ASTM C847-10a
(Specification)Standard Specification for Metal Lath
Standard Specification for Metal Lath
ABSTRACT
This specification covers sheet lath, expanded metal lath, diamond mesh, flat and self-furring, and rib metal lath, all with or without backing and designed to be used as a base for gypsum or Portland cement plaster. Metal lath shall be fabricated from cold-rolled carbon steel sheet of commercial quality as specified and galvanized metal lath shall have a G60 coating. Physical properties such as thickness, width, length, and weight shall be specified. Metal lath shall be fabricated from hot-dipped galvanized steel.
SCOPE
1.1 This astmspecification covers sheet lath, expanded metal lath, diamond mesh, flat and self-furring, and rib metal lath, 1/8 and 3/8 in. (3.2 and 9.6 mm), all with or without backing and designed to be used as a base for gypsum or portland cement plaster.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: C847 – 10a
Standard Specification for
1
Metal Lath
This standard is issued under the fixed designation C847; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope* (9.6mm).Thenominalthicknessofself-furringdiamondmesh
5
shall be ⁄16 in. (7.9 mm).
1.1 This specification covers sheet lath, expanded metal
1 4.2 Width—Theminimumwidthofmetallathshallbe27in.
lath, diamond mesh, flat and self-furring, and rib metal lath, ⁄8
(686 mm).
3
and ⁄8 in. (3.2 and 9.6 mm), all with or without backing and
4.3 Length—The minimum length of metal lath shall be 97
designed to be used as a base for gypsum or portland cement
in. (2464 mm).
plaster.
4.4 Weight—The nominal weight of metal lath shall be as
1.2 The values stated in inch-pound units are to be regarded
follows:
as standard. The values given in parentheses are mathematical
4.4.1 U.S. Nominal Weights:
conversions to SI units that are provided for information only
and are not considered standard.
2 2
Type: Weight, lb/yd (kg/m )
2. Referenced Documents
Diamond mesh 2.5 (1.4); 3.4 (1.8)
2
2.1 ASTM Standards:
Flat rib 1.8 (1.0); 2.75 (1.5); 3.4 (1.8)
3
⁄8-in. rib 3.4 (1.8); 4.0 (2.1)
A653/A653M Specification for Steel Sheet, Zinc-Coated
(Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed)
4.4.2 Canadian Nominal Weights:
by the Hot-Dip Process
2 2
Type: Weight, lb/yd (kg/m )
3. Material
Diamond mesh 2.5 (1.4); 3.0 (1.6); 3.4 (1.8)
3.1 Metal lath shall be fabricated from cold-rolled carbon
Flat rib 1.8 (1.0); 2.5 (1.4); 3.0 (1.6)
steel sheet of commercial quality conforming to Specification
3
⁄8-in. rib 3.0 (1.6); 3.5 (1.9); 4.0 (2.1)
A653/A653M. Galvanized metal lath shall have a G60 coating
4.5 Permissible Variations—The permissible variations
in accordance with Specification A653/A653M.
shall be as follows:
3.2 Backing shall be attached to the lath sufficiently enough
1
4.5.1 Thickness, 6 ⁄64 in. (0.4 mm).
to prevent accidental removal during shipping, handling, or
3
4.5.2 Width, 6 ⁄8 in. (9.5 mm).
installation.Attachment of backing shall also allow lapping of
1
4.5.3 Length,−0in.,+1 ⁄2 in. (38.1 mm).
metal to metal and backing to backing, 1 in. (25.4 mm) on the
4.5.4 Weight, 6 10%.
1
ends and ⁄2 in. (12.7 mm) on the sides.
5. Finish
4. Dimensions, Mass, and Permissible Variations
5.1 Metal lath shall be fabricated from hot-dipped galva-
4.1 Thickness—The nominal thickness of diamond mesh
nized steel.
1
and flat rib metal lath shall be ⁄8 in. (3.2 mm). The nominal
3
thickness of other rib metal lath shall be as designated, ⁄8 in.
6. Weight Test
6.1 Significance and Use—This test method provides a
1
This specification is under the jurisdiction of ASTM Committee C11 on
procedure for measuring the weight of a single sheet of metal
GypsumandRelatedBuildingMaterialsandSystemsandisthedirectresponsibility
lath. It shall be used to determine compliance with this
of Subcommittee C11.02 on Specifications and Test Methods for Accessories and
specification. The degree of performance of this test method
Related Products.
Current edition approved Oct. 1, 2010. Published November 2010. Originally with service performance has not been determined.
approved in 1977. Last previous edition approved in 2010 as C847–10. DOI:
6.2 Apparatus:
10.1520/C0847-10a.
6.2.1 Scale, capable of weighing in increments of 0.1 lb
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
(0.05 kg) or 1 oz (28 g).
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
C847 – 10a
6.2.2 Tape Measure, capable of measuring in increments of 6.7.3 Ifmorethanoneofthetestspecimensfails,thesample
1
⁄16 in (1.6 mm). has failed to meet the requirements of the test.
6.3 Materials shall satisfy the following: 6.8 Report—Reportshallindicatethetotalnumberofspeci-
6.3.1 Metal Lath—Specification C847. mens tested and the number of specimens meeting the require-
6.4 Sampling—One sheet shall be selected from each ments of this specification.
bundle or package, but not more than five sheets from any one 6.9 Precision and Bias—No statement is made about either
shipment for testing. the precision or bias of this test method since the result merely
6.5 Specimen Preparation: sta
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:C847–10 Designation: C847 – 10a
Standard Specification for
1
Metal Lath
This standard is issued under the fixed designation C847; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope*
1
1.1 Thisastmspecificationcoverssheetlath,expandedmetallath,diamondmesh,flatandself-furring,andribmetallath, ⁄8and
3
⁄8 in. (3.2 and 9.6 mm), all with or without backing and designed to be used as a base for gypsum or portland cement plaster.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
2. Referenced Documents
2
2.1 ASTM Standards:
A653/A653M Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the
Hot-Dip Process
3. Material
3.1 Metal lath shall be fabricated from cold-rolled carbon steel sheet of commercial quality conforming to Specification
A653/A653M. Galvanized metal lath shall have a G60 coating in accordance with Specification A653/A653M.
3.2 Backing shall be attached to the lath sufficiently enough to prevent accidental removal during shipping, handling, or
installation.Attachment of backing shall also allow lapping of metal to metal and backing to backing, 1 in. (25.4 mm) on the ends
1
and ⁄2 in. (12.7 mm) on the sides.
4. Dimensions, Mass, and Permissible Variations
1
4.1 Thickness—The nominal thickness of diamond mesh and flat rib metal lath shall be ⁄8 in. (3.2 mm).The nominal thickness
3 5
of other rib metal lath shall be as designated, ⁄8 in. (9.6 mm). The nominal thickness of self-furring diamond mesh shall be ⁄16
in. (7.9 mm).
4.2 Width—The minimum width of metal lath shall be 27 in. (686 mm).
4.3 Length—The minimum length of metal lath shall be 97 in. (2464 mm).
4.4 Weight—The nominal weight of metal lath shall be as follows:
4.4.1 U.S. Nominal Weights:
2 2
Type: Weight, lb/yd (kg/m )
Diamond mesh 2.5 (1.4); 3.4 (1.8)
Flat rib 1.8 (1.0); 2.75 (1.5); 3.4 (1.8)
3
⁄8-in. rib 3.4 (1.8); 4.0 (2.1)
4.4.2 Canadian Nominal Weights:
2 2
Type: Weight, lb/yd (kg/m )
Diamond mesh 2.5 (1.4); 3.0 (1.6); 3.4 (1.8)
Flat rib 1.8 (1.0); 2.5 (1.4); 3.0 (1.6)
3
⁄8-in. rib 3.0 (1.6); 3.5 (1.9); 4.0 (2.1)
4.5 Permissible Variations—The permissible variations shall be as follows:
1
This specification is under the jurisdiction of ASTM Committee C11 on Gypsum and Related Building Materials and Systems and is the direct responsibility of
Subcommittee C11.02 on Specifications and Test Methods for Accessories and Related Products.
Current edition approved MayOct. 1, 2010. Published JuneNovember 2010. Originally approved in 1977. Last previous edition approved in 20092010 as
C847–09.C847–10. DOI: 10.1520/C0847-10a.
2
ForreferencedASTMstandards,visittheASTMwebsite,www.astm.org,orcontactASTMCustomerServiceatservice@astm.org.For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
C847 – 10a
1
4.5.1 Thickness, 6 ⁄64 in. (0.4 mm).
3
4.5.2 Width, 6 ⁄8 in. (9.5 mm).
1
4.5.3 Length,−0in.,+1 ⁄2 in. (25.4(38.1 mm).
4.5.4 Weight, 6 10%.
5. Finish
5.1 Metal lath shall be fabricated from hot-dipped galvanized steel.
6. Weight Test
6.1 Significance and Use—This test method provides a procedure for measuring the weight of a single sheet of metal lath. It
shall be used to determine compliance with this specification. The degree of performance of this test method with service
performance has not been determined.
6.2 Apparatus:
6.2.1 Scale, capable of weighing in increments of 0.1 lb (0.05 kg) or 1 oz (28 g).
1
6.2.2 Tape Measure, capable of measuring in increments of ⁄16 in (1.6 mm).
6.3 Materials shall satisfy the following:
6.3.1 Metal Lath—Specification C847.
6.4 Sampling—One sheet shall be selected from each bundle or package, but not more than five sheets from any one shipment
for testing.
6.5 Specimen Preparation:
6.5.1 Measure and record the width and length of each
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.