ASTM D1483-12
(Test Method)Standard Test Method for Oil Absorption of Pigments by Gardner-Coleman Method
Standard Test Method for Oil Absorption of Pigments by Gardner-Coleman Method
SIGNIFICANCE AND USE
The oil absorption value obtained by this test method provides information about the vehicle demand of the pigment when it is used in a pigment paste. Oil absorption values can be used to characterize batches of a given pigment.
This test method differs from Test Method D281 in that D281 requires a vigorous rubbing action whereas this test method involves only a gentle stirring and folding of the pigment. Because the end points are different, the values obtained from the two test methods generally differ.
SCOPE
1.1 This test method covers the determination of oil absorption of pigments by the Gardner-Coleman procedure.
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D1483 − 12
Standard Test Method for
1
Oil Absorption of Pigments by Gardner-Coleman Method
This standard is issued under the fixed designation D1483; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope* method involves only a gentle stirring and folding of the
pigment. Because the end points are different, the values
1.1 This test method covers the determination of oil absorp-
2 obtained from the two test methods generally differ.
tion of pigments by the Gardner-Coleman procedure.
5. Apparatus and Materials
1.2 The values stated in SI units are to be regarded as the
standard. The values given in parentheses are for information
5.1 Balance, capable of weighing to 0.01 g.
only.
5.2 Glass Container, round-bottom, having a capacity of
1.3 This standard does not purport to address all of the
1
250 mL ( ⁄2 pt), or a low-form 250-mL beaker.
safety concerns, if any, associated with its use. It is the
5.3 Buret, graduated in 0.1-mL divisions.
responsibility of the user of this standard to establish appro-
priate safety and health practices and determine the applica- 5.4 Spatula, sharp-edged steel, having a blade 15 or 20 by
1 3
bility of regulatory limitations prior to use. 100 mm ( ⁄2 or ⁄4 by 4 in.).
5.5 Linseed Oil, raw, conforming to the following specifi-
2. Referenced Documents
cation:
3
2.1 ASTM Standards:
Specific Gravity 0.926 – 0.931
D281Test Method for Oil Absorption of Pigments by
Boiling Point >149°C
Spatula Rub-out Acid Number 3 ± 1
Saponification Value 185 – 196
Iodine Value 170 minimum
3. Summary of Test Method
Gardner Color 13 maximum
3.1 A soft paste is formed by the dropwise addition of
6. Procedure
linseed oil to the gently stirred pigment. The amount of oil
6.1 The weight of pigment used should correspond to a
required to form the paste is used to calculate an oil absorption
value. pigment volume of 3.0 6 0.6 mL. Determine the weight
needed by multiplying 3.0 6 0.6 mLby the specific gravity of
4. Significance and Use
the pigment being tested. For example, a 20 g specimen
normally is used for zinc oxide (3.6 mL×5.6 g/mL=20.2 g).
4.1 The oil absorption value obtained by this test method
provides information about the vehicle demand of the pigment Transfer the amount, weighed to 0.01 g, to the glass container.
whenitisusedinapigmentpaste.Oilabsorptionvaluescanbe
6.2 Add oil from the buret at the rate of about 1 drop per
used to characterize batches of a given pigment.
second, stirring and “folding” the pigment continuously with
the spatula during the addition. Try to provide dry pigment for
4.2 This test method differs from Test Method D281 in that
D281 requires a vigorous rubbing action whereas this test theoiltostrike.Donotruborgrind;astheparticlesofpigment
become wetted, they collect in small lumps that gradually
coalesce. As the coalescence proceeds, reduce the rate of oil
1
This test method is under the jurisdiction of ASTM Committee D01 on Paint
addition by at least half. The end point is reached when the
and Related Coatings, Materials, andApplications and is the direct responsibility of
Subcommittee D01.24 on Physical Properties of Liquid Paints & Paint Materials.
lumps, with a rolling action from the spatula, collect into a
Current edition approved Feb. 1, 2012. Published February 2012. Originally
single ball or the excess of oil smears the wall of the container.
approved in 1957. Last previous edition approved in 2007 as D1483–95(2007).
DOI: 10.1520/D1483-12.
7. Calculation
2
See Gardner, H. A. and Coleman, R. E., “Oil Absorption of Pigments,”
Scientific Section Circular 85, Paint Manufacturers’ Assoc. of the United States,
7.1 Calculate the oil absorption, A, as follows:
February 1920.
3
M 30.93
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
A 5 3100 (1)
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
P
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D1483 − 12
where: at 20 df. Based on these coefficients, the following criteria
should be used to judge the acceptability of results at the 95%
M = oil, mL, and
confidence level:
P = pigment, g.
9.1.1 Repeatability—Two results obtained by the same op-
0.93 represents density of oil (in grams per millilitr
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:D1483–95(Reapproved2007) Designation:D1483–12
Standard Test Method for
1
Oil Absorption of Pigments by Gardner-Coleman Method
This standard is issued under the fixed designation D1483; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope*
2
1.1 This test method covers the determination of oil absorption of pigments by the Gardner-Coleman procedure.
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2.1 ASTM Standards:
3
D234Specification for Raw Linseed Oil ASTM Standards:
D281 Test Method for Oil Absorption of Pigments by Spatula Rub-out
3. Summary of Test Method
3.1 A soft paste is formed by the dropwise addition of linseed oil to the gently stirred pigment. The amount of oil required to
form the paste is used to calculate an oil absorption value.
4. Significance and Use
4.1 The oil absorption value obtained by this test method provides information about the vehicle demand of the pigment when
it is used in a pigment paste. Oil absorption values can be used to characterize batches of a given pigment.
4.2 This test method differs from Test Method D281 in that D281 requires a vigorous rubbing action whereas this test method
involves only a gentle stirring and folding of the pigment. Because the end points are different, the values obtained from the two
test methods generally differ.
5. Apparatus and Materials
5.1 Balance, capable of weighing to 0.01 g.
1
5.2 Glass Container, round-bottom, having a capacity of 250 mL ( ⁄2 pt), or a low-form 250-mL beaker.
5.3 Buret, graduated in 0.1-mL divisions.
1 3
5.4 Spatula, sharp-edged steel, having a blade 15 or 20 by 100 mm ( ⁄2 or ⁄4 by 4 in.).
5.5 Linseed Oil, Raw, conforming to Specification D234 except that it shall have an acid number of 3 6 1. , raw, conforming
to the following specification:
Specific Gravity 0.926 – 0.931
Boiling Point >149°C
Acid Number 3 6 1
Saponification Value 185 – 196
Iodine Value 170 minimum
Gardner Color 13 maximum
6. Procedure
6.1 The weight of pigment used should correspond to a pigment volume of 3.0 6 0.6 mL. Determine the weight needed by
1
This test method is under the jurisdiction of ASTM Committee D01 on Paint and Related Coatings, Materials, and Applications and is the direct responsibility of
Subcommittee D01.24 on Physical Properties of Liquid Paints and& Paint Materials.
Current edition approved JulyFeb. 1, 2007.2012. Published July 2007.February 2012. Originally approved in 1957. Last previous edition approved in 20022007 as
D1483 – 95 (20027). DOI: 10.1520/D1483-95R07.10.1520/D1483-12.
2
See Gardner, H.A. and Coleman, R. E., “OilAbsorption of Pigments,” Scientific Section Circular 85, Paint Manufacturers’Assoc. of the United States, February 1920.
3
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
D1483–12
multiplying 3.0 6 0.6 mL by the specific gravity of the pigment being tested. For example, a 20 g specimen normally is used for
zinc oxide (3.6 mL 3 5.6 g/mL = 20.2 g). Transfer the amount, weighed to 0.01 g, to the glass container.
6.2 Add oil from the buret at the rate of about 1 drop per second, stirring and “folding” the pigment continuously with the
spatula during the addition.Try to provide dry pigment for the oil to strike. Do not rub or grind; as the particles of pigment become
wetted, they collect in small lumps that gradually coalesce.As the coalescence proceeds, reduce the rate of oil addition by at least
half. The end point is reach
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.