ASTM B888/B888M-13
(Specification)Standard Specification for Copper Alloy Strip for Use in Manufacture of Electrical Connectors or Spring Contacts
Standard Specification for Copper Alloy Strip for Use in Manufacture of Electrical Connectors or Spring Contacts
SCOPE
1.1 This specification establishes the requirements for copper alloy strip for use in the manufacture of electrical connectors or spring contacts produced from one of the following Copper Alloy UNS Nos.2: C14530, C15100, C15500, C17000, C17200, C17410, C17450, C17460, C17500, C17510, C19002, C19010, C19015, C19025, C19210, C19400, C19500, C19700, C23000, C26000, C40810, C40850, C40860, C42200, C42500, C42520, C42600, C50580, C50780, C51000, C51080, C51100, C51180, C51980, C52100, C52180, C52480, C63800, C64725, C65400, C68800, C70250, C70260, C70265, C70310, C75200, and C76200.
1.2 The requirements for the other copper alloys such as copper-nickel-tin spinodal, UNS C72650, C72700, and C72900, shall be as prescribed in the current edition of Specification B740.
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:B888/B888M −13
Standard Specification for
Copper Alloy Strip for Use in Manufacture of Electrical
1
Connectors or Spring Contacts
This standard is issued under the fixed designation B888/B888M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled
Bar
1.1 This specification establishes the requirements for cop-
B248MSpecificationforGeneralRequirementsforWrought
per alloy strip for use in the manufacture of electrical connec-
Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled
tors or spring contacts produced from one of the following
2 Bar (Metric)
CopperAlloy UNS Nos. : C14530, C15100, C15500, C17000,
B601ClassificationforTemperDesignationsforCopperand
C17200, C17410, C17450, C17460, C17500, C17510,
Copper Alloys—Wrought and Cast
C19002, C19010, C19015, C19025, C19210, C19400,
B740Specification for Copper-Nickel-Tin Spinodal Alloy
C19500, C19700, C23000, C26000, C40810, C40850,
Strip
C40860, C42200, C42500, C42520, C42600, C50580,
B820Test Method for BendTest for Determining the Form-
C50780,C51000,C51080,C51100,C51180,C51980,C52100,
ability of Copper and Copper Alloy Strip
C52180, C52480, C63800, C64725, C65400, C68800,
B846Terminology for Copper and Copper Alloys
C70250, C70260, C70265, C70310, C75200, and C76200.
E8/E8MTest Methods for Tension Testing of Metallic Ma-
1.2 The requirements for the other copper alloys such as
terials
copper-nickel-tin spinodal, UNS C72650, C72700, and
E54Test Methods for ChemicalAnalysis of Special Brasses
4
C72900, shall be as prescribed in the current edition of
and Bronzes (Withdrawn 2002)
Specification B740.
E62Test Methods for Chemical Analysis of Copper and
4
CopperAlloys(PhotometricMethods)(Withdrawn2010)
1.3 The values stated in either SI units or inch-pound units
are to be regarded separately as standard. The values stated in E75Test Methods for Chemical Analysis of Copper-Nickel
4
and Copper-Nickel-Zinc Alloys (Withdrawn 2010)
each system may not be exact equivalents; therefore, each
system shall be used independently of the other. Combining E478Test Methods for ChemicalAnalysis of CopperAlloys
values from the two systems may result in non-conformance E527Practice for Numbering Metals and Alloys in the
Unified Numbering System (UNS)
with the standard.
5
2.2 ISO Standards:
2. Referenced Documents ISO 4744Copper and Copper Alloys—Determination of
3 Chromium Content—Flame Atomic Absorption Spectro-
2.1 ASTM Standards:
metric Method
B193Test Method for Resistivity of Electrical Conductor
ISO 7602Copper and Copper Alloys—Determination of
Materials
Tellurium Content
B248Specification for General Requirements for Wrought
3. Terminology
3.1 Definitions—For definition of terms used in this
1
This specification is under the jurisdiction of Committee B05 on Copper and
specification, refer to Terminology B846.
Copper Alloys and is the direct responsibility of Subcommittee B05.01 on Plate,
Sheet, and Strip.
4. General Requirements
Current edition approved Oct. 1, 2013. Published November 2013. Originally
approved in 1998. Last previous edition approved in 2012 as B888–12. DOI:
4.1 ForproductfurnishedunderthisspecificationinEnglish
10.1520/B0888_B0888M-13.
units, the following sections of Specification B248 must
2
The UNS system for copper and copper alloys (see Practice E527) is a simple
constitute a part of this specification. For product furnished
expansion of the former standard designation system accomplished by the addition
of a prefix “c” and a suffix “00.” The suffix can be used to accommodate
composition variations of the base alloy.
3 4
For referenced ASTM standards, visit the ASTM website, www.astm.org, or The last approved version of this historical standard is referenced on
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM www.astm.org.
5
Standards volume information, refer to the standard’s Document Summary page on Available fromAmerican National Standards Institute (ANSI), 25 W. 43rd St.,
the ASTM website. 4th Floor, New York, NY 10036, http://www.ansi.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
B888/B888M−13
under this specification in the SI units, the following sections 7.2 Manufacture—The product shall be produced by either
of Specification B248M must constitute a part of this specifi- hot- or cold-working operation. It shall be finished, unless
cation. otherwise specified,
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: B888 − 12 B888/B888M − 13
Standard Specification for
Copper Alloy Strip for Use in Manufacture of Electrical
1
Connectors or Spring Contacts
This standard is issued under the fixed designation B888;B888/B888M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification establishes the requirements for copper alloy strip for use in the manufacture of electrical connectors or
2
spring contacts produced from one of the following Copper Alloy UNS Nos. : C14530, C15100, C15500, C17000, C17200,
C17410, C17450, C17460, C17500, C17510, C19002, C19010, C19015, C19025, C19210, C19400, C19500, C19700, C23000,
C26000, C40810, C40850, C40860, C42200, C42500, C42520, C42600, C50580, C50780, C51000, C51080, C51100, C51180,
C51980, C52100, C52180, C52480, C63800, C64725, C65400, C68800, C70250, C70260, C70265, C70310, C75200, and
C76200.
1.2 The requirements for the other copper alloys such as copper-nickel-tin spinodal, UNS C72650, C72700, and C72900, shall
be as prescribed in the current edition of Specification B740.
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each
system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the
two systems may result in non-conformance with the standard.
2. Referenced Documents
3
2.1 ASTM Standards:
B193 Test Method for Resistivity of Electrical Conductor Materials
B248 Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar
B248M Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar
(Metric)
B601 Classification for Temper Designations for Copper and Copper Alloys—Wrought and Cast
B740 Specification for Copper-Nickel-Tin Spinodal Alloy Strip
B820 Test Method for Bend Test for Determining the Formability of Copper and Copper Alloy Strip
B846 Terminology for Copper and Copper Alloys
E8E8/E8M Test Methods for Tension Testing of Metallic Materials
4
E8M Test Methods for Tension Testing of Metallic Materials [Metric] (Withdrawn 2008)
4
E54 Test Methods for Chemical Analysis of Special Brasses and Bronzes (Withdrawn 2002)
4
E62 Test Methods for Chemical Analysis of Copper and Copper Alloys (Photometric Methods) (Withdrawn 2010)
4
E75 Test Methods for Chemical Analysis of Copper-Nickel and Copper-Nickel-Zinc Alloys (Withdrawn 2010)
E478 Test Methods for Chemical Analysis of Copper Alloys
E527 Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)
5
2.2 ISO Standards:
ISO 4744 Copper and Copper Alloys—Determination of Chromium Content—Flame Atomic Absorption Spectrometric Method
ISO 7602 Copper and Copper Alloys—Determination of Tellurium Content
1
This specification is under the jurisdiction of Committee B05 on Copper and Copper Alloys and is the direct responsibility of Subcommittee B05.01 on Plate, Sheet, and
Strip.
Current edition approved Oct. 1, 2012Oct. 1, 2013. Published November 2012November 2013. Originally approved in 1998. Last previous edition approved in 20102012
as B888 – 10.B888 – 12. DOI: 10.1520/B0888-12.10.1520/B0888_B0888M-13.
2
The UNS system for copper and copper alloys (see Practice E527) is a simple expansion of the former standard designation system accomplished by the addition of a
prefix “c” and a suffix “00.” The suffix can be used to accommodate composition variations of the base alloy.
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
4
The last approved version of this historical standard is referenced on www.astm.org.
5
Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
B888/B888M − 13
3. Terminology
3.1 Definitions—For definition of terms used in this specification, refer to Te
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.