ASTM D97-11
(Test Method)Standard Test Method for Pour Point of Petroleum Products
Standard Test Method for Pour Point of Petroleum Products
SIGNIFICANCE AND USE
The pour point of a petroleum specimen is an index of the lowest temperature of its utility for certain applications.
SCOPE
1.1 This test method covers and is intended for use on any petroleum product. A procedure suitable for black specimens, cylinder stock, and nondistillate fuel oil is described in 8.8. The cloud point procedure formerly part of this test method now appears as Test Method D 2500.
1.2 Currently there is no ASTM test method for automated Test Method D 97 pour point measurements.
1.3 Several ASTM test methods offering alternative procedures for determining pour points using automatic apparatus are available. None of them share the same designation number as Test Method D 97. When an automatic instrument is used, the ASTM test method designation number specific to the technique shall be reported with the results. A procedure for testing the pour point of crude oils is described in Test Method D 5853.
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D97 − 11
Designation:15/95
Standard Test Method for
1
Pour Point of Petroleum Products
ThisstandardisissuedunderthefixeddesignationD97;thenumberimmediatelyfollowingthedesignationindicatestheyearoforiginal
adoptionor,inthecaseofrevision,theyearoflastrevision.Anumberinparenthesesindicatestheyearoflastreapproval.Asuperscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope* 1.6 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the
1.1 This test method covers and is intended for use on any
2 responsibility of the user of this standard to establish appro-
petroleum product. Aprocedure suitable for black specimens,
priate safety and health practices and determine the applica-
cylinderstock,andnondistillatefueloilisdescribedin8.8.The
bility of regulatory limitations prior to use.
cloud point procedure formerly part of this test method now
appears as Test Method D2500.
2. Referenced Documents
1.2 Currently there is no ASTM test method for automated
3
2.1 ASTM Standards:
Test Method D97 pour point measurements.
D117Guide for Sampling, Test Methods, and Specifications
1.3 Several ASTM test methods offering alternative proce-
for Electrical Insulating Oils of Petroleum Origin
dures for determining pour points using automatic apparatus
D396Specification for Fuel Oils
areavailable.Noneofthemsharethesamedesignationnumber
D2500Test Method for Cloud Point of Petroleum Products
as Test Method D97. When an automatic instrument is used,
D5853Test Method for Pour Point of Crude Oils
the ASTM test method designation number specific to the
D6300Practice for Determination of Precision and Bias
technique shall be reported with the results. A procedure for
Data for Use in Test Methods for Petroleum Products and
testing the pour point of crude oils is described inTest Method
Lubricants
D5853.
E1Specification for ASTM Liquid-in-Glass Thermometers
1.4 The values stated in SI units are to be regarded as
2.2 Energy Institute Standards:
standard. No other units of measurement are included in this
4
Specifications for IP Standard Thermometers
standard.
1.5 WARNING—Mercury has been designated by many
3. Terminology
regulatory agencies as a hazardous material that can cause
3.1 Definitions:
central nervous system, kidney and liver damage. Mercury, or
3.1.1 black oil, n—lubricant containing asphaltic materials.
its vapor, may be hazardous to health and corrosive to
Blackoilsareusedinheavy-dutyequipmentapplications,such
materials.Cautionshouldbetakenwhenhandlingmercuryand
as mining and quarrying, where extra adhesiveness is desired.
mercury containing products. See the applicable product Ma-
3.1.2 cylinder stock, n—lubricant for independently lubri-
terial Safety Data Sheet (MSDS) for details and EPA’s
cated engine cylinders, such as those of steam engines and air
website—http://www.epa.gov/mercury/faq.htm—for addi-
compressors. Cylinder stock are also used for lubrication of
tional information. Users should be aware that selling mercury
valves and other elements in the cylinder area.
and/or mercury containing products into your state or country
may be prohibited by law.
3.1.3 pour point, n—in petroleum products, the lowest
temperature at which movement of the test specimen is
observed under prescribed conditions of test.
1
This test method is under the jurisdiction of ASTM Committee D02 on
Petroleum Products and Lubricants and is the direct responsibility of Subcommittee
D02.07 on Flow Properties.
CurrenteditionapprovedJune1,2011.PublishedJuly2011.Originallyapproved
3
in 1927, replacing D47. Last previous edition approved in 2009 as D97–09. DOI: For referenced ASTM standards, visit the ASTM website, www.astm.org, or
10.1520/D0097-11. contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
In the IP, this test method is under the jurisdiction of the Standardization Standards volume information, refer to the standard’s Document Summary page on
Committee. This test method was adopted as a joint ASTM-IP Standard in 1965. the ASTM website.
2 4
Statements defining this test and its significance when applied to electrical MethodsforAnalysisandTesting,IPStandardsforPetroleumanditsProducts,
insulating oils of mineral origin will be found in Guide D117. Part I, Vol 2.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D97−11
NOTE 1—Dimensions are in millimetres (not to scale).
FIG. 1 Apparatus for Pour Point Test
3.1.4 residual fuel, n—a liquid fuel containing bottoms
Temperature Thermometer
Number
rema
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:D97–09 Designation:D97–11
Designation: 15/95
Standard Test Method for
1
Pour Point of Petroleum Products
ThisstandardisissuedunderthefixeddesignationD97;thenumberimmediatelyfollowingthedesignationindicatestheyearoforiginal
adoptionor,inthecaseofrevision,theyearoflastrevision.Anumberinparenthesesindicatestheyearoflastreapproval.Asuperscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope*
2
1.1This1.1 Thistestmethodcoversandisintendedforuseonanypetroleumproduct. Aproceduresuitableforblackspecimens,
cylinder stock, and nondistillate fuel oil is described in 8.8. The cloud point procedure formerly part of this test method now
appears as Test Method D2500.
1.2 Currently there is no ASTM test method for automated Test Method D97 pour point measurements.
1.3 Several ASTM test methods offering alternative procedures for determining pour points using automatic apparatus are
available.NoneofthemsharethesamedesignationnumberasTestMethodD97.Whenanautomaticinstrumentisused,theASTM
test method designation number specific to the technique shall be reported with the results.Aprocedure for testing the pour point
of crude oils is described in Test Method D5853.
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.5
1.5 WARNING—Mercury has been designated by many regulatory agencies as a hazardous material that can cause central
nervous system, kidney and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution
should be taken when handling mercury and mercury containing products. See the applicable product Material Safety Data Sheet
(MSDS) for details and EPA’s website—http://www.epa.gov/mercury/faq.htm—for additional information. Users should be aware
that selling mercury and/or mercury containing products into your state or country may be prohibited by law.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
3
2.1 ASTM Standards:
D117 Guide for Sampling, Test Methods, and Specifications for Electrical Insulating Oils of Petroleum Origin
D396 Specification for Fuel Oils
D2500 Test Method for Cloud Point of Petroleum Products
D5853 Test Method for Pour Point of Crude Oils
D6300 Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants
E1 Specification for ASTM Liquid-in-Glass Thermometers
2.2 Energy Institute Standards:
4
Specifications for IP Standard Thermometers
1
This test method is under the jurisdiction ofASTM Committee D02 on Petroleum Products and Lubricants and is the direct responsibility of Subcommittee D02.07 on
Flow Properties.
Current edition approved April 15, 2009.June 1, 2011. Published April 2009.July 2011. Originally approved in 1927, replacing D47. Last previous edition approved in
20082009 as D97–08. D97–09. DOI: 10.1520/D0097-11.
In the IP, this test method is under the jurisdiction of the Standardization Committee. This test method was adopted as a joint ASTM-IP Standard in 1965. DOI:
10.1520/D0097-09.
2
Statements defining this test and its significance when applied to electrical insulating oils of mineral origin will be found in Guide D117.
3
ForreferencedASTMstandards,visittheASTMwebsite,www.astm.org,orcontactASTMCustomerServiceatservice@astm.org.ForAnnualBookofASTMStandards
volume information, refer to the standard’s Document Summary page on the ASTM website.
4
Methods for Analysis and Testing, IP Standards for Petroleum and its Products, Part I, Vol 2.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
D97–11
3. Terminology
3.1 Definitions:
3.1.1 black oil, n—lubricant containing asphaltic materials. Black oils are used in heavy-duty equipment applications, such as
mining and quarrying, where extra adhesiveness is desired.
3.1.2 cylinder stock, n—lubricant for independently lubricated engine cylinders, such as those of steam engines and air
compressors. Cylinder stock are also used for lubrication of valves and other element
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.