ASTM D2665-00

Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings

SCOPE
1.1 This specification covers requirements and test methods for materials, dimensions and tolerances, pipe stiffness, crush resistance, impact resistance, hydrostatic burst resistance, and solvent cement for poly(vinyl chloride) plastic drain, waste, and vent pipe and fittings. A form of marking is also included. Plastic which does not meet the material requirements specified in Section 5 is excluded. Installation procedures are given in the Appendix.  
1.2 The values stated in inch-pound units are to be regarded as the standard. The metric equivalents of inch-pound units given in parentheses may be approximate.  
1.3 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.
1.4 The following safety hazards caveat pertains only to the test methods portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

• Status: Historical
• Publication Date: 09-Aug-2001
• ICS: 23.040.20 - Plastics pipes
• Technical Committee: F17 - Plastic Piping Systems
• Drafting Committee: F17.63 - DWV

Relations

• Replaced By: ASTM D2665-01 - Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings
• Effective Date: 10-Aug-2001
• Referred By: ASTM D2672-20e1 - Standard Specification for Joints for IPS PVC Pipe Using Solvent Cement
• Effective Date: 10-Aug-2001
• Referred By: ASTM F1760-16(2020) - Standard Specification for Coextruded Poly(Vinyl Chloride) (PVC) Non-Pressure Plastic Pipe Having Reprocessed-Recycled Content
• Effective Date: 10-Aug-2001
• Referred By: ASTM F2946-12(2021) - Standard Specification for PVC Hub and Elastomeric Seal (Gasket) Tee Connection for Joining Plastic Pipe to Insitu Pipelines and Manholes
• Effective Date: 10-Aug-2001
• Referred By: ASTM F2536-17(2022) - Standard Guide for Installing Plastic DWV Piping Suspended from On-Grade Slabs
• Effective Date: 10-Aug-2001
• Referred By: ASTM D3138-21 - Standard Specification for Solvent Cements for Transition Joints Between Acrylonitrile-Butadiene-Styrene (ABS) and Poly(Vinyl Chloride) (PVC) Non-Pressure Piping Components
• Effective Date: 10-Aug-2001
• Referred By: ASTM F1499-22 - Standard Specification for Coextruded Composite Drain, Waste, and Vent Pipe (DWV)
• Effective Date: 10-Aug-2001
• Referred By: ASTM D2855-20 - Standard Practice for the Two-Step (Primer and Solvent Cement) Method of Joining Poly (Vinyl Chloride) (PVC) or Chlorinated Poly (Vinyl Chloride) (CPVC) Pipe and Piping Components with Tapered Sockets
• Effective Date: 10-Aug-2001
• Referred By: ASTM D3311-22 - Standard Specification for Drain, Waste, and Vent (DWV) Plastic Fittings Patterns
• Effective Date: 10-Aug-2001
• Referred By: ASTM F3128-23 - Standard Specification for Poly(Vinyl Chloride) (PVC) Schedule 40 Drain, Waste, and Vent Pipe with a Cellular Core
• Effective Date: 10-Aug-2001
• Referred By: ASTM F409-22 - Standard Specification for Thermoplastic Accessible and Replaceable Plastic Tube and Tubular Fittings
• Effective Date: 10-Aug-2001
• Referred By: ASTM F1866-23 - Standard Specification for Poly (Vinyl Chloride) (PVC) Plastic Schedule 40 Drainage and DWV Fabricated Fittings
• Effective Date: 10-Aug-2001
• Referred By: ASTM F2021-17(2022) - Standard Guide for Design and Installation of Plastic Siphonic Roof Drainage Systems
• Effective Date: 10-Aug-2001
• Referred By: ASTM F891-16 - Standard Specification for Coextruded Poly(Vinyl Chloride) (PVC) Plastic Pipe With a Cellular Core
• Effective Date: 10-Aug-2001
• Referred By: ASTM F1488-14(2019) - Standard Specification for Coextruded Composite Pipe
• Effective Date: 10-Aug-2001

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
Designation: D 2665 – 00 An American National Standard
Standard Specification for
Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent
1
Pipe and Fittings
This standard is issued under the fixed designation D 2665; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope D 2412 Test Method for Determination of External Loading
3
Characteristics of Plastic Pipe by Parallel-Plate Loading
1.1 This specification covers requirements and test methods
D 2444 Test Method for Impact Resistance of Thermoplas-
for materials, dimensions and tolerances, pipe stiffness, crush
3
tic Pipe and Fittings by Means of a Tup (Falling Weight)
resistance, impact resistance, hydrostatic burst resistance, and
D 2564 Specification for Solvent Cements for Poly(Vinyl
solvent cement for poly(vinyl chloride) plastic drain, waste,
3
Chloride) (PVC) Plastic Piping Systems
and vent pipe and fittings. A form of marking is also included.
D 3311 Specification for Drain, Waste, and Vent (DWV)
Plastic which does not meet the material requirements specified
3
Plastic Fittings Patterns
in Section 5 is excluded. Installation procedures are given in
F 402 Practice for Safe Handling of Solvent Cements and
the Appendix.
3
Primers Used for Joining Thermoplastic Pipe and Fittings
1.2 The values stated in inch-pound units are to be regarded
3
F 412 Terminology Relating to Plastic Piping Systems
as the standard. The metric equivalents of inch-pound units
F 1498 Specification for Taper Pipe Threads 60° for Ther-
given in parentheses may be approximate.
3
moplastic Pipe and Fittings
1.3 The text of this specification references notes, footnotes,
and appendixes which provide explanatory material. These
3. Terminology
notes and footnotes (excluding those in tables and figures) shall
3.1 Definitions—Definitions are in accordance with Termi-
not be considered as requirements of the specification.
nology F 412, and abbreviations are in accordance with Ter-
1.4 The following safety hazards caveat pertains only to the
minology D 1600, unless otherwise specified.
test methods portion, Section 7, of this specification: This
standard does not purport to address all of the safety concerns,
4. Significance and Use
if any, associated with its use. It is the responsibility of the user
4.1 The requirements of this specification are intended to
of this standard to establish appropriate safety and health
provide pipe and fittings suitable for the drainage and venting
practices and determine the applicability of regulatory limita-
of sewage and certain other liquid wastes.
tions prior to use.
NOTE 1—Industrial waste disposal lines should be installed only with
2. Referenced Documents
the specific approval of the cognizant building code authority since
chemicals not commonly found in drains and sewers and temperatures in
2.1 ASTM Standards:
excess of 180°F (82.2°C) may be encountered.
D 618 Practice for Conditioning Plastics and Electrical
2
Insulating Materials for Testing
5. Materials
D 1599 Test Method for Short-Time Hydraulic Failure Pres-
5.1 Basic Materials—The pipe and fittings shall be made of
3
sure of Plastic Pipe, Tubing, and Fittings
virgin PVC compounds meeting or exceeding the requirements
D 1600 Terminology for Abbreviated Terms Relating to
of Class 12454 as defined in Specification D 1784. This plastic
2
Plastics
contains stabilizers, lubricants, and pigments.
D 1784 Specification for Rigid Poly(Vinyl Chloride) (PVC)
5.2 Rework Material—The manufacturer shall use only his
Compounds and Chlorinated Poly(Vinyl Chloride)
2 own clean pipe or fitting rework material and the pipe or
(CPVC) Compounds
fittings produced shall meet all the requirements of this
D 2122 Test Method for Determining Dimensions of Ther-
3 specification.
moplastic Pipe and Fittings
5.3 Solvent Cement—The solvent cement used to join pipe
and fittings made to this specification shall meet the require-
1
This specification is under the jurisdiction of ASTM Committee F17 on Plastic
ments of Specification D 2564.
Piping Systems and is the direct responsibility of Subcommittee F17.63 on DWV.
Current edition approved August 10, 2000. Published November 2000. Origi-
6. Requirements
nally published as D 2665 – 68. Last previous edition D 2665 – 98.
2
Annual Book of ASTM Standards, Vol 08.01.
6.1 General—The pipe and fittings shall be homogeneous
3
Annual Book of ASTM Standards, Vol 08.04.
Copyright © ASTM, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ---------------------
...