ASTM F2433-05(2018)
(Test Method)Standard Test Method for Determining Thermoplastic Pipe Wall Stiffness
Standard Test Method for Determining Thermoplastic Pipe Wall Stiffness
SIGNIFICANCE AND USE
5.1 The performance under bending and compression load of a thermoplastic plastic pipe wall design obtained by this method can be used for the following:
5.1.1 To determine the stiffness of the pipe wall section. This is a function of the pipe dimensions, the wall design, the arc length tested, and the physical properties of the material of which the pipe is made.
5.1.2 To compare the characteristics of various thermoplastic pipe wall designs.
5.1.3 To compare the characteristics of various plastics in pipe form.
5.1.4 To study the interrelations of dimensions, materials, and deformation properties of thermoplastic pipe designs.
5.1.5 To measure the deformation and load-resistance at any of several significant events which may occur during the test.
5.1.6 To provide a reasonable quality control/quality assurance test for very large diameter plastic pipes.
5.2 The time-dependent pipe wall stiffness of a thermoplastic pipe obtained by this test method may used for the following:
5.2.1 To predict the residual stiffness of the pipe wall in bending and compression at all times after initial loading.
5.2.2 For purposes of design, to determine a modulus of relaxation under sustained loads.
5.2.3 To quantify the influence of material formulations of thermoplastics on the modulus of relaxation.
5.2.4 To study the influence of geometric patterns of wall profiles on the modulus of relaxation.
5.3 The time-independent reduction of wall thickness at springline may be used for the following:
5.3.1 For pipe wall stiffness, to quantify the efficiency of all wall profiles of any material composition and a given geometry with that of a solid uniform thickness wall.
SCOPE
1.1 This test method covers the determination of the load-deflection behavior of thermoplastic pipe wall sections under parallel plate loading conditions.
Note 1: These are not full pipe section tests, but pipe wall segment tests. The results of these tests will be different from pipe stiffness tests per Test Method D2412, although they may be proportional. This test provides quite different information, including stress relaxation under constant strain, and comparisons of the function and stiffness of different pipe wall designs or materials.
1.2 This test method covers a loading test for determining the wall stiffness of a thermoplastic-pipe wall under a combined load of bending and compression. Changes in pipe wall profile geometry under load may also be determined.
1.3 This test method covers thermoplastic pipe.
1.4 The characteristics determined by this test method are wall stiffness and changes in profile wall dimensions at specific deformations.
1.5 The characteristics determined by this test method are wall stiffness, profile wall efficiency, and for some wall elements stability at specific Strain levels.
1.6 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.7 The text of this specification references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.
1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the De...
General Information
Relations
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: F2433 − 05 (Reapproved 2018)
Standard Test Method for
Determining Thermoplastic Pipe Wall Stiffness
This standard is issued under the fixed designation F2433; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope mental practices and determine the applicability of regulatory
limitations prior to use.
1.1 This test method covers the determination of the load-
1.9 This international standard was developed in accor-
deflection behavior of thermoplastic pipe wall sections under
dance with internationally recognized principles on standard-
parallel plate loading conditions.
ization established in the Decision on Principles for the
NOTE 1—These are not full pipe section tests, but pipe wall segment
Development of International Standards, Guides and Recom-
tests.Theresultsofthesetestswillbedifferentfrompipestiffnesstestsper
TestMethodD2412,althoughtheymaybeproportional.Thistestprovides
mendations issued by the World Trade Organization Technical
quite different information, including stress relaxation under constant
Barriers to Trade (TBT) Committee.
strain, and comparisons of the function and stiffness of different pipe wall
designs or materials.
2. Referenced Documents
1.2 This test method covers a loading test for determining
2.1 ASTM Standards:
the wall stiffness of a thermoplastic-pipe wall under a com-
D618 Practice for Conditioning Plastics for Testing
bined load of bending and compression. Changes in pipe wall
D695 Test Method for Compressive Properties of Rigid
profile geometry under load may also be determined.
Plastics
1.3 This test method covers thermoplastic pipe.
D883 Terminology Relating to Plastics
D1600 Terminology forAbbreviatedTerms Relating to Plas-
1.4 The characteristics determined by this test method are
tics
wallstiffnessandchangesinprofilewalldimensionsatspecific
D2122 Test Method for Determining Dimensions of Ther-
deformations.
moplastic Pipe and Fittings
1.5 The characteristics determined by this test method are
D2412 Test Method for Determination of External Loading
wall stiffness, profile wall efficiency, and for some wall
Characteristics of Plastic Pipe by Parallel-Plate Loading
elements stability at specific Strain levels.
F412 Terminology Relating to Plastic Piping Systems
1.6 The values stated in SI units are to be regarded as the
2.2 AASHTO Standards:
standard. The values given in parentheses are for information
M 252 Standard Specification for Corrugated Polyethylene
only.
Drainage Pipe
1.7 The text of this specification references notes and M 294 Standard Specification for Corrugated Polyethylene
Pipe, 300- to 1500-mm Diameter
footnotes that provide explanatory material. These notes and
footnotes (excluding those in tables and figures) shall not be
3. Terminology
considered as requirements of the specification.
3.1 Definitions—Definitions are in accordance with Termi-
1.8 This standard does not purport to address all of the
nology F412, and abbreviations are in accordance with Termi-
safety concerns, if any, associated with its use. It is the
nology D1600, unless otherwise specified.
responsibility of the user of this standard to establish appro-
priate safety and health practices and determine the applica-
3.2 Definitions of Terms Specific to This Standard:
bility of regulatory limitations prior to use.This standard does
3.2.1 chord shortening, n—the ratio of the reduction in pipe
not purport to address all of the safety concerns, if any,
sectionchordshorteningtotheinitialchordlengthexpressedas
associated with its use. It is the responsibility of the user of this
a percentage.
standard to establish appropriate safety, health, and environ-
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
This test method is under the jurisdiction of ASTM Committee F17 on Plastic contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Piping Systems and is the direct responsibility of Subcommittee F17.40 on Test Standards volume information, refer to the standard’s Document Summary page on
Methods. the ASTM website.
CurrenteditionapprovedFeb.1,2018.PublishedJuly2018.Originallyapproved Available from American Association of State Highway and Transportation
in 2005. Last previous edition approved in 2013 as F2433–05(2013). DOI: Officials (AASHTO), 444 N. Capitol St., NW, Suite 249, Washington, DC 20001,
10.1520/F2433-05R18. http://www.transportation.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
F2433 − 05 (2018)
3.2.2 ∆y, n—measured change in chord length (in the rate of approach to one another. Load-deflection data of the
directionofloadapplication)expressedinmillimeters(inches). wall section in combined bending and compression are ob-
tained. Change in pipe wall thickness at the center of the
3.2.2.1 compressive deformation, n—the measured change
section (springline) is determined. If cracking, crazing,
of the inside diameter in the direction of load application
delamination, rupture, or buckling occurs, the corresponding
expressed in millimeters (or inches).
load, deflection, and/or time are recorded.
3.2.3 load (F), n—the force applied to the wall section to
NOTE 2—If this test method is incorporated in a product standard it
produce or maintain a given percent chord length shortening at
would be necessary to define the arc length to be tested. There are,
any given unit of time; expressed as Newtons per meter however, many reasons various arc lengths might be tested, especially as
a research or product development tool. Large arc lengths are primarily in
(pounds-force per linear inch).
bending, while short arc lengths are primarily in compression.
3.2.4 meanradius(r),n—themid-wallradiusdeterminedby
subtractingtheaveragewallthicknessfromtheaverageoutside
5. Significance and Use
diameter and dividing the difference by two; expressed in
5.1 The performance under bending and compression load
millimeters (or inches).
of a thermoplastic plastic pipe wall design obtained by this
3.2.5 time-independent pipe stiffness K(0), n—the value
method can be used for the following:
obtained by dividing the force per unit length on the curved
5.1.1 To determine the stiffness of the pipe wall section.
beam specimen by the resulting deflection in the same units at
This is a function of the pipe dimensions, the wall design, the
the % deflection prescribed and extrapolating the linear portion
arc length tested, and the physical properties of the material of
of the curve of stiffness versus % deflection to the moment of
which the pipe is made.
application of load.
5.1.2 To compare the characteristics of various thermoplas-
3.2.6 time-dependent residual curved beam stiffness K(t)
tic pipe wall designs.
and residual pipe stiffness K(t), n—the value obtained by
5.1.3 To compare the characteristics of various plastics in
dividing the force per unit length on the curved beam specimen
pipe form.
by the constant target deflection in the same units, at any time
5.1.4 To study the interrelations of dimensions, materials,
t, t>0.
and deformation properties of thermoplastic pipe designs.
5.1.5 To measure the deformation and load-resistance at any
3.2.7 modulus of relaxation, n—the residual pipe stiffness
of several significant events which may occur during the test.
versus log(time).
5.1.6 To provide a reasonable quality control/quality assur-
3.2.8 residual pipe stiffness K(50y), n—the value obtained
ance test for very large diameter plastic pipes.
by extrapolating values of residual pipe stiffness versus time to
5.2 The time-dependent pipe wall stiffness of a thermoplas-
50 years.
tic pipe obtained by this test method may used for the
3.2.9 compliance C(t), n—the inverse of stiffness K(t).
following:
3.2.10 liner cracking or crazing, n—the occurrence of a
5.2.1 To predict the residual stiffness of the pipe wall in
break or network of fine breaks in the liner visible to the
bending and compression at all times after initial loading.
unaided eye.
5.2.2 For purposes of design, to determine a modulus of
3.2.11 wall cracking, n—the occurrence of a break in the
relaxation under sustained loads.
pipe wall visible to the unaided eye.
5.2.3 To quantify the influence of material formulations of
thermoplastics on the modulus of relaxation.
3.2.12 wall delamination, n—the occurrence of any separa-
tion in the components of the pipe wall visible to the unaided 5.2.4 To study the influence of geometric patterns of wall
profiles on the modulus of relaxation.
eye.
3.2.13 rupture, n—a crack or break extending entirely or
5.3 The time-independent reduction of wall thickness at
partly through the pipe wall. springline may be used for the following:
5.3.1 For pipe wall stiffness, to quantify the efficiency of all
4. Summary of Test Method wallprofilesofanymaterialcompositionandagivengeometry
with that of a solid uniform thickness wall.
4.1 The test is conducted by applying a controlled, nearly
instantaneous, load to the longitudinally cut edges of curved
6. Apparatus
beam sections cut from short lengths of pipe until a prescribed
shortening of the chord connecting the longitudinal edges is 6.1 Testing Machine—A properly calibrated compression
achieved and held constant for prescribed intervals. Load and testing machine of the constant-rate-of-crosshead movement
deformation data establish the time-independent measure of type meeting the requirements of Test Method D695 shall be
curvedbeamwallstiffnessattheinstantofloadapplication,the used to make the tests. The rate of head approach shall be 63.5
measure of efficiency of the profile wall geometry, stability of 6 2.5 mm (2.5 6 0.1 in.)/s. The machines must be capable of
the profile wall, a modulus of relaxation and long-term holding a required percent chord shorting for an extended
estimates of residual pipe wall stiffness. period of time.
4.2 Alengthofa10to120°arcsegmentofapipewall,from 6.2 Loading Grips—The load shall be applied to the speci-
onediameterlengthtoonemeterlongisloadedacrossitschord men through two parallel-axis grips. These assemblies shall be
length between two freely rotating end plates at a controlled flat, smooth, and clean. Specimen contact surfaces of platen
F2433 − 05 (2018)
shall be coated with a PTFE spray lubricant. The thickness of 6.6 Reaction Frame—The reaction frame shall be suffi-
theplatensshallbesufficientsothatnobendingordeformation ciently rigid such that the movement of the stationery platen
shall not exceed 0.05 % of the displacement of the moving
occurs during the test, but it shall not be less than 12 mm (0.5
platen.
in.). The nominal length of each grip shall equal or exceed the
specimen length but shall not be less than 1040 mm (41 in.).
7. Test Specimens
Upper and lower grips shall be free to rotate about an axis in
the plane of the applied and reacting line loads. Recommended
7.1 Test specimens shall be cut from the pipe wall, with the
arrangement of loading frame, upper and lower grips with test cuts through the wall radial and parallel through the sample
specimen are shown in Fig. 1. length. Test specimens may be the required arc length in
degrees 61° arc sections of the wall, as agreeable to the
6.3 Deformation Indicator—The change in total wall (major
manufacturer and the purchaser, but not less than 10 degrees
wall for profile wall pipe) thickness at springline, shall be
nor greater than 120 degrees. Test specimens should be a
measured with a suitable instrument meeting the requirements
minimum of 600 mm (24 in.) long, and may be as much as 900
of 4.1.2 of Test Method D695, except that the instrument shall
mm (36 in.), and for corrugated or profile pipe should be
beaccuratetothenearest0.025mm(0.001in.).Theinstrument
squarely cut in the corrugation or profile valley.
shall not affect in any way the load-deflection measurements.
NOTE 3—Standard arc lengths for specimens should be 120°, 90°, and
30°, though other arc lengths may be used within the range of 120° to 10°,
6.4 Load Sensor—The change of load with time during the
as determined by the needs of the owner, researcher, or testing laboratory.
periods of displacement (loading) and during the period of
constant displacement shall be digitally recorded with a preci- 8. Conditioning
sion of no less than 4 significant figures and at time intervals as
8.1 Condition the pipe wall section for at least 24 h in air at
noted in 9.3. The sensing element shall have a precision of
a temperature of 23 6 2 °C (73.4 6 3.6 °F), and 50 6 5%
62 % of maximum recorded value.
relative humidity and conduct the test in a room maintained at
the same temperature.
6.5 Temperature Recorder—Ambient temperature shall be
continuously recorded using a sensor capable of recording to
8.2 When a referee test is required, condition specimens for
1 °C (1.8 °F). at least 40 h at 23 6 2 °C (73.4 6 3.6 °F), and 50 6 5%
FIG. 1 Recommended Arrangement of Loading Frame, Upper & Lower Grips, and Test Specimen
F2433 − 05 (2018)
FIG. 2 Photographs of Specimen in Load Frame
relative humidity per Practice D618 Procedure A and conduct out-to-out distance, to the nearest 1 mm (0.04 in.), from the
the test under the same conditions. center of the crest to a projection of the center of an adjacent
valley on a line perpendicular to the tangent at the center of the
9. Procedure
crest. Determine the wall thickness by averaging the three
9.1 Before placing each test specimen in the test apparatus measurements.
9.1.3 For specimens prepared from AASHTO M 252M and
make the following measurements:
9.1.1 Measure, to the nearest 1 mm (0.04 in.), the longitu- AASHTO M 294M Type S pipes measure the total wall
thickness, to the nearest 1 mm (0.04 in.), at the center of the
dinal length with equally spaced parallel measurements at mid
andquarterpointsofthearcofthecurvedbeam.Determinethe crests of the outer wall corrugations, located at approximately
half and quarter points along the mid-longitudinal line of the
longitudinal length by averaging the three measurements.
9.1.2 For specimens prepared from AASHTO M 252M and curved beam. Determine the thickness by averaging the three
measurements.
AASHTO M 294M Type C pipes, at each of three points
approximately located on a mid-longitudinal line of the corru- 9.1.4 For specimens
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.