iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM F1860-10

(Specification)

Standard Specification for Rubber Sheet Floor Covering With Backing

Standard Specification for Rubber Sheet Floor Covering With Backing

ABSTRACT
This specification covers the requirements for the compound and physical characteristics of homogeneous (Type I) and layered (Type II) rubber sheet floor covering with backing. Both types shall be fibrous and foamed rubber, and may also contain intermediate layers. They may either have smooth, embossed, or molded pattern surfaces, and shall not contain asbestos. They shall be tested on, and conform accordingly to the following requirements: chemical composition; hardness; modulus of 10 % elongation; static load limit; resistance to chemicals such as white vinegar, rubbing alcohol, sodium hydroxide solution, hydrochloric acid solution, sulfuric acid solution, household ammonia solution, and household bleach; resistance to heat; resistance to light; width and length; and base, wear layer, and overall thicknesses.
SCOPE
1.1 This specification covers the requirements for the compound and physical characteristics of rubber sheet floor covering having a rubber wear layer with backing. Products may also contain intermediate layers.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 The following precautionary statement pertains only to the test method portion, Section 10, of this specification:  This standard does not purport to address all the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
30-Apr-2010
ICS
97.150 - Floor coverings
Technical Committee
F06 - Resilient Floor Coverings
Drafting Committee
F06.80 - Specifications
Current Stage
Ref Project

Relations

Replaces
ASTM F1860-04(2009)e1 - Standard Specification for Rubber Sheet Floor Covering With Backing
Effective Date
01-May-2010
Replaced By
ASTM F1860-12 - Standard Specification for Rubber Sheet Floor Covering With Backing
Effective Date
01-May-2012
Referred By
ASTM F141-12(2020) - Standard Terminology Relating to Resilient Floor Coverings
Effective Date
01-May-2010

Buy Standard

ASTM F1860-10 - Standard Specification for Rubber Sheet Floor Covering With BackingASTM F1860-10 - Standard Specification for Rubber Sheet Floor Covering With Backing
PreviousNext
Technical specification
ASTM F1860-10 - Standard Specification for Rubber Sheet Floor Covering With Backing
English language
4 pages
sale 15% off
Preview
sale 15% off
Preview
REDLINE ASTM F1860-10 - Standard Specification for Rubber Sheet Floor Covering With BackingREDLINE ASTM F1860-10 - Standard Specification for Rubber Sheet Floor Covering With Backing
PreviousNext
Technical specification
REDLINE ASTM F1860-10 - Standard Specification for Rubber Sheet Floor Covering With Backing
English language
4 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Please contact ASTM International (www.astm.org) for the latest information.
Designation: F1860 – 10
Standard Specification for
1
Rubber Sheet Floor Covering With Backing
This standard is issued under the fixed designation F1860; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope F925 Test Method for Resistance to Chemicals of Resilient
Flooring
1.1 This specification covers the requirements for the com-
F970 Test Method for Static Load Limit
pound and physical characteristics of rubber sheet floor cov-
F1482 Practice for Installation and Preparation of Panel
ering having a rubber wear layer with backing. Products may
Type Underlayments to Receive Resilient Flooring
also contain intermediate layers.
F1514 Test Method for Measuring Heat Stability of Resil-
1.2 The values stated in inch-pound units are to be regarded
ient Flooring by Color Change
as standard. The values given in parentheses are mathematical
F1515 Test Method for Measuring Light Stability of Resil-
conversions to SI units that are provided for information only
ient Flooring by Color Change
and are not considered standard.
2.3 ANSI Standards:
1.3 The following precautionary statement pertains only to
ANSI/ASQC Z1.4 Sampling Procedures and Tables for
the test method portion, Section 10, of this specification: This
3
Inspection by Attributes
standard does not purport to address all the safety concerns, if
any, associated with its use. It is the responsibility of the user
3. Terminology
of this standard to establish appropriate safety and health
3.1 Definitions—For definitions of other terms used in this
practices and determine the applicability of regulatory limita-
standard, see Terminology F141.
tions prior to use.
4. Classification
2. Referenced Documents
4.1 Rubber sheet floor covering covered by this specifica-
2.1 The following documents if the issue in effect on the
tion shall conform to the following types:
dateofthematerialpurchaseformapartofthisspecificationto
4.1.1 Type I—Homogeneous rubber sheet floor covering
the extent referenced herein:
2 with backing:
2.2 ASTM Standards:
4.1.1.1 Fibrous backing, and
D412 Test Methods for Vulcanized Rubber and Thermo-
4.1.1.2 Foamed rubber backing.
plastic Elastomers—Tension
4.1.2 Type II—Layered rubber sheet floor covering with
D883 Terminology Relating to Plastics
backing:
D1566 Terminology Relating to Rubber
4.1.2.1 Fibrous backing, and
D2240 Test Method for Rubber Property—Durometer
4.1.2.2 Foamed rubber backing.
Hardness
4.2 The above may have either smooth, embossed, or
F141 Terminology Relating to Resilient Floor Coverings
molded pattern surfaces.
F387 Test Method for Measuring Thickness of Resilient
4.3 These products shall not contain asbestos.
Floor Covering With Foam Layer
F410 Test Method for Wear Layer Thickness of Resilient
5. Ordering Information
Floor Coverings by Optical Measurement
5.1 Purchasers shall state whether this specification is to be
F710 Practice for Preparing Concrete Floors to Receive
used, select the preferred options permitted herein and include
Resilient Flooring
the following information in the invitation to bid or purchase
order:
1
This specification is under the jurisdiction of ASTM Committee F06 on 5.1.1 Title, number, and date of this specification,
Resilient Floor Coverings and is the direct responsibility of Subcommittee F06.80
5.1.2 Type, color, and surface (see Section 4 and Section 6),
on Specifications.
5.1.3 Quantity, in square feet, square yards, or square
Current edition approved May 1, 2010. Published June 2010. Originally
´1
metres,
approved in 1998. Last previous edition approved in 2009 as F1860 – 04(2009) .
DOI: 10.1520/F1860-10.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
3
Standards volume information, refer to the standard’s Document Summary page on Available fromAmerican National Standards Institute (ANSI), 25 W. 43rd St.,
the ASTM website. 4th Floor, New York, NY 10036, http://www.ansi.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Please contact ASTM International (www.astm.org) for the latest information.
F1860 – 10
5.1.4 Thickness required. (see 8.3), floors above-, on-, or below-grade when installed according to
5.1.5 Overall thickness, if molded pattern flooring is speci- manufacturer’s installation recommendations.
6.6 Color, Pattern, and Wearing Surface—The color, pat-
fied (see
...

This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
´1
Designation:F1860–04 (Reapproved 2009) Designation: F1860 – 10
Standard Specification for
1
Rubber Sheet Floor Covering With Backing
This standard is issued under the fixed designation F1860; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1
´ NOTE—Removed the year/date from ANSI/ASQC Z1.4 editorially in May 2009.
1. Scope
1.1 This specification covers the requirements for the compound and physical characteristics of rubber sheet floor covering
having a rubber wear layer with backing. Products may also contain intermediate layers.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.3 The following precautionary statement pertains only to the test method portion, Section 10, of this specification: This
standard does not purport to address all the safety concerns, if any, associated with its use. It is the responsibility of the user of
this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior
to use.
2. Referenced Documents
2.1 The following documents if the issue in effect on the date of the material purchase form a part of this specification to the
extent referenced herein:
2
2.2 ASTM Standards:
D412 Test Methods for Vulcanized Rubber and Thermoplastic ElastomersTension
D883 Terminology Relating to Plastics
D1566 Terminology Relating to Rubber
D2240 Test Method for Rubber PropertyDurometer Hardness
F141 Terminology Relating to Resilient Floor Coverings
F387 Test Method for Measuring Thickness of Resilient Floor Covering With Foam Layer
F410 Test Method for Wear Layer Thickness of Resilient Floor Coverings by Optical Measurement
F710 Practice for Preparing Concrete Floors to Receive Resilient Flooring
F925 Test Method for Resistance to Chemicals of Resilient Flooring
F970 Test Method for Static Load Limit
F1482 Practice for Installation and Preparation of Panel Type Underlayments to Receive Resilient Flooring
F1514 Test Method for Measuring Heat Stability of Resilient Flooring by Color Change
F1515 Test Method for Measuring Light Stability of Resilient Flooring by Color Change
2.3 ANSI Standards:
3
ANSI/ASQC Z1.4 Sampling Procedures and Tables for Inspection by Attributes
3. Terminology
3.1 Definitions—For definitions of other terms used in this standard, see Terminology F141.
4. Classification
4.1 Rubber sheet floor covering covered by this specification shall conform to the following types:
4.1.1 Type I—Homogeneous rubber sheet floor covering with backing:
4.1.1.1 Fibrous backing, and
1
This specification is under the jurisdiction of ASTM Committee F06 on Resilient Floor Coverings and is the direct responsibility of Subcommittee F06.80 on
Specifications.
Current edition approved May 1, 2009.2010. Published July 2009.June 2010. Originally approved in 1998. Last previous edition approved in 20042009 as F1860 –
´1
04(2009) . DOI: 10.1520/F1860-04R09E01.10.1520/F1860-10.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
F1860 – 10
4.1.1.2 Foamed rubber backing.
4.1.2 Type II—Layered rubber sheet floor covering with backing:
4.1.2.1 Fibrous backing, and
4.1.2.2 Foamed rubber backing.
4.2 The above may have either smooth, embossed, or molded pattern surfaces.
4.3 These products shall not contain asbestos.
5. Ordering Information
5.1 Purchasers shall state whether this specification is to be used, select the preferred options permitted herein and include the
following information in the invitation to bid or purchase order:
5.1.1 Title, number, and date of this specification,
5.1.2 Type, color, and surface (see Section 4 and Section 6),
5.1.3 Quantity, in square feet, square yards, or square metres,
5.1.4 Thickness re
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM F3441-23a(Guide)
Standard Guide for Measurement of pH Below Resilient Flooring Installations

SIGNIFICANCE AND USE
4.1 There is typically a higher concentration of soluble alkali salts in the surface region of a concrete slab due to the initial bleeding process of a freshly placed concrete slab. If after a resilient floor covering material is installed there is sufficient moisture within the slab to place these salts into solution a potentially damaging high pH solution can develop beneath the installed material.  
4.2 Results obtained through the use of this guide indicate the comparative pH of reagent water placed on properly prepared concrete slab surfaces only at the time of the procedure and in the specific locations evaluated.  
4.3 If pre-installation surface pH evaluation is required by the manufacturer of the resilient flooring, adhesive, patching/underlayment products or project specifications, their instructions and limitations should be consulted.
SCOPE
1.1 This guide discusses procedures that may be used for evaluating the comparative change in pH of reagent water placed on the surface of a properly prepared concrete slab surface.  
1.2 This guide is intended to be used in conjunction with the flat surface electrode pH meter manufacturer’s calibration procedures, operation instructions, and interpretive data where available.  
1.3 This guide is intended to be used in conjunction with the pH paper manufacturer’s instructions, product shelf life, and interpretive data where available.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use Some specific hazards statements are given in Section 9 on Hazards.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    4 pages
    English language
    sale 15% off
  • Guide
    4 pages
    English language
    sale 15% off
ASTM
ASTM F3404-23a(Specification)
Standard Specification for Heterogeneous Polyurethane Tile or Plank Flooring

SCOPE
1.1 This specification covers the requirements for the compound and physical characteristics of heterogeneous polyurethane tile or plank flooring that is printed or otherwise decorated to achieve a pattern or visual and protected by a clear wear layer.  
1.2 This specification covers heterogeneous polyurethane tile or plank flooring that shall be composed of binder, fillers, and pigments. The binder shall consist of one or more resins of polyurethane, polyurethane copolymers or other suitable or any desirable combination. Other suitable polymeric resins may be incorporated as part of the binder, provided the polyurethane portion of the binder is greater than 60 % in the base layer.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM F141-23(Terminology)
Standard Terminology Relating to Resilient Floor Coverings
  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM F1516-23(Practice)
Standard Practice for Sealing Seams of Resilient Flooring Products by the Heat Weld Method (when Recommended)

SIGNIFICANCE AND USE
4.1 Seams in some resilient flooring are heat sealed to prevent openings from forming between cut edges and to prevent penetrations of dirt, liquids, etc., into the seams. Decorative appearances may also be achieved using contrasting heat weld thread (rod).
SCOPE
1.1 This practice covers the instructions and precautions to be observed to ensure satisfactory performance of seams in resilient flooring sealed by the heat weld method.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. See precaution information in 6.1.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM F693-01(2023)(Practice)
Standard Practice for Sealing Seams of Resilient Sheet Flooring Products by Use of Liquid Seam Sealers

SIGNIFICANCE AND USE
4.1 Seams in some sheet resilient flooring are sealed to prevent openings from forming between cut edges and prevent penetrations of dirt, liquids, etc., into the seams.
SCOPE
1.1 This practice covers the instructions and precautions to be observed to ensure satisfactory performance of seams in sheet resilient flooring sealed with liquid seam sealers.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM F3191-23(Practice)
Standard Practice for Field Determination of Substrate Water Absorption (Porosity) for Substrates to Receive Resilient Flooring

SIGNIFICANCE AND USE
5.1 The ability of a substrate surface to readily absorb water is a key indicator in determining how to correctly install many types of flooring adhesives, primers, self-leveling underlayments, and other products. Several flooring industry publications such as CRI’s Carpet Installation Standard, RFCI’s Recommended Installation Practice for Homogenous Sheet Flooring, Fully-Adhered, as well as most flooring, adhesive, primer, and underlayment manufacturers reference substrate surface porosity criteria in their application instructions since this directly impacts the spread rate of directly applied material, the open time, and other critical installation factors.  
5.2 Installing flooring products over low or non-absorptive (sometimes referred to as “non-porous”) substrates such as densely machine-troweled concrete, mature and well-hydrated concrete, existing resilient flooring, polymer terrazzo and others may require adjustments to the surface preparation method or product selection to ensure a successful installation.  
5.3 Use this practice to obtain a qualitative assessment of substrate water absorption (porosity) and whether or not that substrate should be regarded as porous/absorptive or non-porous/non-absorptive as these terms relate to the installation of resilient floor coverings, adhesives, self-leveling underlayments, primers, and other products. This practice will produce results directly applicable to determining appropriate surface preparation requirements in accordance with manufacturer’s specifications, but it is in no way meant to replace published manufacturer’s literature regarding the determination of substrate water absorption (porosity) and the impact such has, if any, on substrate preparation requirements and on the installation of their respective materials.  
5.4 Substrates that evidence immediate absorption, are chalky or dusty, or have varying degrees of absorption may require priming or other additional surface preparation prior to subseq...
SCOPE
1.1 This practice covers the determination of whether or not a substrate surface, in lieu of written instruction from a product manufacturer, is considered porous or non-porous prior to the installation of resilient flooring materials.  
1.2 Although carpet tiles, carpet, wood flooring, coatings, films, paints, self-leveling and trowel-grade underlayments, primers, and other associated products are not specifically intended to be included in the category of resilient floor coverings, the procedures included in this practice may be useful for assessing the substrate water absorption for substrates to receive such materials.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Some specific hazards statements are given in Section 6 on Hazards.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM F3403-23(Specification)
Standard Specification for Heterogeneous Polyurethane Sheet Flooring

SCOPE
1.1 This specification covers the requirements for the compound and physical characteristics of heterogeneous polyurethane sheet flooring that is printed or otherwise decorated to achieve a pattern or visual and protected by a clear wear layer.  
1.2 This specification covers heterogeneous polyurethane sheet flooring that shall be composed of binder, fillers, and pigments. The binder shall consist of one or more resins of polyurethane, polyurethane copolymers or other suitable or any desirable combination. Other suitable polymeric resins may be incorporated as part of the binder, provided the polyurethane portion of the binder is greater than 60 % in the base layer.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM F710-22(Practice)
Standard Practice for Preparing Concrete Floors to Receive Resilient Flooring

ABSTRACT
This practice covers the procedure for determining the acceptability of concrete floors for the installation of resilient flooring. It also includes suggestions for ensuring that the constructed concrete floor is acceptable for such installations but does not cover tests for adequacy of the concrete floor to perform structural requirements. A permanent, effective moisture vapor retarder, of the specified thickness and permeance, is required under all on- or below-grade concrete floors. Concrete floors for resilient floorings should be permanently dry, clean, smooth, structurally sound, and free of substances that may prevent adhesive bonding. Surface cracks, grooves, depression, control joints or other non-moving joints, and other irregularities should be filled or smoothed with latex patching or a recommended underlayment compound. The surface of the floor should be cleaned by scraping, brushing, vacuuming, or any other method. All concrete slabs should be tested for moisture regardless of age or grade level while all concrete floors should be tested for pH before installing resilient flooring.
SCOPE
1.1 This practice covers the determination of the acceptability of a concrete floor for the installation of resilient flooring.  
1.2 This practice includes suggestions for the construction of a concrete floor to ensure its acceptability for installation of resilient flooring.  
1.3 This practice does not cover the adequacy of the concrete floor to perform its structural requirements.  
1.4 This practice covers the necessary preparation of concrete floors prior to the installation of resilient flooring.  
1.5 This practice does not supersede in any manner the resilient flooring or adhesive manufacturer's written instructions. Consult the individual manufacturer for specific recommendations.  
1.6 Although carpet tiles, carpet, wood flooring, coatings, films, and paints are not specifically intended to be included in the category of resilient floor coverings, the procedures included in this practice may be useful for preparing concrete floors to receive such finishes.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. See 4.1.1, 7.1.1, and 7.1.2 for specific warning statements.  
1.8 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    10 pages
    English language
    sale 15% off
  • Standard
    10 pages
    English language
    sale 15% off
ASTM
ASTM F1037-18(2022)(Test Method)
Standard Test Method for Visual Rating of Appearance of Resilient Floors

SIGNIFICANCE AND USE
4.1 Ratings are developed by some subjective or comparative evaluation criteria, or both, of a sample(s) to some reference criteria or when compared to a control sample. These parameters generally include change in gloss, color, surface texture, alterations to pattern and possibly restorability of appearance with normal maintenance procedures, including the use of finishes or buffing. Rating is done by a qualified individual or preferably by a panel of qualified observers under specified lighting conditions in accordance with prescribed procedures.
SCOPE
1.1 This test method is intended to provide a numerical rating system for classification of resilient floors during the various stages of their wear life in relation to their condition, as perceived by a knowledgeable user.  
1.2 This test method is intended to allow comparison between two or more samples or groups of samples for differences in visual appearance.  
1.3 This method provides recommended viewing conditions and lighting for rating visual differences between samples or groups of samples.  
1.4 This method can be utilized to evaluate change in visual appearance before and after some specified test condition exposure, for example, in service wear due to foot traffic, or other tests where change in appearance might occur.  
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.6 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental health practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM F410-08(2022)(Test Method)
Standard Test Method for Wear Layer Thickness of Resilient Floor Coverings by Optical Measurement

SIGNIFICANCE AND USE
3.1 This test method is applicable for wear layers with a minimum thickness of 0.001 in. (0.02 mm) to a maximum thickness of 0.1 in. (2.54 mm), where measurements within 0.0005 in. or 0.01 mm are tolerable.
SCOPE
1.1 This test method covers the determination of the thickness of the wear layer of resilient non-textile floor coverings, in tile or sheet form, with or without felt backing or foam layer, by optical measurement.  
1.2 This test method is applicable for wear layers with a minimum thickness of 0.0004 in. (0.01 mm) to a maximum thickness of 0.1 in. (2.54 mm), where measurements within 0.0001 in. or 0.0025 mm are tolerable.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off