Standard Test Method for Preparation and Testing of Controlled Low Strength Material (CLSM) Test Cylinders

SIGNIFICANCE AND USE
This test method provides standardized requirements for the preparation, curing, transporting and testing of test cylinders of CLSM under field conditions by replicating a “field cure” of the material.
If the cylinders are field cured, as stipulated herein, the resulting compressive strength test data may be used for the following purposes:
Acceptance testing for specified strength,
Checking the adequacy of mixture proportions for strength,
Quality control,
Determination of whether the CLSM is capable of being put in service,
Adequacy of curing.
CLSM is typically used as a backfill material around structures, particularly in confined or limited spaces. Compressive strength testing is performed to assist in the design of the mix and to serve as a quality control technique during construction. Mix design is typically based on 28-day strengths and construction control tests performed 7 days after placement. The compressive strength(s) and other test age(s) will vary according to the requirements for the end product. Additional information on the use and history of CLSM is contained in Appendix X1.
This test is one of a series of quality control tests that can be performed on CLSM during construction to monitor compliance with specification requirements. The other tests that can be used during construction control of CLSM are Practice D5971 and Test Methods D6023, D6024, and D6103.
There are many other combinations of soil, cement, fly ash (cementitious or not), admixtures, water quality or other materials that could be tested using this method. The mixtures will vary depending on the intended use, availability of materials, and placement requirements.
Note 1—The quality of the result produced by this standard is dependent on the competence of the personnel performing it, and the suitability of the equipment and facilities used. Agencies that meet the criteria of Practice D3740 are generally considered capable of competent and objective testing/samp...
SCOPE
1.1 This test method covers procedures for the preparation, curing, transporting and testing of cylindrical test specimens of controlled low strength material (CLSM) for the determination of compressive strength.  
1.2 This test method covers CLSM materials that have a higher strength than the soil but less than 8400 kPa (1200 psi). Typical strengths for most applications fall between 350 to 700 kPa (50 to 100 psi).
1.3 The CLSM used to make the molded specimens shall be sampled after all on-site adjustments have been made to the mixture proportions, including the addition of mix water and any admixtures.
1.4 This test method may be used to prepare and test cylindrical specimens of other mixtures of soil and cementitious materials, such as self-cementing fly ashes.
1.5 CLSM is also known as flowable fill, controlled density fill, soil-cement slurry, soil-cement grout, unshrinkable fill, K-Krete, and other similar names.
1.6 All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026.
1.6.1 The procedures used to specify how data are collected/recorded and calculated in this standard are regarded as the industry standard. In addition, they are representative of the significant digits that should generally be retained. The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the user’s objectives; and it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations. It is beyond the scope of this standard to consider significant digits used in analysis methods for engineering design.
1.7 The values stated in SI units are to be regarded as the standard. The inch-pound equivalents given in brackets are, in most cases, rationalized units and are shown for information only.
1.8 This standard does not ...

General Information

Status
Historical
Publication Date
14-Jan-2010
Technical Committee
Current Stage
Ref Project

Relations

Buy Standard

Standard
ASTM D4832-10 - Standard Test Method for Preparation and Testing of Controlled Low Strength Material (CLSM) Test Cylinders
English language
6 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
REDLINE ASTM D4832-10 - Standard Test Method for Preparation and Testing of Controlled Low Strength Material (CLSM) Test Cylinders
English language
6 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D4832 − 10
Standard Test Method for
Preparation and Testing of Controlled Low Strength Material
1
(CLSM) Test Cylinders
This standard is issued under the fixed designation D4832; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 1.7 The values stated in SI units are to be regarded as the
standard. The inch-pound equivalents given in brackets are, in
1.1 This test method covers procedures for the preparation,
most cases, rationalized units and are shown for information
curing,transportingandtestingofcylindricaltestspecimensof
only.
controlledlowstrengthmaterial(CLSM)forthedetermination
1.8 This standard does not purport to address all of the
of compressive strength.
safety concerns, if any, associated with its use. It is the
1.2 This test method covers CLSM materials that have a
responsibility of the user of this standard to establish appro-
higher strength than the soil but less than 8400 kPa (1200 psi).
priate safety and health practices and determine the applica-
Typicalstrengthsformostapplicationsfallbetween350to700
bility of regulatory limitations prior to use. See Section 7.
kPa (50 to 100 psi).
2. Referenced Documents
1.3 TheCLSMusedtomakethemoldedspecimensshallbe
2
sampled after all on-site adjustments have been made to the
2.1 ASTM Standards:
mixture proportions, including the addition of mix water and
C31/C31MPractice for Making and Curing Concrete Test
any admixtures.
Specimens in the Field
C39/C39MTestMethodforCompressiveStrengthofCylin-
1.4 This test method may be used to prepare and test
drical Concrete Specimens
cylindrical specimens of other mixtures of soil and cementi-
C125Terminology Relating to Concrete and Concrete Ag-
tious materials, such as self-cementing fly ashes.
gregates
1.5 CLSM is also known as flowable fill, controlled density
C192/C192MPracticeforMakingandCuringConcreteTest
fill, soil-cement slurry, soil-cement grout, unshrinkable fill,
Specimens in the Laboratory
K-Krete, and other similar names.
C470/C470MSpecification for Molds for Forming Concrete
1.6 All observed and calculated values shall conform to the Test Cylinders Vertically
guidelines for significant digits and rounding established in C617Practice for Capping Cylindrical Concrete Specimens
Practice D6026. C1231/C1231MPractice for Use of Unbonded Caps in
DeterminationofCompressiveStrengthofHardenedCon-
1.6.1 Theproceduresusedtospecifyhowdataarecollected/
crete Cylinders
recorded and calculated in this standard are regarded as the
D653Terminology Relating to Soil, Rock, and Contained
industry standard. In addition, they are representative of the
Fluids
significant digits that should generally be retained. The proce-
D3740Practice for Minimum Requirements for Agencies
dures used do not consider material variation, purpose for
Engaged in Testing and/or Inspection of Soil and Rock as
obtaining the data, special purpose studies, or any consider-
Used in Engineering Design and Construction
ations for the user’s objectives; and it is common practice to
D5971Practice for Sampling Freshly Mixed Controlled
increase or reduce significant digits of reported data to be
Low-Strength Material
commensuratewiththeseconsiderations.Itisbeyondthescope
D6023Test Method for Density (Unit Weight), Yield, Ce-
of this standard to consider significant digits used in analysis
ment Content, and Air Content (Gravimetric) of Con-
methods for engineering design.
trolled Low-Strength Material (CLSM)
D6024Test Method for Ball Drop on Controlled Low
1
ThistestmethodisunderthejurisdictionofASTMCommitteeD18onSoiland
RockandisthedirectresponsibilityofSubcommitteeD18.15onStabilizationWith
2
Admixtures. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved Jan. 15, 2010. Published March 2010. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 1988. Last previous edition approved in 2002 as D4832–02. DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/D4832-10. the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D4832 − 10
Strength Material (CLSM) to Determine Suitability for compliance with specification requirements. The other tests
Load Application that can be used during construction control of CLSM are
D6026Practice for Using Significant Digits in Geotechnical Practice D5971 and Test Methods D6023, D6024
...

This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:D4832–02 Designation: D4832 – 10
Standard Test Method for
Preparation and Testing of Controlled Low Strength Material
1
(CLSM) Test Cylinders
This standard is issued under the fixed designation D4832; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (ϵ) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This test method covers procedures for the preparation, curing, transporting and testing of cylindrical test specimens of
controlled low strength material (CLSM) for the determination of compressive strength.
1.2This test method also may be used to prepare and test specimens of other mixtures of soil and cementitious materials, such
as self-cementing fly ashes.
1.3CLSM is also known as flowable fill, controlled density fill, soil-cement slurry, soil-cement grout, unshrinkable fill, K-Krete,
and other similar names.
1.4The values stated in SI units are to be regarded as the standard. The inch-pound equivalents are shown for information only.
1.5
1.2 This test method covers CLSM materials that have a higher strength than the soil but less than 8400 kPa (1200 psi).Typical
strengths for most applications fall between 350 to 700 kPa (50 to 100 psi).
1.3 TheCLSMusedtomakethemoldedspecimensshallbesampledafterallon-siteadjustmentshavebeenmadetothemixture
proportions, including the addition of mix water and any admixtures.
1.4 This test method may be used to prepare and test cylindrical specimens of other mixtures of soil and cementitious materials,
such as self-cementing fly ashes.
1.5 CLSMisalsoknownasflowablefill,controlleddensityfill,soil-cementslurry,soil-cementgrout,unshrinkablefill,K-Krete,
and other similar names.
1.6 All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice
D6026.
1.6.1 Theproceduresusedtospecifyhowdataarecollected/recordedandcalculatedinthisstandardareregardedastheindustry
standard. In addition, they are representative of the significant digits that should generally be retained.The procedures used do not
consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the user’s objectives;
and it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations.
It is beyond the scope of this standard to consider significant digits used in analysis methods for engineering design.
1.7 The values stated in SI units are to be regarded as the standard. The inch-pound equivalents given in brackets are, in most
cases, rationalized units and are shown for information only.
1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use. See Section 7.
2. Referenced Documents
2
2.1 ASTM Standards:
C31/C31M Practice for Making and Curing Concrete Test Specimens in the Field
C39/C39M Test Method for Compressive Strength of Cylindrical Concrete Specimens
C125 Terminology Relating to Concrete and Concrete Aggregates
C192/C192M Practice for Making and Curing Concrete Test Specimens in the Laboratory
C470/C470M Specification for Molds for Forming Concrete Test Cylinders Vertically
1
This test method is under the jurisdiction of ASTM Committee D18 on Soil and Rock and is the direct responsibility of Subcommittee D18.15 on Stabilization With
Admixtures.
e1
Current edition approved July 10, 2002. Published September 2002. Originally published as D4832–88. Last previous edition D4832–95 DOI: 10.1520/D4832-02.
Current edition approved Jan. 15, 2010. Published March 2010. Originally approved in 1988. Last previous edition approved in 2002 as D4832 – 02. DOI:
10.1520/D4832-10.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
D4832 – 10
C617 Practice for Cappi
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.