ASTM A490-10
(Specification)Standard Specification for Structural Bolts, Alloy Steel, Heat Treated, 150 ksi Minimum Tensile Strength
Standard Specification for Structural Bolts, Alloy Steel, Heat Treated, 150 ksi Minimum Tensile Strength
SCOPE
1.1 This specification covers two types of quenched and tempered, alloy steel, heavy hex structural bolts having a tensile strength of 150 to 173 ksi.
1.2 These bolts are intended for use in structural connections. These connections are covered under the requirements of the Specification for Structural Joints Using Specification A325 or A490 bolts, approved by the Research Council on Structural Connections; endorsed by the American Institute of Steel Construction and by the Industrial Fastener Institute.
1.3 The bolts are furnished in sizes ½ to 1½ in., inclusive. They are designated by type denoting chemical composition as follows:
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
American Association State
Designation: A490 – 10 Highway and Transportation
Officials Standard
AASHTO No.: M 253
Standard Specification for
Structural Bolts, Alloy Steel, Heat Treated, 150 ksi Minimum
1
Tensile Strength
This standard is issued under the fixed designation A490; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope* of this standard to establish appropriate safety and health
practices and determine the applicability of regulatory limita-
1.1 This specification covers two types of quenched and
tions prior to use.
tempered, alloy steel, heavy hex structural bolts having a
tensile strength of 150 to 173 ksi.
2. Referenced Documents
1.2 These bolts are intended for use in structural connec-
3
2.1 ASTM Standards:
tions.These connections are covered under the requirements of
A194/A194M Specification for Carbon and Alloy Steel
theSpecificationforStructuralJointsUsingSpecificationA325
Nuts for Bolts for High Pressure or High Temperature
orA490 bolts, approved by the Research Council on Structural
Service, or Both
Connections; endorsed by the American Institute of Steel
2 A325 SpecificationforStructuralBolts,Steel,HeatTreated,
Construction and by the Industrial Fastener Institute.
120/105 ksi Minimum Tensile Strength
1 1
1.3 The bolts are furnished in sizes ⁄2 to 1 ⁄2 in., inclusive.
A354 SpecificationforQuenchedandTemperedAlloySteel
They are designated by type denoting chemical composition as
Bolts, Studs, and Other Externally Threaded Fasteners
follows:
A490M SpecificationforHigh-StrengthSteelBolts,Classes
Type Description
10.9 and 10.9.3, for Structural Steel Joints (Metric)
Type 1 Medium carbon alloy steel
A563 Specification for Carbon and Alloy Steel Nuts
Type 2 Withdrawn in 2002
A751 Test Methods, Practices, andTerminology for Chemi-
Type 3 Weathering steel
cal Analysis of Steel Products
1.4 This specification provides that heavy hex structural
D3951 Practice for Commercial Packaging
bolts shall be furnished unless other dimensional requirements
E384 Test Method for Knoop and Vickers Hardness of
are specified on the purchase order.
Materials
1.5 Terms used in this specification are defined in Termi-
E709 Guide for Magnetic Particle Testing
nology F1789 unless otherwise defined herein.
E1444 Practice for Magnetic Particle Testing
1.6 For metric bolts, see SpecificationA490M Classes 10.9
F436 Specification for Hardened Steel Washers
and 10.9.3
F606 Test Methods for Determining the Mechanical Prop-
1.7 The values stated in inch-pound units are to be regarded
erties of Externally and Internally Threaded Fasteners,
as standard. No other units of measurement are included in this
Washers, Direct Tension Indicators, and Rivets
standard.
F788/F788M Specification for Surface Discontinuities of
1.8 The following safety hazards caveat pertains only to the
Bolts, Screws, and Studs, Inch and Metric Series
Test Methods portion, Section 12 of this specification: This
F959 Specification for Compressible-Washer-Type Direct
standard does not purport to address all of the safety concerns,
Tension Indicators for Use with Structural Fasteners
if any, associated with its use. It is the responsibility of the user
F1136 Specification for Zinc/Aluminum Corrosion Protec-
tive Coatings for Fasteners
F1470 Practice for Fastener Sampling for Specified Me-
1 chanical Properties and Performance Inspection
This specification is under the jurisdiction of ASTM Committee F16 on
Fasteners and is the direct responsibility of Subcommittee F16.02 on Steel Bolts,
Nuts, Rivets and Washers.
Current edition approved May 1, 2010. Published June 2010. Originally
3
approved in 1964. Last previous edition approved in 2009 as A490 – 09. DOI: For referenced ASTM standards, visit the ASTM website, www.astm.org, or
10.1520/A0490-10. contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
2
Available from American Institute of Steel Construction (AISC), One E. Standards volume information, refer to the standard’s Document Summary page on
Wacker Dr., Suite 700, Chicago, IL 60601-2001, http://www.aisc.org. the ASTM website.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
A490 – 10
F1789 Terminology for F16 Mechanical Fasteners 3.2.2 Alternatively, nuts conforming to Specification A194/
F2328 Test Method for Determining Decarburization and A194M Gr. 2H plain (uncoated)
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
American Association State
Designation:A490–09 Designation: A490 – 10 Highway and Transportation
Officials Standard
AASHTO No.: M 253
Standard Specification for
Structural Bolts, Alloy Steel, Heat Treated, 150 ksi Minimum
1
Tensile Strength
This standard is issued under the fixed designation A490; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope*
1.1 This specification covers two types of quenched and tempered, alloy steel, heavy hex structural bolts having a tensile
strength of 150 to 173 ksi.
1.2 These bolts are intended for use in structural connections. These connections are covered under the requirements of the
Specification for Structural Joints Using Specification A325 or A490 bolts, approved by the Research Council on Structural
2
Connections; endorsed by the American Institute of Steel Construction and by the Industrial Fastener Institute.
1 1
1.3 The bolts are furnished in sizes ⁄2 to 1 ⁄2 in., inclusive. They are designated by type denoting chemical composition as
follows:
Type Description
Type 1 Medium carbon alloy steel
Type 2 Withdrawn in 2002
Type 3 Weathering steel
1.4 This specification provides that heavy hex structural bolts shall be furnished unless other dimensional requirements are
specified on the purchase order.
1.5 Terms used in this specification are defined in Terminology F1789 unless otherwise defined herein.
1.6 For metric bolts, see Specification A490M Classes 10.9 and 10.9.3
1.7 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this
standard.
1.8 ThefollowingsafetyhazardscaveatpertainsonlytotheTestMethodsportion,Section12ofthisspecification: This standard
does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this
standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
3
2.1 ASTM Standards:
A194/A194M Specification for Carbon andAlloy Steel Nuts for Bolts for High Pressure or High Temperature Service, or Both
A325 Specification for Structural Bolts, Steel, Heat Treated, 120/105 ksi Minimum Tensile Strength
A354 Specification for Quenched and Tempered Alloy Steel Bolts, Studs, and Other Externally Threaded Fasteners
A490M Specification for High-Strength Steel Bolts, Classes 10.9 and 10.9.3, for Structural Steel Joints (Metric)
A563 Specification for Carbon and Alloy Steel Nuts
A751 Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products
D3951 Practice for Commercial Packaging
E384 Test Method for Knoop and Vickers Hardness of Materials
E709 Guide for Magnetic Particle Testing
E1444 Practice for Magnetic Particle Testing
F436 Specification for Hardened Steel Washers
1
This specification is under the jurisdiction of ASTM Committee F16 on Fasteners and is the direct responsibility of Subcommittee F16.02 on Steel Bolts, Nuts, Rivets
and Washers.
Current edition approved Nov.May 1, 2009.2010. Published November 2009.June 2010. Originally approved in 1964. Last previous edition approved in 20082009 as
A490–08b.A490 – 09. DOI: 10.1520/A0490-109.
2
Available from American Institute of Steel Construction (AISC), One E. Wacker Dr., Suite 700, Chicago, IL 60601-2001, http://www.aisc.org.
3
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
A490 – 10
F606 TestMethodsforDeterminingtheMechanicalPropertiesofExternallyandInternallyThreadedFasteners,Washers,Direct
Tension Indicators, and Rivets
F788/F788M Specification for Surface Discontinuities of Bolts, Screws, and Studs, Inch and Metric Series
F959 Specification for Compressible-Washer-Type Direct Tension Indicators for Use with Structural Fasteners
F1136 Specification for Zinc/Aluminum Corrosion Protecti
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.