ASTM F2200-13e1
(Specification)Standard Specification for Automated Vehicular Gate Construction
Standard Specification for Automated Vehicular Gate Construction
ABSTRACT
This specification establishes the performance-based and prescriptive-based methods of evaluating various classes of automated gate constructions that are used for vehicular traffic. The gate types addressed in this specification include horizontal slide gates, horizontal swing gates, vertical lift gates, vertical pivot gates, and overhead pivot gates. Conversely, the four classes of gates covered here are as follows: Class I, a gate for the garage or parking area intended for use in a home of a one-to-four single family dwelling; Class II, a gate intended for use in a commercial location or building such as a multi-family housing unit (five or more single family units), hotel, garages, retail store, or other building servicing the general public; Class III, a gate intended for use in an industrial location or building such as a factory, loading dock area, or other locations not intended to service the general public; and Class IV, a gate intended for use in a guarded industrial location or building such as an airport security area, or other restricted access locations not servicing the general public, in which unauthorized access is prevented by means of supervision by security personnel.
SCOPE
1.1 This specification defines performance-based and prescriptive-based methods of evaluating various classes of gates that are used for vehicular traffic and are to be automated.
1.2 Gate types addressed in this specification include horizontal slide gates, horizontal swing gates, vertical lift gates, vertical pivot gates and overhead pivot gates.
1.3 Gate types not listed in this specification will be subject to any applicable provisions contained in this specification.
1.4 Automated vehicular gates that do not comply with this specification shall be subject to independent evaluation for compliance with UL 325.
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
´1
Designation:F2200 −13
StandardSpecification for
1
Automated Vehicular Gate Construction
This standard is issued under the fixed designation F2200; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1
ε NOTE—Sections 3.3 through 3.6 were corrected editorially in March 2014.
1. Scope 3.4 Class II Gate—a gate intended for use in a commercial
locationorbuildingsuchasamulti-familyhousingunit(fiveor
1.1 This specification defines performance-based and
more single family units), hotel, garages, retail store, or other
prescriptive-based methods of evaluating various classes of
building accessible by or servicing the general public.
gates that are used for vehicular traffic and are to be automated.
3.5 Class III Gate—a gate intended for use in an industrial
1.2 Gate types addressed in this specification include hori-
location or building such as a factory or loading dock area or
zontal slide gates, horizontal swing gates, vertical lift gates,
other locations not accessible by or intended to service the
vertical pivot gates and overhead pivot gates.
general public.
1.3 Gate types not listed in this specification will be subject
3.6 Class IV Gate—a gate intended for use in a guarded
to any applicable provisions contained in this specification.
industrial location or building such as a airport security area or
1.4 Automated vehicular gates that do not comply with this
other restricted access locations not servicing the general
specification shall be subject to independent evaluation for public, in which unauthorized access is prevented via supervi-
compliance with UL 325.
sion by security personnel.
3.7 entrapment—the condition of being caught or held in a
1.5 The values stated in inch-pound units are to be regarded
position that increases the risk of injury.
as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only
3.8 gatelatch—amanualmechanismthatsecuresthegatein
and are not considered standard.
either the fully closed or fully open position.
3.9 gate lock—an electro-mechanical mechanism that locks
2. Referenced Documents
the gate in either the fully closed or fully open position.
2.1 UL Standard:
3.10 positive stop—a physical device that limits gate travel.
UL 325 Standard for Door, Drapery, Gate, Louver, and 2
3.11 protrusion—an object less than 9 in. (5806 mm) of
2
Window Operators and Systems
cross sectional area and permanently attached to the gate with
asurfacethatextendsbeyondtheextremehorizontalorvertical
3. Terminology
planes created by the gate structure members.
3.1 bottom retainer—an angle or lip attached to the bottom
3.12 receiver post—a post to which a receiver guide is
horizontal member of a slide gate, usually used on a gate
attached.
installed in a high security-related application, intended to
3.13 receiver guide—a device mounted to a post or other
protect a gate from crash-through related damage from vehicu-
fixed object which provides lateral stability to a closed gate.
lar impact.
3.14 vehicular horizontal slide gate—a gate that slides in a
3.2 catcher—see receiver guide.
horizontal direction and is intended for use at a vehicular
3.3 Class I Gate—a gate intended for use in garages or
entrance or exit to a drive, parking lot, or the like.
parking areas associated with a residence of one to four single
3.15 vehicular horizontal swing gate—a gate that swings in
families.
a horizontal arc in a horizontal plane and is intended for use at
a vehicular entrance or exit to a drive, parking lot, or the like.
3.16 vehicular overhead pivot gate—a gate made in one
1
This specification is under the jurisdiction ofASTM Committee F14 on Fences
rigid piece designed to close an entire opening at a vehicular
and is the direct responsibility of Subcommittee F14.10 on Specific Applications.
Current edition approved July 1, 2013. Published July 2013. Originally approved
entrance or exit to a drive, parking lot, or the like, where
in 2002. Last previous edition approved in 2011 as F2200 - 11b. DOI: 10.1520/
openingandclosingisaccomplishedbypivotingthegateabout
F2200-13E01.
2
an axis, with or without a horizontal track to guide the top of
Available from Underwriters Laboratories (UL), 333 Pfingsten Rd.,
Northbrook, IL 60062-2096, http://www.ul.com. the gate.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
´1
F2200−13
3.17 vehicular vertical lift gate—a gate that moves in the 4.9 Gates shall be designed, constructed and installed
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.