iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D4907-10(2020)

(Test Method)

Standard Test Method for Nitrocellulose in Finish on Leather

Standard Test Method for Nitrocellulose in Finish on Leather

SIGNIFICANCE AND USE
2.1 This test method is used to identify nitrocellulose in finishes on all types of leathers.
SCOPE
1.1 This test method is intended for use in identifying nitrocellulose in the finish on all types of leathers. This test method does not apply to wet blue.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

Status
Published
Publication Date
31-Mar-2020
ICS
59.140.10 - Processes and auxiliary materials
Technical Committee
D31 - Leather
Drafting Committee
D31.06 - Chemical Analysis
Current Stage
Ref Project

Relations

Replaces
ASTM D4907-10(2015) - Standard Test Method for Nitrocellulose in Finish on Leather
Effective Date
01-Apr-2020

Buy Standard

ASTM D4907-10(2020) - Standard Test Method for Nitrocellulose in Finish on LeatherASTM D4907-10(2020) - Standard Test Method for Nitrocellulose in Finish on Leather
PreviousNext
Standard
ASTM D4907-10(2020) - Standard Test Method for Nitrocellulose in Finish on Leather
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: D4907 − 10 (Reapproved 2020)
Standard Test Method for
Nitrocellulose in Finish on Leather
This standard is issued under the fixed designation D4907; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 4.4 Hazards Statement—All reagents and chemicals should
be handled with care. Before using any chemical, read and
1.1 This test method is intended for use in identifying
follow all safety precautions and instructions on the manufac-
nitrocellulose in the finish on all types of leathers. This test
turer’s label or MSDS (Material Safety Data Sheet).
method does not apply to wet blue.
5. Test Specimen
1.2 The values stated in SI units are to be regarded as
standard. No other units of measurement are included in this
5.1 The test specimen shall be approximately 1 cm of the
standard.
finished leather.
1.3 This standard does not purport to address all of the
6. Procedure
safety concerns, if any, associated with its use. It is the
6.1 Place the test specimen in the watch glass with the finish
responsibility of the user of this standard to establish appro-
side up. Apply one or 2 mL of indicator solution on the finish
priate safety, health, and environmental practices and deter-
and allow to run over the side of the leather on to the watch
mine the applicability of regulatory limitations prior to use.
glass. After 3 min, if the indicator solution does not develop a
1.4 This international standard was developed in accor-
dark blue color, then nitrocellulose is not present in the finish.
dance with internationally recognized principles on standard-
If the indicator solution develops a dark blue color after contact
ization established in the Decision on Principles for the
with the finish, it indicates the presence of nitrocellulose or has
Development of International Standards, Guides and Recom-
developed color from colored finish components, or both.
mendations issued by the World Trade Organization Technical
Barriers to Trade (TBT) Committee.
6.2 Repeat the above procedure except that the blank
solution is employed instead of the indicator solution. If a dark
2. Significance and Use
blue color does not develop, whereas it does when the indicator
2.1 This test method is used to identify nitrocellulose in
solution is applied, then nitrocellulose is present in the finish
finishes on all types of leathers.
and colored finishing materials do not interfere.
6.3 If colored finish material develops a dark blue color in
3. Apparatus
the presence of the blank solution, then place the specimen
3.1 Borosilicate Glass Watch Glass, 100 mm diameter.
finish side up in a watch glass and pour acetone on the
3.2 Reagent Bottles, two, (4 fl oz each) equipped with glass
specimen, until completely covered, for dissolving any nitro-
joint dropping pipet. cellulose present in the specimen.After allowing the specimen
to soak in acetone for approximately 2 min, remove the
4. Reagents
specimen from the watch glass and the evaporate acetone in the
4.1 Indicator solution prepared by d
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D3898-93(2023)(Test Method)
Standard Test Method for Chromic Oxide in Basic Chromium Tanning Liquors

SIGNIFICANCE AND USE
4.1 The procedure described is for the quality control for manufacturing liquors and specifications for the purchase of such liquors.  
4.2 The chromium content of the liquors determines the amount to be used to obtain the desired degree of tannage, and hence may be a matter for specification in the purchase of leather.
SCOPE
1.1 This test method covers the determination of chromic oxide in chrome tanning liquors, either simple, with added aluminum or zirconium, or with the usual masking complexing agents.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D6182-23(Test Method)
Standard Test Method for Flexibility and Adhesion of Finish on Leather

SIGNIFICANCE AND USE
5.1 This test method is intended for use on any type of finished leather.  
5.2 This test method will give an indication of the flexibility, adhesion, and strength of the finish on leather.
SCOPE
1.1 This test method is intended for use on finished leather to evaluate resistance to cracking, delamination, and discoloration of the finish when subjected to repeated flexing. This test method does not apply to wet blue.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D4906-95(2023)(Test Method)
Standard Test Method for Total Solids and Ash Content in Leather Finishing Materials

SIGNIFICANCE AND USE
2.1 This test method is intended for use in determining the total solids content and the ash content of a finishing material before its use on any leather.
SCOPE
1.1 This test method covers the total solids and ash content of finishing materials.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D6183-00(2021)(Test Method)
Standard Test Method for Tackiness of Finish on Leather

SIGNIFICANCE AND USE
5.1 This test method is intended for use on any type of finished leather.  
5.2 This test will give an indication of the tackiness of the finish on leather.
SCOPE
1.1 This test method is intended for use on finished leather to evaluate the tendency of cloth to adhere to it. This test method does not apply to wet blue.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D6659-16(2021)(Practice)
Standard Practice for Sampling and Preparation of Wet Blue and Wet White for Physical and Chemical Tests

SIGNIFICANCE AND USE
4.1 The sampling procedures described in this practice have been designed to ensure random sampling of Wet Blue and Wet White for physical and chemical tests. Wet Blue and Wet White are natural products and as such are subject to extensive variability. The physical and chemical properties vary considerably depending on location on the hide, side, or skin from which the test sample is taken. Random sampling of specimens from a predefined location and orientation minimizes test bias and variability. This practice defines these parameters.
SCOPE
1.1 This practice covers the sampling and preparation of Wet Blue and Wet White for physical and chemical tests. The product is grouped into lots that are randomly sampled in such a manner as to produce a representative sample of the lot. This sample may be used to determine compliance of the lot with applicable specification requirements, and on the basis of results, the lot may be accepted or rejected in its entirety.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D6656-16(2021)(Test Method)
Standard Test Method for Determination of Chromic Oxide in Wet Blue (Perchloric Acid Oxidation)

SIGNIFICANCE AND USE
5.1 The procedure described is specific for chromium in Wet Blue. Vanadium is the only common interfering element and is rarely present in quantity. The precision and accuracy of the methods are usually, at least, as good as the sampling of Wet Blue itself.  
5.2 The chromium content of Wet Blue is related to the degree of tannage obtained, and hence may be a matter for specification in the purchase of Wet Blue. The procedure described provides adequate accuracy for this purpose.
SCOPE
1.1 This test method covers the determination of chromic oxide in Wet Blue that has been partly or completely tanned with chromium compounds. In general, the samples will contain chromium content between 1 % and 5 % when calculated as chromic oxide expressed upon a dry basis otherwise referred to as moisture-free basis (mfb).  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This test method does not apply to Wet White.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. See Section 9 for specific safety hazards.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM D6657-16(2021)(Test Method)
Standard Test Method for pH of Wet Blue and Wet White

SIGNIFICANCE AND USE
4.1 This test method is designed to measure the pH of a distilled-water extract of Wet Blue and Wet White. This is considered to be a measure of the acidity or alkalinity of the Wet Blue or Wet White. Excessive acidity or alkalinity may have a deleterious effect on the aging characteristics of Wet Blue and Wet White and the leather made from it.  
4.2 This test method is suitable for development, control, and service evaluation of wet blue.
SCOPE
1.1 This test method covers the determination of the pH of all types of Wet Blue and Wet White.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D6402-99(2020)(Test Method)
Standard Test Method for Determining Soluble Solids and Insolubles in Extracts of Vegetable Tanning Materials

SIGNIFICANCE AND USE
5.1 This test method is used to determine the proportion of the total solids which are soluble solids and that proportion which are insoluble solids in a solution of tannin extract or in the water extract from raw or spent materials prepared for tannin analysis.  
5.2 The specimens are aliquots from the analytical solutions prepared from tannin extracts or the water extract solutions prepared from raw or spent materials.  
5.3 The soluble solids are defined as the portion of the total solids which are dissolved in the water and pass through a filter prepared by depositing a layer of Kaolin paste onto a standard filter paper.  
5.4 The insolubles are defined as the portion of the total solids which do not pass through the standard filter paper prepared with the layer of Kaolin paste.  
5.5 The results of this test method are dependent on a great many variables but particularly upon:  
5.5.1 The temperature conditions under which the solutions were prepared and stored and the temperature at which the current analysis is performed;  
5.5.2 The uniformity and consistency of the Kaolin paste layer deposited onto the filter paper;  
5.5.3 The rate of solution run-out from the pipette; etc. It is, therefore, essential that the method be followed exactly in order to obtain reproducible results both among specimens within a laboratory and for analyses between laboratories.
SCOPE
1.1 This test method is intended for use in determining the quantity of soluble solids and insolubles in solutions of tannin extracts, water extracts of vegetable tanning materials, or tanning liquors. This test method is applicable to the analysis of liquid, solid, pasty, and powdered tannin extracts and to the water extracts of raw or spent materials.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D6409-99(2020)(Practice)
Standard Practice for Color Tests with Sheepskin Skiver

SIGNIFICANCE AND USE
5.1 This practice provides a standard procedure for comparing the color of leather tanned with different tanning extracts or mixtures of extracts or for monitoring the color consistency of tannery liquors.
SCOPE
1.1 This practice covers making color tests of all types of vegetable tanning extracts and of vegetable tanning materials to determine the color imparted to tanned skins.  
1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D4901-99(2020)(Practice)
Standard Practice for Preparation of Solution of Liquid Vegetable Tannin Extracts

SIGNIFICANCE AND USE
4.1 The concentration of tannin in extracts must be reduced to analytical strength (4 g tannin per L) for analysis.  
4.2 Vegetable tannin extracts are heterogeneous mixtures of components with varying solubility.  
4.3 The solubility of such extracts is influenced by temperature and concentration, which affect the degree of dispersion and size of the component particles.  
4.4 While the solubility is better in hot water than in cold water, it is appropriate to dissolve and disperse an extract in hot water and then let the solution cool slowly to standard room temperature.
SCOPE
1.1 This practice covers the preparation of a solution of liquid extract that is to be used in the tannin analysis of that extract.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off