ASTM D3110-95

Specification for Adhesives Used in Laminate Joints for Nonstructural Glued Lumber Products (Withdrawn 1996)

General Information

• Status: Withdrawn
• Withdrawal Date: 09-Mar-1996
• ICS: 83.180 - Adhesives
• Technical Committee: D14 - Adhesives
• Drafting Committee: D14.30 - Wood Adhesives

Standards Content (Sample)

ASTM D~IIIIO 95 = 0759530 0568548 377 -
AMERICAN SOCIETY FOR TESTING AND MATERIALS
Designation: D 3110 - 95
100 Barr Ha&w Dr , West Conshohocken. PA 19428
Repnnted from the Annual Book of ASTM Standards Copynght ASTM
#Tb
If not llstad m the currant combwfl index, will appear in the next adltlon
Standard Specification for
Adhesives Used in Laminate Joints for Nonstructural Glued
Lumber Products’
This standard is issued under the fixed designation D 31 IO; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (6) indicates an editorral change since the last revision or reapprowl.
INTRODUCTION
In 1989, Subcommittee D 14.30 made the decision to split Specification D 3 110 into two
standards, one addressing finger joints and the other laminate joints. Specification D 5572 has been
approved.
The laminate joint portion, Proposed Standard Specification for Adhesive Used for Laminate
Joints in Nonstructural Lumber Products, is in the balloting process. Until the standard has been
approved, Specification D 3110 will appear as in this revision, addressing only the laminate joint
portion.
1. Scope E 6 Terminology Relating to Methods of Mechanical
Testing4
1.1 This specification establishes acceptable performance
E 4 1 Terminology Relating to Conditioning5
levels for glues or adhesives to be used in nonstructural glued
lumber products. Such products include, but are not limited
3. Terminology
to, interior and exterior moldings, window and door stock,
3.1 Definitions-For other terms used in this specifica-
and glued lumber panels. Adhesives that meet the respective
tion, refer to Terminologies D 907, E 6, and E 41.
requirements of the certification tests are considered capable
3. I. 1 laminatejoint-A joint made by bonding adherends
of providing an adequate bond for use under the conditions
face-to-face or edge-to-edge (with the grain direction parallel)
described for the class. This specification is to be used to
to form thicker or wider stock.
evaluate adhesives only and is not to be used to evaluate the
industrial end products (glued wood products) made with
4. Classification of Adhesive Performance
adhesives.
4.1 For purposes of this specification, adhesives are classi-
1.2 The following safety hazards caveat applies only to the
fied on the basis of two performance levels, wet-use and
test methods portion, Sections 6 through 12, of this specifi-
dry-use.
cation: This standard does not purport to address all of the
4.1.1 Wet-Use Nonstructural Adhesive-One capable of
safety concerns, if any, associated with its use. It is the
producing sufftcient glue-joint strength and durability to
responsibility of the user of this standard to establish appro-
make the glued lumber product serviceable in nonstructural
priate safety and health practices and determine the applica-
use under conditions in which the equilibrium moisture
bility of regulatory limitations prior to use.
content (EMC) of the wood may be 16 % or greater, and
where the temperature may reach levels as high as 165’ F
(74”C), at times, during service. Table I outlines the appli-
2. Referenced Documents
cable tests and performance requirements for a wet-use
2.1 ASTM Standards:
nonstructural adhesive.
D905 Test Method for Strength Properties of Adhesive
4.1.2 Dry-Use Nonstructural Adhesive-One capable of
Bonds in Shear by Compression Loading2
producing sufficient glue-joint strength and durability to
D 907 Terminology of Adhesives2
make the glued lumber product serviceable in nonstructural
D 20 16 Test Methods for Moisture Content of Wood3
use, under conditions in which the equilibrium moisture
D2555 Test Methods for Establishing Clear-Wood
content (EMC) of the wood does not exceed 16 %, and where
Strength Values3
the temperature does not exceed 165°F (74°C) for as long as
E 4 Practices for Force Verification of Testing Machines4
6 h during shipment, or 140°F (6O’C) continuously during
service. Table 1 outlines the applicable tests and performance
requirements for a dry-use nonstructural adhesive.
t This specification is under the jurisdtction of ASTM Committee D-14 on
Adhesives and is the direct responsibility of Subcommittee D14.30 on Wood
5. Classification of Glued Lumber Joints
Adhesives.
Current edition approved June 15, 1995. Published August 1995. Originally
5.1 There is one class, the laminate joint.
published as D 31 IO - 72. Last previous edition D 31 IO - 90”.
2 Annual Book of ASTM Slandards, Vol 15.06.
3 Annual Book of ASTM Standards, Vol 04. IO.
5 Annual Book of ASTM Standards, Vol 14.02.
4 Annual Book of ASTM Slundards, Vol 03.0 I.
COPYRIGHT American Society for Testing and MaterialsCOPYRIGHT American Society for Testing and Materials
Licensed by Information Handling ServicesLicensed by Inf
...