ASTM C591-08a
(Specification)Standard Specification for Unfaced Preformed Rigid Cellular Polyisocyanurate Thermal Insulation
Standard Specification for Unfaced Preformed Rigid Cellular Polyisocyanurate Thermal Insulation
ABSTRACT
This specification covers the types, physical properties, and dimensions of unfaced, preformed rigid cellular polyurethane modified polyisocyanurate plastic material intended for use as thermal insulation on surfaces. This insulation can be classified into six types according to its compressive resistance: Types I, IV, II, III, V, and VI. Also this insulation can be classified as Grades 1 and 2 according to its service temperature range. The thermal insulation is produced by the polymerization of polymeric polyisocyanates in the presence of polyhydroxyl compounds, catalysts, cell stabilizers, and blowing agents. Different test methods shall be performed in order to determine the thermal insulation's following properties: density, compressive resistance, apparent thermal conductivity, hot-surface performance, water absorption, water vapor permeability, dimensional stability, closed-cell content, surface bearing characteristics, tensile strength, and leachable chloride, fluoride, silicate, and sodium ions.
SCOPE
1.1 This specification covers the types, physical properties, and dimensions of unfaced, preformed rigid cellular polyisocyanurate plastic material intended for use as thermal insulation on surfaces from − 297°F (−183°C) to 300°F (150°C). For specific applications, the actual temperature limits shall be agreed upon by the manufacturer and purchaser.
1.2 This specification only covers “polyurethane modified polyisocyanurate” thermal insulation which is commonly referred to as “polyisocyanurate” thermal insulation. This standard does not encompass all polyurethane modified materials. Polyurethane modified polyisocyanurate and other polyurethane materials are similar, but the materials will perform differently under some service conditions.
1.3 This standard is designed as a material specification, not a design document. Physical property requirements vary by application and temperature. At temperatures below - 70°F (- 51°C) the physical properties of the polyisocyanurate insulation at the service temperature are of particular importance. Below - 70°F (- 51°C) the manufacturer and the purchaser must agree on what additional cold temperature performance properties are required to determine if the material can function adequately for the particular application.
1.4 Tables in the Annex A1 address requirements of unfaced preformed rigid cellular polyisocyanurate thermal insulation manufactured with HCFC blowing agent.
1.5 When adopted by an authority having jurisdiction, codes that address fire properties in many applications regulate the use of the thermal insulation materials covered by this specification. Fire properties are controlled by job, project, or other specifications where codes or government regulations do not apply.
1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: C591 – 08a
Standard Specification for
Unfaced Preformed Rigid Cellular Polyisocyanurate
1
Thermal Insulation
This standard is issued under the fixed designation C591; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope 1.6 The values stated in inch-pound units are to be regarded
as standard. The values given in parentheses are mathematical
1.1 This specification covers the types, physical properties,
conversions to SI units that are provided for information only
and dimensions of unfaced, preformed rigid cellular polyiso-
and are not considered standard.
cyanurate plastic material intended for use as thermal insula-
1.7 This standard does not purport to address all of the
tiononsurfacesfrom−297°F(−183°C)to300°F(150°C).For
safety concerns, if any, associated with its use. It is the
specific applications, the actual temperature limits shall be
responsibility of the user of this standard to establish appro-
agreed upon by the manufacturer and purchaser.
priate safety and health practices and determine the applica-
1.2 This specification only covers “polyurethane modified
bility of regulatory limitations prior to use.
polyisocyanurate” thermal insulation which is commonly re-
ferred to as “polyisocyanurate” thermal insulation. This stan-
2. Referenced Documents
dard does not encompass all polyurethane modified materials.
2
2.1 ASTM Standards:
Polyurethane modified polyisocyanurate and other polyure-
C165 Test Method for Measuring Compressive Properties
thane materials are similar, but the materials will perform
of Thermal Insulations
differently under some service conditions.
C168 Terminology Relating to Thermal Insulation
1.3 Thisstandardisdesignedasamaterialspecification,not
C177 Test Method for Steady-State Heat Flux Measure-
a design document. Physical property requirements vary by
ments and Thermal Transmission Properties by Means of
application and temperature. At temperatures below -70°F
the Guarded-Hot-Plate Apparatus
(-51°C) the physical properties of the polyisocyanurate insu-
C272 Test Method for Water Absorption of Core Materials
lation at the service temperature are of particular importance.
for Structural Sandwich Constructions
Below -70°F (-51°C) the manufacturer and the purchaser
C303 Test Method for Dimensions and Density of Pre-
must agree on what additional cold temperature performance
formed Block and Board−Type Thermal Insulation
propertiesarerequiredtodetermineifthematerialcanfunction
C335 Test Method for Steady-State Heat Transfer Proper-
adequately for the particular application.
ties of Pipe Insulation
1.4 TablesintheAnnexA1addressrequirementsofunfaced
C390 Practice for Sampling and Acceptance of Thermal
preformed rigid cellular polyisocyanurate thermal insulation
Insulation Lots
manufactured with HCFC blowing agent.
C411 Test Method for Hot-Surface Performance of High-
1.5 Whenadoptedbyanauthorityhavingjurisdiction,codes
Temperature Thermal Insulation
that address fire properties in many applications regulate the
C518 Test Method for Steady-State Thermal Transmission
use of the thermal insulation materials covered by this speci-
Properties by Means of the Heat Flow Meter Apparatus
fication. Fire properties are controlled by job, project, or other
C550 Test Method for Measuring Trueness and Squareness
specifications where codes or government regulations do not
of Rigid Block and Board Thermal Insulation
apply.
C585 Practice for Inner and Outer Diameters of Thermal
Insulation for Nominal Sizes of Pipe and Tubing
1
This specification is under the jurisdiction of ASTM Committee C16 on
Thermal Insulation and is the direct responsibility of Subcommittee C16.22 on
2
Organic and Nonhomogeneous Inorganic Thermal Insulations. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved Dec. 1, 2008. Published January 2009. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 1966. Last previous edition approved in 2008 as C591–08. DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/C0591-08A. the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
C591 – 08a
A
TABLE 1 Physical Property Requirements
Grade 1: Operating Temperature Range -70°F (-51°C) to 300°F (149°C)
Property Type I Type IV Type II Type III Type V Type VI
3 3
Density, min lb/ft (kg/m
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:C591–08 Designation: C 591 – 08a
Standard Specification for
Unfaced Preformed Rigid Cellular Polyisocyanurate
1
Thermal Insulation
This standard is issued under the fixed designation C591; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope
1.1 This specification covers the types, physical properties, and dimensions of unfaced, preformed rigid cellular polyisocya-
nurate plastic material intended for use as thermal insulation on surfaces from −297°F (−183°C) to 300°F (150°C). For specific
applications, the actual temperature limits shall be agreed upon by the manufacturer and purchaser.
1.2 This specification only covers “polyurethane modified polyisocyanurate” thermal insulation which is commonly referred to
as “polyisocyanurate” thermal insulation. This standard does not encompass all polyurethane modified materials. Polyurethane
modified polyisocyanurate and other polyurethane materials are similar, but the materials will perform differently under some
service conditions.
1.3 This standard is designed as a material specification, not a design document. Physical property requirements vary by
application and temperature. At temperatures below -70°F (-51°C) the physical properties of the polyisocyanurate insulation at
theservicetemperatureareofparticularimportance.Below-70°F(-51°C)themanufacturerandthepurchasermustagreeonwhat
additional cold temperature performance properties are required to determine if the material can function adequately for the
particular application.
1.4 Tables in the Annex A1 address requirements of unfaced preformed rigid cellular polyisocyanurate thermal insulation
manufactured with HCFC blowing agent.
1.5The use of thermal insulation material covered by this specification may be regulated by building codes that address fire
performance.
1.5 When adopted by an authority having jurisdiction, codes that address fire properties in many applications regulate the use
of the thermal insulation materials covered by this specification. Fire properties are controlled by job, project, or other
specifications where codes or government regulations do not apply.
1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
C165 Test Method for Measuring Compressive Properties of Thermal Insulations
C168 Terminology Relating to Thermal Insulation
C177 Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the
Guarded-Hot-Plate Apparatus
C203Test Methods for Breaking Load and Flexural Properties of Block-Type Thermal Insulation
C272 Test Method for Water Absorption of Core Materials for Structural Sandwich Constructions
C303 Test Method for Dimensions and Density of Preformed Block and BoardType Thermal Insulation
C335 Test Method for Steady-State Heat Transfer Properties of Pipe Insulation
C390 Practice for Sampling and Acceptance of Thermal Insulation Lots
C411 Test Method for Hot-Surface Performance of High-Temperature Thermal Insulation
1
This specification is under the jurisdiction of ASTM Committee C16 on Thermal Insulation and is the direct responsibility of Subcommittee C16.22 on Organic and
Nonhomogeneous Inorganic Thermal Insulations.
CurrenteditionapprovedJuneDec.1,2008.PublishedJune2008.January2009.Originallyapprovedin1966.Lastpreviouseditionapprovedin20072008asC591–078.
2
ForreferencedASTMstandards,visittheASTMwebsite,www.astm.org,orcontactASTMCustomerServiceatservice@astm.org.For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
C 591 – 08a
A
TABLE 1 Physical
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:C591–08 Designation: C 591 – 08a
Standard Specification for
Unfaced Preformed Rigid Cellular Polyisocyanurate
1
Thermal Insulation
This standard is issued under the fixed designation C591; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope
1.1 This specification covers the types, physical properties, and dimensions of unfaced, preformed rigid cellular polyisocya-
nurate plastic material intended for use as thermal insulation on surfaces from −297°F (−183°C) to 300°F (150°C). For specific
applications, the actual temperature limits shall be agreed upon by the manufacturer and purchaser.
1.2 This specification only covers “polyurethane modified polyisocyanurate” thermal insulation which is commonly referred to
as “polyisocyanurate” thermal insulation. This standard does not encompass all polyurethane modified materials. Polyurethane
modified polyisocyanurate and other polyurethane materials are similar, but the materials will perform differently under some
service conditions.
1.3 This standard is designed as a material specification, not a design document. Physical property requirements vary by
application and temperature. At temperatures below -70°F (-51°C) the physical properties of the polyisocyanurate insulation at
theservicetemperatureareofparticularimportance.Below-70°F(-51°C)themanufacturerandthepurchasermustagreeonwhat
additional cold temperature performance properties are required to determine if the material can function adequately for the
particular application.
1.4 Tables in the Annex A1 address requirements of unfaced preformed rigid cellular polyisocyanurate thermal insulation
manufactured with HCFC blowing agent.
1.5The use of thermal insulation material covered by this specification may be regulated by building codes that address fire
performance.
1.5 When adopted by an authority having jurisdiction, codes that address fire properties in many applications regulate the use
of the thermal insulation materials covered by this specification. Fire properties are controlled by job, project, or other
specifications where codes or government regulations do not apply.
1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
C165 Test Method for Measuring Compressive Properties of Thermal Insulations
C168 Terminology Relating to Thermal Insulation
C177 Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the
Guarded-Hot-Plate Apparatus
C203Test Methods for Breaking Load and Flexural Properties of Block-Type Thermal Insulation
C272 Test Method for Water Absorption of Core Materials for Structural Sandwich Constructions
C303 Test Method for Dimensions and Density of Preformed Block and BoardType Thermal Insulation
C335 Test Method for Steady-State Heat Transfer Properties of Pipe Insulation
C390 Practice for Sampling and Acceptance of Thermal Insulation Lots
C411 Test Method for Hot-Surface Performance of High-Temperature Thermal Insulation
1
This specification is under the jurisdiction of ASTM Committee C16 on Thermal Insulation and is the direct responsibility of Subcommittee C16.22 on Organic and
Nonhomogeneous Inorganic Thermal Insulations.
CurrenteditionapprovedJuneDec.1,2008.PublishedJune2008.January2009.Originallyapprovedin1966.Lastpreviouseditionapprovedin20072008asC591–078.
2
ForreferencedASTMstandards,visittheASTMwebsite,www.astm.org,orcontactASTMCustomerServiceatservice@astm.org.For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
C 591 – 08a
A
TABLE 1 Physical
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.