ASTM C1002-07
(Specification)Standard Specification for Steel Self-Piercing Tapping Screws for the Application of Gypsum Panel Products or Metal Plaster Bases to Wood Studs or Steel Studs
Standard Specification for Steel Self-Piercing Tapping Screws for the Application of Gypsum Panel Products or Metal Plaster Bases to Wood Studs or Steel Studs
ABSTRACT
This specification covers steel self-piercing tapping screws for use in fastening gypsum panel products and metal plaster bases to cold-formed steel studs and wood members and for fastening gypsum panel products to gypsum board. Steel screws covered by this specification are of four types of thread configurations: (1) Type G, course-pitch high-thread self-piercing screws for fastening gypsum board to gypsum board; (2) Type S, fine-thread screw for fastening gypsum board to cold formed steel members; (3) Type W, course-thread screw for fastening gypsum board to wood members; and (4) Type A, course-pitch tapping screw thread for fastening metal plaster bases to wood or cold-formed steel. All these steel screw types shall be tested for the determination of performance requirements and physical properties (hardness and ductility) covered in this specification. For the appearance of screws, the form shall be straight and neatly formed, and the threads shall be clean and smooth. Screws shall also have a corrosion-resistant treatment which shall not inhibit adhesion to finishing compounds nor bleed through field-applied decoration.
SCOPE
1.1 This specification covers steel self-piercing tapping screws for use in fastening gypsum panel products and metal plaster bases to cold-formed steel studs less than 0.033 in. (0.84 mm) in thickness and wood members and for fastening gypsum panel products to gypsum board.
1.2 This specification also covers test methods for determining performance requirements and physical properties.
1.3 The values stated in inch-pound units are to be regarded as the standard. The SI (metric) values given in parentheses are approximate and are for information only. The following safety hazards caveat pertains only to the test methods described in this specification:
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:C1002 −07
StandardSpecification for
Steel Self-Piercing Tapping Screws for the Application of
Gypsum Panel Products or Metal Plaster Bases to Wood
1
Studs or Steel Studs
This standard is issued under the fixed designation C1002; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope* C11 Terminology Relating to Gypsum and Related Building
Materials and Systems
1.1 This specification covers steel self-piercing tapping
C1396/C1396M Specification for Gypsum Board
screws for use in fastening gypsum panel products and metal
C645 Specification for Nonstructural Steel Framing Mem-
plaster bases to cold-formed steel studs less than 0.033 in.
bers
(0.84 mm) in thickness and wood members and for fastening
C847 Specification for Metal Lath
gypsum panel products to gypsum board.
1.2 Thisspecificationalsocoverstestmethodsfordetermin-
3. Terminology
ing performance requirements and physical properties.
3.1 Definitions:For definitions relating to gypsum and re-
1.3 The values stated in inch-pound units are to be regarded
lated building materials and systems, see Terminology C11.
as the standard.The SI (metric) values given in parentheses are
3.2 Definitions of Terms Specific to This Standard:
approximate and are for information only.
3.2.1 self-piercing, v—the ability to penetrate without ben-
1.4 The following safety hazards caveat pertains only to the
efit of a pre-drilled hole with sharp-point angles of not more
test methods described in this specification: This standard does
than 30°.
not purport to address all of the safety concerns, if any,
3.2.2 spin-out, v—for a screw, the continued rotation of a
associated with its use. It is the responsibility of the user of this
screw without further penetration into the substrate.
standard to establish appropriate safety and health practices
and determine the applicability of regulatory limitations prior
4. Classification
to use.
4.1 Steel screws covered by this specification are of four
2. Referenced Documents types of thread configurations:
2
4.1.1 Type G, course-pitch high-thread self-piercing screws
2.1 ASTM Standards:
for fastening gypsum board to gypsum board.
A548 Specification for Steel Wire, Carbon, Cold-Heading
4.1.2 Type S, fine-thread screw for fastening gypsum board
Quality, for Tapping or Sheet Metal Screws (Withdrawn
3
to cold formed steel members.
1989)
4.1.3 Type W, course-thread screw for fastening gypsum
A568/A568M Specification for Steel, Sheet, Carbon,
board to wood members.
Structural,andHigh-Strength,Low-Alloy,Hot-Rolledand
4.1.4 Type A, course-pitch tapping screw thread for fasten-
Cold-Rolled, General Requirements for
ing metal plaster bases to wood or cold-formed steel.
1
This specification is under the jurisdiction of ASTM Committee C11 on
5. Materials
Gypsum and Related Building Materials and Systems and is the direct responsibility
of Subcommittee C11.02 on Specifications and Test Methods for Accessories and
5.1 Steel Wire, for manufacturing screws, Specification
Related Products.
A548, Grades 1013 to 1022 for Type G and Type W screws.
Current edition approved Aug. 1, 2007. Published August 2007. Originally
approved in 1983. Last previous edition approved in 2004 as C1002 – 04. DOI:
5.2 Steel Wire, for manufacturing screws, Specification
10.1520/C1002-07.
A568/A568M, Grades 1018 to 1022 for Type S and Type A
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
screws.
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
6. Physical Properties
3
The last approved version of this historical standard is referenced on
www.astm.org. 6.1 Hardness:
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C1002−07
6.1.1 The surface of Type S, Type W, and Type A screws 8.2.2 Screws for Fastening Metal Plaster Bases—The top of
shall be case hardened to a depth of not less than 0.002 in. the screw shall be either flat or contoured.The underside of the
(0.05 mm) with case hardness not less than 45 HRC. head shall be flat or near flat. The threads shall extend to the
6.1.2 The surface of Type G screws is not required to be underside of the head.
case hardened.
8.3 Driving Recess:
6.2 Ductility—The screws shall have sufficient ductility to 8.3.1 Screws for Fastenin
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:C1002–04 Designation: C 1002 – 07
Standard Specification for
Steel Self-Piercing Tapping Screws for the Application of
Gypsum Panel Products or Metal Plaster Bases to Wood
1
Studs or Steel Studs
This standard is issued under the fixed designation C 1002; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope*
1.1 This specification covers steel self-piercing tapping screws for use in fastening gypsum panel products and metal plaster
bases to cold-formed steel studs less than 0.033 in. (0.84 mm) in thickness and wood members and for fastening gypsum panel
products to gypsum board.
1.2 This specification also covers test methods for determining performance requirements and physical properties.
1.3 The values stated in inch-pound units are to be regarded as the standard. The SI (metric) values given in parentheses are
approximate and are for information only.
1.4 The following safety hazards caveat pertains only to the test methods described in this specification: This standard does not
purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to
establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
A 548 NO TITLE
3
Specification for Steel Wire, Carbon, Cold-Heading Quality for Tapping or Sheet Metal Screws
A 568/A 568M Specification for Steel, Sheet, Carbon, Structural, and High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled,
General Requirements for
C11 Terminology Relating to Gypsum and Related Building Materials and Systems
C 1396/C 1396M Specification for Gypsum Board
C36/C36MSpecification for Gypsum Wallboard
C 645 Specification for Nonstructural Steel Framing Members
C 847 Specification for Metal Lath
3. Terminology
3.1 Definitions: For definitions relating to gypsum and related building materials and systems, see Terminology C 11.
3.2 Definitions of Terms Specific to This Standard:
3.2.1 self-piercing, v—the ability to penetrate without benefit of a pre-drilled hole with sharp-point angles of not more than 30°.
3.2.2 spin-out, v—for a screw, the continued rotation of a screw without further penetration into the substrate.
4. Classification
4.1 Steel screws covered by this specification are of four types of thread configurations:
4.1.1 Type G, course-pitch high-thread self-piercing screws for fastening gypsum board to gypsum board.
4.1.2 Type S, fine-thread screw for fastening gypsum board to cold formed steel members.
4.1.3 Type W, course-thread screw for fastening gypsum board to wood members.
4.1.4 Type A, course-pitch tapping screw thread for fastening metal plaster bases to wood or cold-formed steel.
1
This specification is under the jurisdiction of ASTM Committee C11 on Gypsum and Related Building Materials and Systems and is the direct responsibility of
Subcommittee C11.02 on Specifications and Test Methods for Accessories and Related Products.
Current edition approved Oct.Aug. 1, 2004.2007. Published October 2004.August 2007. Originally approved in 1983. Last previous edition approved in 20012004 as
C 1002 – 014.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Withdrawn
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
C1002–07
5. Materials
5.1 Steel Wire, for manufacturing screws, Specification A 548, Grades 1013 to 1022 for Type G and Type W screws.
5.2 Steel Wire, for manufacturing screws, Specification A 568/A 568M, Grades 1018 to 1022 for Type S and Type A screws.
6. Physical Properties
6.1 Hardness:
6.1.1 The surface of Type S, Type W, and TypeAscrews shall be case hardened to a depth of not less than 0.002 in. (0.05 mm)
with case hardness not less than 45 HRC.
6.1.2 The surface of Type G screws is not required to be case hardened.
6.2 Ductility—Thescrewsshallhaves
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.