ASTM B42-15
(Specification)Standard Specification for Seamless Copper Pipe, Standard Sizes
Standard Specification for Seamless Copper Pipe, Standard Sizes
ABSTRACT
This specification covers seamless copper pipe in all nominal standard pipe sizes, both regular and extra-strong, suitable for use in plumbing, boiler feed lines, and for similar purposes. The material shall conform to the specified chemical requirements. The pipe shall be produced from one of C10200, C10300, C10800, C12000, and C12200 copper UNS numbers. All pipes shall normally be furnished in the prescribed annealed, light drawn, or hard drawn temper. The pipe shall be made from copper that is free of cuprous oxide, as determined by microscopical examination. The pipe shall be subjected to expansion or flattening, Eddy-current, and hydrostatic tests. Samples for chemical analysis shall be taken in accordance with Practice E255. However, the manufacturer shall have the option of determining conformance by analyzing samples taken at the time the castings are poured or from the semifinished product, subject to the conditions set in the specification.
SIGNIFICANCE AND USE
15.1 For purposes of determining compliance with the specified limits for requirements of the properties listed in the following table, an observed value or a calculated value shall be rounded as indicated in accordance with the rounding method of Practice E29.
Property
Rounded Unit for
Observed or Calculated Value
Chemical composition
nearest unit in the last right-hand place of figures of the specified limit
Tensile strength
Yield strength
nearest ksi (nearest 5 MPa)
SCOPE
1.1 This specification2 establishes the requirements for seamless copper pipe in all nominal or standard pipe sizes, both regular and extra-strong, suitable for use in plumbing, boiler feed lines, and for similar purposes.3
1.2 Units—The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are mathematical conversions to SI units, which are provided for information only and are not considered standard.
1.3 The following safety hazard caveat pertains only to the test methods described in this specification.
1.3.1 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:B42 −15
StandardSpecification for
1
Seamless Copper Pipe, Standard Sizes
ThisstandardisissuedunderthefixeddesignationB42;thenumberimmediatelyfollowingthedesignationindicatestheyearoforiginal
adoptionor,inthecaseofrevision,theyearoflastrevision.Anumberinparenthesesindicatestheyearoflastreapproval.Asuperscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope* B846Terminology for Copper and Copper Alloys
2 B968/B968MTest Method for Flattening of Copper and
1.1 This specification establishes the requirements for
Copper-Alloy Pipe and Tube
seamlesscopperpipeinallnominalorstandardpipesizes,both
E8/E8MTest Methods for Tension Testing of Metallic Ma-
regular and extra-strong, suitable for use in plumbing, boiler
3 terials
feed lines, and for similar purposes.
E29Practice for Using Significant Digits in Test Data to
1.2 Units—The values stated in inch-pound units are to be
Determine Conformance with Specifications
regarded as the standard. The values given in parentheses are
E53Test Method for Determination of Copper in Unalloyed
mathematical conversions to SI units, which are provided for
Copper by Gravimetry
information only and are not considered standard.
E62Test Methods for Chemical Analysis of Copper and
5
1.3 The following safety hazard caveat pertains only to the CopperAlloys(PhotometricMethods)(Withdrawn2010)
E243PracticeforElectromagnetic(EddyCurrent)Examina-
test methods described in this specification.
1.3.1 This standard does not purport to address all of the tion of Copper and Copper-Alloy Tubes
E255Practice for Sampling Copper and Copper Alloys for
safety concerns, if any, associated with its use. It is the
responsibility of the user of this standard to establish appro- the Determination of Chemical Composition
E478Test Methods for ChemicalAnalysis of CopperAlloys
priate safety and health practices and determine the applica-
bility of regulatory limitations prior to use. E527Practice for Numbering Metals and Alloys in the
Unified Numbering System (UNS)
2. Referenced Documents
4
3. Terminology
2.1 ASTM Standards:
B153Test Method for Expansion (Pin Test) of Copper and 3.1 Definitions:
Copper-Alloy Pipe and Tubing
3.1.1 For definitions of terms related to copper and copper
B170Specification for Oxygen-Free Electrolytic Copper— alloys, refer to Terminology B846.
Refinery Shapes
B577TestMethodsforDetectionofCuprousOxide(Hydro- 4. Ordering Information
gen Embrittlement Susceptibility) in Copper
4.1 Include the following specified choices when placing
B601ClassificationforTemperDesignationsforCopperand
orders for product under this specification as applicable:
Copper Alloys—Wrought and Cast
4.1.1 ASTM designation and year of issue,
4.1.2 CopperUNSNo.designation,ifrequired,(seeChemi-
cal Composition section),
1
ThisspecificationisunderthejurisdictionofASTMCommitteeB05onCopper
4.1.3 Temper (see Temper section and Table 2),
and CopperAlloys and is the direct responsibility of Subcommittee B05.04 on Pipe
4.1.4 Pipe size, regular or extra-strong, (see Dimensions
and Tube.
Current edition approved May 15, 2015. Published July 2015. Originally
section and Table 3),
approved in 1922. Last previous edition approved in 2010 as B42–10. DOI:
4.1.5 Length (see 10.3) if different than standard,
10.1520/B0042-15.
4.1.6 Total length of each size,
2
For ASME Boiler and Pressure Vessel Code applications, see related Specifi-
cation SB-42 in Section II of that Code.
4.2 The following options are available, but may not be
3
The UNS system for copper and copper alloys (see Practice E527) is a simple
included unless specified at the time of placing of the order
expansion of the former standard designation system accomplished by the addition
when required:
of a prefix “C” and a suffix “00.” The suffix can be used to accommodate
composition variations of the base alloy.
4
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
5
Standards volume information, refer to the standard’s Document Summary page on The last approved version of this historical standard is referenced on
the ASTM website. www.astm.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
B42−15
4.2.1 If product is ordered for ASME Boiler and Pressure 6.1.2 Light Drawn H55
Vessel Code Application (See Certification Section). 6.1.3 Hard Drawn H80
4.2.2 If product is required for bending (see 6.2) and the
6.2 When pipe is required for bending, it shall be so
temper to be furnished,
specified in the purchase ord
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: B42 − 10 B42 − 15
Standard Specification for
1
Seamless Copper Pipe, Standard Sizes
This standard is issued under the fixed designation B42; the number immediately following the designation indicates the year of original
adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope*
2
1.1 This specification establishes the requirements for seamless copper pipe in all nominal or standard pipe sizes, both regular
3
and extra-strong, suitable for use in plumbing, boiler feed lines, and for similar purposes.
1.2 Units—The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are
mathematical conversions to SI units, which are provided for information only and are not considered standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
1.3 The following safety hazard caveat pertains only to the test methods described in this specification.
1.3.1 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
4
2.1 ASTM Standards:
B153 Test Method for Expansion (Pin Test) of Copper and Copper-Alloy Pipe and Tubing
B170 Specification for Oxygen-Free Electrolytic Copper—Refinery Shapes
B577 Test Methods for Detection of Cuprous Oxide (Hydrogen Embrittlement Susceptibility) in Copper
B601 Classification for Temper Designations for Copper and Copper Alloys—Wrought and Cast
B846 Terminology for Copper and Copper Alloys
B968/B968M Test Method for Flattening of Copper and Copper-Alloy Pipe and Tube
E8E8/E8M Test Methods for Tension Testing of Metallic Materials
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E53 Test Method for Determination of Copper in Unalloyed Copper by Gravimetry
5
E62 Test Methods for Chemical Analysis of Copper and Copper Alloys (Photometric Methods) (Withdrawn 2010)
E243 Practice for Electromagnetic (Eddy Current) Examination of Copper and Copper-Alloy Tubes
E255 Practice for Sampling Copper and Copper Alloys for the Determination of Chemical Composition
E478 Test Methods for Chemical Analysis of Copper Alloys
E527 Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)
3. Terminology
3.1 Definitions:
3.1.1 For definitions of terms related to copper and copper alloys, refer to Terminology B846.
1
This specification is under the jurisdiction of ASTM Committee B05 on Copper and Copper Alloys and is the direct responsibility of Subcommittee B05.04 on Pipe and
Tube.
Current edition approved Oct. 1, 2010May 15, 2015. Published November 2010July 2015. Originally approved in 1922. Last previous edition approved in 20022010 as
ε1
B42 – 02B42 – 10. . DOI: 10.1520/B0042-10.10.1520/B0042-15.
2
For ASME Boiler and Pressure Vessel Code applications, see related Specification SB-42 in Section II of that Code.
3
The UNS system for copper and copper alloys (see Practice E527) is a simple expansion of the former standard designation system accomplished by the addition of a
prefix “C” and a suffix “00.” The suffix can be used to accommodate composition variations of the base alloy.
4
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
5
The last approved version of this historical standard is referenced on www.astm.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
B42 − 15
3.1.2 pipe—a seamless tube conforming to the particular dimensions commercially known as Nominal or Standard Pipe Sizes.
4. Ordering Information
4.1 Include the following specified choices
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.