate-quality water, or fuel oil wetted (that is, full or intermittent immersion) surfaces in systems that may include:  
1.2.1 Service water piping upstream of safety-related components,  
1.2.2 Service water pump internals (draft tube, volutes, and diffusers),  
1.2.3 Service water heat exchangers including the channels, pass partitions, tubesheets, end bells, and covers  
1.2.4 Service water strainers,  
1.2.5 Reactor water storage tanks (RWSTs),  
1.2.6 Refuel cavity water storage tanks,  
1.2.7 Reactor makeup water system,  
1.2.8 Component cooling water system,  
1.2.9 Lube oil tanks for safety-related equipment, and  
1.2.10 Emergency diesel fuel oil system.  
1.3 It is the intent of this guide to provide a recommended basis for establishing a linings monitoring program, not to mandate a singular basis for all programs. Variations or simplifications of the program described in this guide may be appropriate for any given operating nuclear power plant depending on its licensing commitments. Similar guidelines may be applicable for certain Coating Service Level II applications such as fluid immersion systems.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    6 pages
    English language
    sale 15% off
ASTM
ASTM E853-23(Practice)
Standard Practice for Analysis and Interpretation of Light-Water Reactor Surveillance Neutron Exposure Results

SIGNIFICANCE AND USE
3.1 The objectives of a reactor vessel surveillance program are twofold. The first requirement of the program is to monitor changes in the fracture toughness properties of ferritic materials in the reactor vessel beltline region resulting from exposure to neutron irradiation and the thermal environment. The second requirement is to make use of the data obtained from the surveillance program to determine the conditions under which the vessel can be operated throughout its service life.  
3.1.1 To satisfy the first requirement of 3.1, the tasks to be carried out are straightforward. Each of the irradiation capsules that comprise the surveillance program may be treated as a separate experiment. The goal is to define and carry to completion a dosimetry program that will, a posteriori, describe the neutron field to which the material test specimens were exposed. The resultant information will then become part of a database applicable in a stricter sense to the specific plant from which the capsule was removed, but also in a broader sense to the industry as a whole.  
3.1.2 To satisfy the second requirement of 3.1, the tasks to be carried out are somewhat complex. The objective is to describe accurately the neutron field to which the pressure vessel itself will be exposed over its service life. This description of the neutron field must include spatial gradients within the vessel wall. Therefore, heavy emphasis must be placed on the use of neutron transport techniques as well as on the choice of a design basis for the computations. Since a given surveillance capsule measurement, particularly one obtained early in plant life, is not necessarily representative of long-term reactor operation, a simple normalization of neutron transport calculations to dosimetry data from a given capsule may not be appropriate (1-67).  
3.2 The objectives and requirements of a reactor vessel's support structure's surveillance program are much less stringent, and at present, are limited to ...
SCOPE
1.1 This practice covers the methodology, summarized in Annex A1, to be used in the analysis and interpretation of neutron exposure data obtained from LWR pressure vessel surveillance programs and, based on the results of that analysis, establishes a formalism to be used to evaluate present and future condition of the pressure vessel and its support structures2 (1-74).3  
1.2 This practice relies on, and ties together, the application of several supporting ASTM standard practices, guides, and methods (see Master Matrix E706) (1, 5, 13, 48, 49).2 In order to make this practice at least partially self-contained, a moderate amount of discussion is provided in areas relating to ASTM and other documents. Support subject areas that are discussed include reactor physics calculations, dosimeter selection and analysis, and exposure units.  
1.3 This practice is restricted to direct applications related to surveillance programs that are established in support of the operation, licensing, and regulation of LWR nuclear power plants. Procedures and data related to the analysis, interpretation, and application of test reactor results are addressed in Practice E1006, Guide E900, and Practice E1035.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    9 pages
    English language
    sale 15% off
  • Standard
    9 pages
    English language
    sale 15% off
ASTM
ASTM E3104-17(2023)(Specification)
Standard Specification for Strippable and Removable Coatings to Mitigate Spread of Radioactive Contamination

ABSTRACT
This specification prescribes the performance criteria for strippable/removable coatings used in immobilizing radioactive contamination, minimizing worker exposure, and facilitating subsequent decontamination or protecting uncontaminated areas against the spread of radioactive contamination. It covers the minimum performance requirements (shelf life, tensile strength, adhesion, abrasion resistance, dry/cure time, decontamination factor, airborne release fraction) as well as the mechanical and chemical properties for strippable/removable coatings. The strippable/removable coating is intended to reduce: migration of the radioactive contamination into or along buildings, equipment, and other surfaces; resuspension of contamination into the air and the airborne intake hazards of the contamination; and the spread of contamination as a result of external forces such as pedestrian traffic. The strippable/removable coating shall: be applicable to both vertical and horizontal surfaces; work within a range of environmental and radiological conditions; and be readily applied to both porous and nonporous materials such as concrete, wood, metal, ceramics, and plastics. Furthermore, the strippable/removable coating may include constituents that will physically or chemically bind and immobilize radioactive contamination.
SCOPE
1.1 This specification is intended to provide a basis for identification of strippable/removable materials used to immobilize radioactive contamination, minimize worker exposure, and facilitate subsequent decontamination or to protect uncontaminated areas against the spread of radioactive contamination.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM E3105-17(2023)(Specification)
Standard Specification for Permanent Coatings Used to Mitigate Spread of Radioactive Contamination

ABSTRACT
This specification prescribes the performance criteria for non-removable permanent coatings and fixatives as a long-term measure used to immobilize radioactive contamination, minimize worker exposure, and protect uncontaminated areas against the spread of radioactive contamination. It covers the minimum performance requirements (shelf life, adhesion, abrasion resistance, dry/cure time, decontamination factor, airborne release fraction, respirable fraction, radiation resistance) as well as the mechanical and chemical properties for permanent coatings that are intended to immobilize dispersible radioactive contamination deposited on buildings and equipment as might result from anticipated to unanticipated events to include normal operating conditions, decommissioning, and radiological release. The coating is intended to reduce: migration of the contamination into or along buildings, equipment, and other surfaces; resuspension of contamination into the air; and the spread of contamination as a result of external forces such as pedestrian traffic. It shall: be applicable to both vertical and horizontal surfaces; work within a range of environmental and radiological conditions; and be applicable to both porous and nonporous materials such as concrete, wood, metal, ceramics, and plastics. Furthermore, the coating may include constituents that will physically or chemically bind and hold radioactive contamination.
SCOPE
1.1 This specification is intended to provide a basis for identification of non-removable permanent coatings and fixatives as a long-term measure used to immobilize radioactive contamination, minimize worker exposure, and to protect uncontaminated areas against the spread of radioactive contamination.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off