ASTM B670-07
(Specification)Standard Specification for Precipitation-Hardening Nickel Alloy (UNS N07718) Plate, Sheet, and Strip for High-Temperature Service
Standard Specification for Precipitation-Hardening Nickel Alloy (UNS N07718) Plate, Sheet, and Strip for High-Temperature Service
ABSTRACT
This specification covers rolled precipitation hardening nickel alloy (UNS N07718) plate, sheet, and strip in the annealed condition (temper) for high-temperature service. The material shall conform to the chemical requirements for carbon, manganese, silicon, phosphorus, sulfur, chromium, cobalt, molybdenum, columbium, niobium, tantalum, titanium, aluminum, iron, copper, nickel, and boron. The material after precipitation hardening shall conform to the mechanical property requirements for tensile strength, yield strength, and elongation. Stress-rupture test shall be performed in accordance to referenced ASTM documents itemized herein.
SCOPE
1.1 This specification covers rolled precipitation hardenable nickel alloy (N07718)* plate, sheet, and strip in the annealed condition (temper).
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:B670 −07
StandardSpecification for
Precipitation-Hardening Nickel Alloy (UNS N07718) Plate,
1
Sheet, and Strip for High-Temperature Service
This standard is issued under the fixed designation B670; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope 3. Terminology
3.1 Description of Terms Specific to This Standard—The
1.1 This specification covers rolled precipitation hardenable
terms given in Table 1 shall apply.
nickel alloy (N07718)* plate, sheet, and strip in the annealed
condition (temper).
4. General Requirements
1.2 The values stated in inch-pound units are to be regarded
4.1 Material furnished under this specification shall con-
as the standard. The values given in parentheses are for
form to the applicable requirements of Specification B906
information only.
unless otherwise provided herein.
1.3 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the
5. Ordering Information
responsibility of the user of this standard to become familiar
5.1 It is the responsibility of the purchaser to specify all
with all hazards including those identified in the appropriate
requirements that are necessary for material ordered to this
Material Safety Data Sheet (MSDS) for this product/material
specification. Examples of such requirements include, but are
as provided by the manufacturer, to establish appropriate
not limited to, the following:
safety and health practices, and determine the applicability of
5.1.1 Alloy—Name or UNS number (see Table 2).
regulatory limitations prior to use.
5.1.2 ASTM designation, including year of issue.
5.1.3 Condition—See 7.1 and Appendix X1.
2. Referenced Documents
5.1.4 Finish—Specification B906 or Appendix X1.
2
5.1.5 Dimensions—Thickness, width, and length.
2.1 ASTM Standards:
5.1.6 Quantity:
B637 Specification for Precipitation-Hardening and Cold
5.1.7 Optional Requirements:
Worked Nickel Alloy Bars, Forgings, and Forging Stock
5.1.7.1 Sheet and Strip—Whether to be furnished in coil, in
for Moderate or High Temperature Service
cut straight lengths, or in random straight lengths.
B906 Specification for General Requirements for Flat-
5.1.7.2 Strip—Whether to be furnished with commercial slit
Rolled Nickel and Nickel Alloys Plate, Sheet, and Strip
edge, square edge, or round edge.
E29 Practice for Using Significant Digits in Test Data to
5.1.7.3 Plate—Whether to be furnished specially flattened
Determine Conformance with Specifications
(see 8.7); also how plate is to be cut (see 8.2.1 and 8.3.2).
E139 Test Methods for Conducting Creep, Creep-Rupture,
5.1.8 Fabrication Details—Not mandatory but helpful to
and Stress-Rupture Tests of Metallic Materials
the manufacturer:
5.1.8.1 Welding or Brazing—Process to be employed.
5.1.8.2 Plate—Whether material is to be hot-formed.
1
This specification is under the jurisdiction of ASTM Committee B02 on
5.1.9 Certification—State if certification or a report of test
Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee
B02.07 on Refined Nickel and Cobalt and Their Alloys. results is required (see Specification B906).
Current edition approved Nov. 1, 2007. Published December 2007. Originally
5.1.10 Samples for Product (Check) Analysis—Whether
approved in 1972. Last previous edition approved in 2002 as B670 – 02. DOI:
samples should be furnished (see 6.2).
10.1520/B0670-07.
5.1.11 Purchaser Inspection—If the purchaser wishes to
* New designation established in accordance withASTM E527 and SAE J1086,
Practice for Numbering Metals and Alloys (UNS).
witness the tests or inspection of material at the place of
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
manufacture, the purchase order must so state indicating which
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
tests or inspections are to be witnessed (see Specification
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. B906).
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
B670−07
A
TABLE 1 Product Description TABLE 3 Tensile Properties for Plate, Sheet, and Strip
Yield Strength Elongation in 2
Product Thickness, in. (mm) Width
Tensile
Nominal Thickness, (0.2 % offset), in.or50mm
A
3 1
Hot-rolled plate ⁄16 to 2 ⁄4 (4.8 to 57.2) (B906, B906, Tables A3.2 Strength min,
in. (mm) min, ksi (or 4D),
B
Table A3.1) an
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:B670–02 Designation: B 670 – 07
Standard Specification for
Precipitation-Hardening Nickel Alloy (UNS N07718) Plate,
1
Sheet, and Strip for High-Temperature Service
This standard is issued under the fixed designation B 670; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope
1.1 This specification covers rolled precipitation hardenable nickel alloy (N07718)* plate, sheet, and strip in the annealed
condition (temper).
1.2 Thevaluesstatedininch-poundunitsaretoberegardedasthestandard.Thevaluesgiveninparenthesesareforinformation
only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data
Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and
determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
B 637 Specification for Precipitation-Hardening NickelAlloy Bars, Forgings, and Forging Stock for High-Temperature Service
B880Specification for General Requirements for Chemical CheckAnalysis Limits for Nickel, NickelAlloys and CobaltAlloys
906 Specification for General Requirements for Flat-Rolled Nickel and Nickel Alloys Plate, Sheet, and Strip
E8Test Methods for Tension Testing of Metallic Materials
E 29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
4
E 139Test Methods for Conducting Creep, Creep-Rupture, and Stress-Rupture Tests of Metallic Materials
E354TestMethodsforChemicalAnalysisofHigh-Temperature,Electrical,Magnetic,andOtherSimilarIron,Nickel,andCobalt
3
Alloys
3
E1473Test Methods for Chemical Analysis of Nickel, Cobalt, and High-Temperature Alloys Test Methods for Conducting
Creep, Creep-Rupture, and Stress-Rupture Tests of Metallic Materials
3. Terminology
3.1 Description of Terms Specific to This Standard—The terms given in Table 1 shall apply.
4. Ordering Information
4.1It is the responsibility of the purchaser to specify all requirements that are necessary for material ordered to this specification.
Examples of such requirements include, but are not limited to, the following:
4.1.1General Requirements
4.1 Material furnished under this specification shall conform to the applicable requirements of Specification B 906 unless
otherwise provided herein.
5. Ordering Information
5.1 It is the responsibility of the purchaser to specify all requirements that are necessary for material ordered to this
specification. Examples of such requirements include, but are not limited to, the following:
1
ThisspecificationisunderthejurisdictionofASTMCommitteeB02onNonferrousMetalsandAlloysandisthedirectresponsibilityofSubcommitteeB02.07onRefined
Nickel and Cobalt and Their Alloys.
Current edition approved May 10, 2002. Published July 2002. Originally published as A670–72. Redesignated B670 in 1978. Last previous edition B670–95.
Current edition approved Nov. 1, 2007. Published December 2007. Originally approved in 1972. Last previous edition approved in 2002 as B 670 – 02.
* New designation established in accordance with ASTM E 527 and SAE J1086, Practice for Numbering Metals and Alloys (UNS).
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
, Vol 02.04.volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
B670–07
TABLE 1 Product Description
Product Thickness, in. (mm) Width
A B
3 1
Hot-rolled plate ⁄16 to 2 ⁄4 (4.8 to 57.2) (Table 5) Tables 7 and 8
A
3 1
Hot-rolled plate ⁄16 to 2 ⁄4 (4.8 to 57.2) (B 906, B 906, Tables A3.2
B
Table A3.1) and A3.5
C
Cold-rolled sheet 0.010 to 0.250 (0.25 to 6.4), incl Table 9
(Table 6)
C
Cold-rolled sheet 0.010 to 0.250 (0.25 to 6.4), incl B 906 , Table A3.6
(, Table A3.3)
0.005 to 0.250 (0.13 to 6.4), incl
(Table 6)
0.005 to 0.250
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.