ASTM B789/B789M-16(2021)
(Practice)Standard Practice for Installing Corrugated Aluminum Structural Plate Pipe for Culverts and Sewers
Standard Practice for Installing Corrugated Aluminum Structural Plate Pipe for Culverts and Sewers
SIGNIFICANCE AND USE
4.1 Corrugated aluminum structural plate pipe functions structurally as a flexible ring that is supported by and interacts with the compacted surrounding soil. The soil placed around the structure is thus an integral part of the structural system. It is therefore important to ensure that the soil structure is made up of the acceptable material and well-constructed. Field verification of soil structure acceptability using Test Methods D1556/D1556M, D2167, D6938, or D2937, as applicable, and comparing the results with Test Methods D698 or D1557, in accordance with the specifications for each project, is the most reliable basis for installation of an acceptable structure. The required density and method of measurement are not specified by this practice but must be established in the specifications for each project.
SCOPE
1.1 This practice covers procedures, soils, and soil placement for the proper installation of corrugated aluminum structural plate culverts and sewers in either trench or embankment installations. A typical trench installation is shown in Fig. 1, and a typical embankment (projection) installation is shown in Fig. 2. Structural plate structures as described herein are those structures factory fabricated in plate form and bolted together on site to provide the required shape, size, and length of structure. This practice applies to structures designed in accordance with Practice B790/B790M.
FIG. 1 Typical Trench Installation
FIG. 2 Typical Embankment (Projection) Installation
1.2 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: B789/B789M − 16 (Reapproved 2021)
Standard Practice for
Installing Corrugated Aluminum Structural Plate Pipe for
Culverts and Sewers
This standard is issued under the fixed designation B789/B789M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope Structural Plate for Field-Bolted Pipe, Pipe-Arches, and
Arches
1.1 This practice covers procedures, soils, and soil place-
B790/B790M Practice for Structural Design of Corrugated
ment for the proper installation of corrugated aluminum
Aluminum Pipe, Pipe-Arches, and Arches for Culverts,
structural plate culverts and sewers in either trench or embank-
Storm Sewers, and Other Buried Conduits
ment installations.Atypical trench installation is shown in Fig.
D698 Test Methods for Laboratory Compaction Character-
1, and a typical embankment (projection) installation is shown
istics of Soil Using Standard Effort (12,400 ft-lbf/ft (600
in Fig. 2. Structural plate structures as described herein are
kN-m/m ))
those structures factory fabricated in plate form and bolted
D1556/D1556M Test Method for Density and Unit Weight
together on site to provide the required shape, size, and length
of Soil in Place by Sand-Cone Method
of structure. This practice applies to structures designed in
D1557 Test Methods for Laboratory Compaction Character-
accordance with Practice B790/B790M.
istics of Soil Using Modified Effort (56,000 ft-lbf/ft
1.2 The values stated in either inch-pound units or SI units
(2,700 kN-m/m ))
are to be regarded separately as standard. Within the text, the
D2167 Test Method for Density and Unit Weight of Soil in
SI units are shown in brackets. The values stated in each
Place by the Rubber Balloon Method
system are not exact equivalents; therefore, each system shall
D2487 Practice for Classification of Soils for Engineering
be used independently of the other. Combining values from the
Purposes (Unified Soil Classification System)
two systems may result in nonconformance with the standard.
D2937 Test Method for Density of Soil in Place by the
1.3 This standard does not purport to address all of the
Drive-Cylinder Method
safety concerns, if any, associated with its use. It is the D6938 TestMethodsforIn-PlaceDensityandWaterContent
responsibility of the user of this standard to establish appro-
of Soil and Soil-Aggregate by Nuclear Methods (Shallow
priate safety, health, and environmental practices and deter-
Depth)
mine the applicability of regulatory limitations prior to use.
1.4 This international standard was developed in accor-
3. Terminology
dance with internationally recognized principles on standard-
3.1 Definitions of Terms Specific to This Standard:
ization established in the Decision on Principles for the
3.1.1 arch, n—segment of a circular shape spanning an open
Development of International Standards, Guides and Recom-
invert between the footings on which it rests.
mendations issued by the World Trade Organization Technical
3.1.2 bedding, n—earth or other material on which a pipe is
Barriers to Trade (TBT) Committee.
supported.
2. Referenced Documents
3.1.3 haunch, n—portion of the pipe cross section between
the maximum horizontal dimension and the top of the bedding.
2.1 ASTM Standards:
B746/B746M Specification for CorrugatedAluminumAlloy 3.1.4 invert, n—lowest point on the pipe cross section; also,
the bottom portion of a pipe.
3.1.5 pipe, n—conduit having a full circular shape; also, in
This practice is under the jurisdiction of ASTM Committee B07 on Light
a general context, all structure shapes covered by this specifi-
Metals and Alloys and is the direct responsibility of Subcommittee B07.08 on
Corrugated Aluminum Pipe and Corrugated Aluminum Structural Plate. cation.
Current edition approved May 1, 2021. Published June 2021. Originally
3.1.6 pipe-arch, n—pipe with an approximate semicircular
approved in 1988. Last previous edition approved in 2016 as B789/B789M – 16.
crown, small-radius corners, and large-radius invert.
DOI: 10.1520/B0789_B0789M-16R21.
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
3.1.7 underpass, n—pipe with an approximate semicircular
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
crown, large-radius sides, small-radius corners between sides
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. and invert, and large-radius invert.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
B789/B789M − 16 (2021)
excavation must be in compliance with any local, state, and
federal codes and safety regulations.
6. Foundation
6.1 The supporting soil beneath the structure must provide a
reasonably uniform resistance to the imposed load, both
longitudinally and laterally. Sharp variations in the foundation
must be avoided. When rock is encountered, it must be
excavatedandreplacedwithsoil.Ifthestructureistobeplaced
onacontinuousrockfoundation,itwillbenecessarytoprovide
a bedding of soil between the rock and the structure. See Fig.
3.
6.2 Lateral changes in foundation should never be such that
the structure is firmly supported while the backfill on either
side is not.When soft material is encountered in the foundation
and must be removed to maintain the grade on the structure,
FIG. 1 Typical Trench Installation
then it must be removed, usually for a minimum of three
structure widths. See Fig. 4. A smaller width of removal can
sometimes be used if established by the engineer.
6.3 Performance of buried structures is enhanced by allow-
ing the structure to settle slightly relative to the columns of
earth alongside. Therefore, when significant settlement of the
overall foundation is expected, it is beneficial to provide a
yieldingfoundationunderstructuralplatestructures.Ayielding
foundationisonethatallowsthestructuretosettleverticallyby
a greater amount than the vertical settlement of the columns of
earth alongside. It can usually be obtained by placing beneath
the structure a layer of suitable thickness of compressible soil,
less densely compacted than the soil alongside. This is particu-
FIG. 2 Typical Embankment (Projection) Installation
larly important on structures with relatively large-radius invert
plates.
6.4 For all structures with relatively small-radius corner
plates adjacent to large-radius invert plates (such as pipe-
4. Significance and Use
arches or underpass structures), excellent soil support must be
4.1 Corrugated aluminum structural plate pipe functions
structurally as a flexible ring that is supported by and interacts
with the compacted surrounding soil. The soil placed around
the structure is thus an integral part of the structural system. It
is therefore important to ensure that the soil structure is made
up of the acceptable material and well-constructed. Field
verification of soil structure acceptability using Test Methods
D1556/D1556M, D2167, D6938,or D2937, as applicable, and
comparing the results with Test Methods D698 or D1557,in
accordance with the specifications for each project, is the most
reliable basis for installation of an acceptable structure. The
required density and method of measurement are not specified
by this practice but must be established in the specifications for
each project.
5. Trench Excavation
5.1 To obtain the anticipated structural performance of
structural plate structures, it is not necessary to control trench
width beyond the minimum necessary for proper assembly of
the structure and placement of the structural backfill. However,
the soil on each side beyond the excavated trench must be able
to support anticipated loads. When a construction situation 1
d = ⁄2 in./ft. [40 mm/m] of fill over pipe, with a 24-in. [600 mm] maximum.
calls for a relatively wide trench, it may be made as wide as
NOTE 1—Section B-B is applicable to all continuous rock foundations
required for its full depth, if so desired. However, trench FIG. 3 Foundation Transition Zones and Rock Foundations
B789/B789M − 16 (2021)
an excellent quality and highly compacted to accommodate the
high reaction pressures that can develop at that location. See
Fig. 5.
7.2 Structures having a span greater than 15 ft [4.5 m] or a
depth of cover greater than 20 ft [6 m] should be provided with
ashapedbeddingonayieldingfoundation.Thebeddingshould
be shaped to facilitate the required compaction of the structural
backfill under the haunches. A shaped bedding on a yielding
foundation is always required under structures with small-
radius corner plates adjacent to large-radius invert plates.
7.3 Material in contact with the pipe must not contain rock
retained on a 3-in. [75 mm] diameter ring, frozen lumps,
chunks of highly plastic clay, organic matter, corrosive
material, or other deleterious material.
FIG. 4 Soft Foundation Treatment
8. Assembly
8.1 Structural plate structures are furnished in components
of plates and fasteners for field assembly. These components
provided adjacent to the small-radius corner plates by both the
are furnished in accordance with Specification B746/B746M.
in-situ foundation and the structural backfill. See Fig. 4 and
Plates are furnished in a 4 ft, 6 in. [1372 mm] width and
Fig. 5. A yielding foundation must be provided beneath the
multiple lengths, preformed and punched for assembling into
invert plates for such structures when soft foundation condi-
the required structure shape, size, and length.The plate lengths
tions are encountered.
form the periphery of the structure. Arrange the single width
and the multiple lengths to allow for staggered, transverse
7. Bedding
seams to avoid four-plate laps. The fabricator of the structural
7.1 In most cases, structural plate structures may be as-
plate shall furnish an assembly drawing showing the location
sembled directly on in-situ material fine-graded to proper
of each plate by width, length, thickness, and curvature. The
alignment and grade. Take care to compact the material
plates must be assembled in accordance with the fabricator’s
beneath the haunches prior to placing structural backfill. For
drawing.
structures with relatively small-radius corner plates adjacent to
8.2 For structures with inverts, assembly shall begin with
large-radiusinvertplates,itisrecommendedtoeithershapethe
the invert plates at the downstream end. As the assembly
bedding to the invert plate radius or fine-grade the foundation
proceeds upstream, plates that fall fully or partly below the
to a slight v-shape. The soil adjacent to the corners must be of
maximum width of the structure are lapped over the preceding
plates to construct the transverse seams.
8.3 Arches on Footings:
8.3.1 Footings—Arches have no integral invert and usually
rest in key ways cast into footings. Key ways must be
accurately set to span, line, and grade, as shown in the plans
and specifications. When the arch is not a half circle, the key
way must be angled (rotated) or sized to allow proper entrance
of the plate. All pertinent dimensions must be shown on the
drawings.
8.3.2 Assembly—For arch structures, assembly typically
begins at the upstream end and proceeds downstream, with
each succeeding plate lapping on the outside of the previous
plate. There may be cases where it is more advantageous to
start assembly at some other point along the length of the
structure, such as is in the case where an elbow is involved.
During the erection of the ring, plates are not self-supporting
and must be temporarily supported. If the size of the key ways
is such that the plates may move during backfilling, the plates
must be temporarily blocked in the key ways to maintain span.
Assemble as few plates as practical. Start with a row of several
plates along both of the footings. Before finishing the bottom
row of plates, start at the end of the structure with the next row
ofplates.Beforereachingtheendofthefirstrowofplates,start
FIG. 5 Bedding and Corner Zone Treatment for Large-Radius In-
vert Plate Structures again at the end of the structure with the next row of plates.
B789/B789M − 16 (2021)
A,B
TABLE 1 Structural Backfill Width Requirements
Continue this process until the first ring is closed at its top, and
Adjacent Material Required Structural Backfill Width
then continue assembling all rows in this same manner. The
Normal highway embankment As needed to establish pipe bedding and
structure will have a “stair step” appearance as a result of this
compacted to minimum of to place and compact the backfill in the
procedure. This practice helps to hold the structure’s shape.
90 % Test Methods D698 haunch area and beside the pipe. Where
density, or equivalent trench backfill materials that do not require com-
8.4 Generally, structural plate should be assembled with as
wall. paction are used, such as cement slurry or
controlled low strength material (CLSM), a
few bolts as practical. These bolts should be placed loose and
minimum of 3 in. [75 mm] on each side of
remainlooseuntiltheperipheryhasbeencompletedforseveral
thepipeisrequired.
plate lengths. However, on large structures, it is practical to
Embankment or trench wall of Increase backfill width as necessary to
align bolt holes during assembly and tighten the bolts to
lesser quality. reduce horizontal pressure from pipe to a
maintain structure shape.After the periphery of the structure is
level compatible with bearing capacity of
completedforseveralplatelengths,allboltsmaybeplacedand
adjacent materials.
A
tightened. Correct any significant deviation in the structure
For pipe arches and other multiple radius structures, as well as for all structures
carryingoff-roadconstructionequipment,thestructuralbackfillwidth,includingany
shape before tightening bolts (see Section 10). It is advisable
necessary foundation improvement materials, must be sufficient to reduce the
not to tighten bolts on the loosely assembled structure within a
horizontal pressure from the structure so that it does not exceed the bearing
distance of 30 ft [9 m] of where plate assembly is ongoing.All
capacity of the adjacent material.
B
In embankment construction, the structural backfill width must be adequate to
bolts shall be tightened using an applied torque of between 100
resist forces caused by the embankment construction equipment. Gene
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.