ASTM E1920-03(2021)
(Guide)Standard Guide for Metallographic Preparation of Thermal Sprayed Coatings
Standard Guide for Metallographic Preparation of Thermal Sprayed Coatings
SIGNIFICANCE AND USE
4.1 TSCs are used in a number of critical industrial components. TSCs can be expected to contain measurable levels of porosity and linear detachment. Accurate and consistent evaluation of specimens is essential to ensure the integrity of the coating and proper adherence to the substrate.
4.1.1 Example 1: By use of inappropriate metallographic methods, the apparent amount of porosity and linear detachment displayed by a given specimen can be increased, by excessive edge rounding, or decreased by smearing of material into voids. Therefore inaccurate levels of porosity and linear detachment will be reported even when the accuracy of the measurement technique is acceptable.
4.1.2 Example 2: Inconsistent metallographic preparation methods can cause the apparent amount of voids to vary excessively indicating a poorly controlled thermal spray process, while the use of consistent practice will regularly display the true microstructure and verify the consistency of the thermal spray process.
4.2 During the development of TSC procedures, metallographic information is necessary to validate the efficacy of a specific application.
4.3 Cross sections are usually taken perpendicular to the long axis of the specimen and prepared to reveal information concerning the following:
4.3.1 Variations in structure from surface to substrate,
4.3.2 The distribution of unmelted particles throughout the coating,
4.3.3 The distribution of linear detachment throughout the coating,
4.3.4 The distribution of porosity throughout the coating,
4.3.5 The presence of contamination within the coating,
4.3.6 The thickness of the coating (top coat and bond coat, where applicable),
4.3.7 The presence of interfacial contamination,
4.3.8 The integrity of the interface between the coating and substrate, and,
4.3.9 The integrity of the coating microstructure with respect to chemistry.
SCOPE
1.1 This guide covers recommendations for sectioning, cleaning, mounting, grinding, and polishing to reveal the microstructural features of thermal sprayed coatings (TSCs) and the substrates to which they are applied when examined microscopically. Because of the diversity of available equipment, the wide variety of coating and substrate combinations, and the sensitivity of these specimens to preparation technique, the existence of a series of recommended methods for metallographic preparation of thermal sprayed coating specimens is helpful. Adherence to this guide will provide practitioners with consistent and reproducible results. Additional information concerning standard practices for metallographic preparation can be found in Guide E3.
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: E1920 − 03 (Reapproved 2021)
Standard Guide for
Metallographic Preparation of Thermal Sprayed Coatings
This standard is issued under the fixed designation E1920; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 3.2 Definitions of Terms Specific to This Standard:
3.2.1 linear detachment, n—a region within a TSC in which
1.1 This guide covers recommendations for sectioning,
two successively deposited splats of coating material have not
cleaning, mounting, grinding, and polishing to reveal the
metallurgically bonded.
microstructural features of thermal sprayed coatings (TSCs)
and the substrates to which they are applied when examined 3.2.2 splat, n—an individual globule of thermal sprayed
microscopically. Because of the diversity of available material that has been deposited on a substrate.
equipment, the wide variety of coating and substrate
3.2.3 taper mount, n—ametallographicspecimencreatedby
combinations, and the sensitivity of these specimens to prepa-
mounting a feature, typically an interface or thin coating, at a
ration technique, the existence of a series of recommended
small angle to the polishing plane, such that the visible width
methods for metallographic preparation of thermal sprayed
exhibited by the feature is expanded.
coating specimens is helpful. Adherence to this guide will
3.2.4 TSC, n—thermal sprayed coating, including, but not
provide practitioners with consistent and reproducible results.
limited to, those formed by plasma, flame, and high velocity
Additional information concerning standard practices for met-
oxyfuel.
allographic preparation can be found in Guide E3.
1.2 This standard does not purport to address all of the
4. Significance and Use
safety concerns, if any, associated with its use. It is the
4.1 TSCs are used in a number of critical industrial compo-
responsibility of the user of this standard to establish appro-
nents. TSCs can be expected to contain measurable levels of
priate safety, health, and environmental practices and deter-
porosity and linear detachment.Accurate and consistent evalu-
mine the applicability of regulatory limitations prior to use.
ation of specimens is essential to ensure the integrity of the
1.3 This international standard was developed in accor-
coating and proper adherence to the substrate.
dance with internationally recognized principles on standard-
4.1.1 Example 1: By use of inappropriate metallographic
ization established in the Decision on Principles for the
methods, the apparent amount of porosity and linear detach-
Development of International Standards, Guides and Recom-
ment displayed by a given specimen can be increased, by
mendations issued by the World Trade Organization Technical
excessive edge rounding, or decreased by smearing of material
Barriers to Trade (TBT) Committee.
into voids. Therefore inaccurate levels of porosity and linear
detachment will be reported even when the accuracy of the
2. Referenced Documents
2 measurement technique is acceptable.
2.1 ASTM Standards:
4.1.2 Example 2: Inconsistent metallographic preparation
E3 Guide for Preparation of Metallographic Specimens
methods can cause the apparent amount of voids to vary
E7 Terminology Relating to Metallography
excessively indicating a poorly controlled thermal spray
process, while the use of consistent practice will regularly
3. Terminology
display the true microstructure and verify the consistency of
3.1 Definitions—For definitions of terms used in this guide,
the thermal spray process.
see Terminology E7.
4.2 During the development of TSC procedures, metallo-
graphic information is necessary to validate the efficacy of a
1 specific application.
ThisguideisunderthejurisdictionofASTMCommitteeE04onMetallography
and is the direct responsibility of Subcommittee E04.01 on Specimen Preparation.
4.3 Cross sections are usually taken perpendicular to the
Current edition approved Sept. 1, 2021. Published November 2021. Originally
long axis of the specimen and prepared to reveal information
approvedin1997.Lastpreviouseditionapprovedin2014asE1920–03(2014).DOI:
10.1520/E1920-03R21.
concerning the following:
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
4.3.1 Variations in structure from surface to substrate,
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
4.3.2 The distribution of unmelted particles throughout the
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. coating,
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
E1920 − 03 (2021)
4.3.3 The distribution of linear detachment throughout the 6.2.5.1 Use a diamond wafering blade with a maximum
coating, thickness of 0.63 mm (0.025 in.).
4.3.4 The distribution of porosity throughout the coating,
6.2.5.2 Use an ultra–thin aluminum oxide abrasive blade
4.3.5 The presence of contamination within the coating,
approximately 0.76 mm (0.030 in.) thick, which will break
4.3.6 The thickness of the coating (top coat and bond coat,
down during cutting to help reduce sectioning damage.
where applicable),
6.2.6 Faster blade speeds, 1675 m/min. (5500 surface ft/
4.3.7 The presence of interfacial contamination,
min.) or greater, produce less coating damage. Slower blade
4.3.8 The integrity of the interface between the coating and
speedswillresultinmoredamagetothecutsurfaceandarenot
substrate, and,
recommended.
4.3.9 The integrity of the coating microstructure with re-
6.2.7 Generally, an abrasive cutoff blade selected to cut the
spect to chemistry.
substrate effectively will be the best blade for the combination
of TSC and substrate.
5. Selection of Metallographic Specimens
5.1 Selection of specimens for metallographic examination 7. Cleaning
is critical if their interpretation is to be of value. Specimens
7.1 Cleaning of specimens prior to mounting is essential.
must be representative of the coating. Generally, the plane of
All sectioning coolant shall be removed from the surface and
polish should be normal to the coating surface so as to display
from any porosity connected to the surface. Use of an organic
the entire coating thickness, the substrate, and all interfaces.
solvent to aid in fluid removal and thorough drying is neces-
sary. Drying in an oven at low temperature (60 °C to 80 °C or
6. Sectioning
140 °F to 176 °F) can accelerate this process. Any liquid
6.1 Specimens to be mounted for metallographic prepara-
residualmayimpedeimpregnationofporosity,aswellasretard
tion are generally not larger than 12 mm by 25 mm (0.5 by 1.0
the curing of mounting compounds causing difficulty during
in.). The height of the mounted specimen should be no greater
grinding and polishing.
than necessary for convenient handling during polishing.
7.2 Ultrasonic cleaning of TSC specimens is generally not
6.2 In sectioning TSC specimens, care must be exercised to
recommended,especiallyforfragileorbrittlecoatings,because
avoid affecting the soundness of the coating and the interface
coating particles may be lost during this energetic cleaning
between the coating and the substrate. Sectioning damage of
process. If ultrasonic cleaning is found to be necessary,
thecoatingandinterfacethatcannotberemovedbysubsequent
cleaning time should be kept to a minimum.
grinding and polishing must be avoided.
6.2.1 Friable, porous, or brittle coatings to be sectioned may
8. Mounting
be vacuum impregnated with epoxy mounting compound
8.1 General Information:
before sectioning to protect the specimen.
8.1.1 It is always necessary to mount TSC specimens to
6.2.2 Specimens should always be sectioned such that the
maintain the original structure of the specimen during grinding
coating is compressed into the substrate. Sectioning techniques
and polishing. Both compression mounting and castable
which place the coating and interface in tension are strictly to
mountingcompoundsarecommonlyusedwhenmountingTSC
be avoided. Sectioning in tension may cause the coating to be
specimens. However, only castable epoxy mounting com-
pulled away from the substrate or result in delamination of the
pounds should be used in the initial determination of the true
coating. During examination of the polished specimens, it is
characteristics of a coating before considering the use of any
likely that this type of damage will be mistakenly interpreted.
other mounting compound. For some TSC specimens castable
When sectioning some specimens, it may not be possible to
epoxy may provide the only acceptable mount. Refer to Table
avoid placing some areas of the TSC in tension. These areas
1 and Table 2 and Practice E3 for characteristics of various
should be noted and not included in the evaluation of the
mounting compounds.
specimen.
8.1.2 Byplacingpairsofspecimensinthesamemount,time
6.2.3 Sectioning with a hack saw will produce significant
and expense can be saved. When using this mounting method,
damage to the coating and interface and is not considered
the two coated surfaces should face each other. It may be
acceptable.
possible to place more than one pair of specimens in a single
6.2.4 Using an abrasive cutoff blade with a large particle
mount.
size abrasive produces a smoother surface than a hack saw, but
8.1.3 Mounting expenses may be reduced by employing the
still produces coating damage that may require considerable
sandwich mount technique. A sandwich mount is made by
grinding in subsequent preparation to remove. The choice of
using a small amount of a better, more expensive, mounting
cutoff wheel, coolant, cutting conditions, and the type and
compoundasthecriticallayerincontactwiththespecimenand
hardness of the coating and substrate will influence the quality
then topping off the mount with a less expensive compound.
of the cut surface. A poor choice of cutting conditions can
Care must be taken to use only mounting materials that are
easily overheat some TSC specimens rendering the specimens
compatible.
unusable for proper evaluation.
6.2.5 Sectioning can be completed with minimal damage to 8.1.4 Taper mounting may be useful for examination of the
the cut surface by selection of one of the two following interfaces between bond coating and top coating, as well as
abrasive cutoff blades: between coating and substrate.
E1920 − 03 (2021)
TABLE 1 Characteristics of Compression Mounting Compounds
mixing two components just prior to use. The specimen is
A
Type of Compound Characteristics placed in a mold, usually a cup or ringform, into which the
Acrylic Cure time 10 min to 15 min., optically clear, compound is poured.
thermoplastic, good impregnation, low hardness,
8.3.2 Vacuum impregnation of porous specimens with an
degraded by hot etchants
epoxy resin is required. The specimen and mold are put into a
Diallyl phthalate Cure time 5 min to 10 min., opaque, thermosetting,
vacuum chamber which will allow the castable epoxy to be
minimal shrinkage, good resistance to etchants, high
poured into the mold after the chamber has been evacuated.
hardness
Vacuum pressure should be in the range of 630 mm to 760 mm
Epoxy Cure time 5 min to 10 min., opaque, thermosetting, (25 in. to 30 in.) of mercury.The vacuum should be maintained
minimal shrinkage, good resistance to etchants, high
for about two to ten min before allowing air into the chamber.
hardness, good impregnation
Low viscosity epoxy resins are recommended for best results
Phenolic Cure time 5 min to 10 min., opaque, thermosetting,
during vacuum infiltration and subsequent preparation of TSC
shrinkage during cure can leave crevice at specimen
specimens.
interface, degraded by hot etchants, moderate
8.3.3 Addition of fluorescent dyes (1) or other agents, such
hardness
A as Rhodamine B (2), that produce color response upon fluo-
These compounds often contain filler materials, such as glass fibers or mineral
particulate. rescent excitation or with crossed polarized illumination,
respectively, to the castable compound during mixing will aid
in the identification of impregnated porosity during micro-
TABLE 2 Characteristics of Castable Mounting Compounds
scopical examination.
Type of Compound Characteristics
8.3.4 Care should be used when handling castable mounting
Acrylic Cure time 8 min to 15 min, moderate shrinkage, low
compounds. Supplier’s instructions for the use and handling of
hardness, opaque
these materials should be followed.
Epoxy Cure time 1 h to 12 h, negligible shrinkage, low level of
9. Grinding and Polishing
heat generated during polymerization, moderate
hardness, transparent, low viscosity formula is best for
9.1 Due to the many different types of TSCs and substrate
vacuum impregnation
materials, grinding and polishing sequences will vary. Proper
Polyester Cure time 30 min to 60 min, high shrinkage, peak choice of polishing surface, lubricant, abrasive type and size,
curing temperature up to 120 °C (248 °F), moderate
time, force, polishing wheel speed and relative rotation will
hardness, transparent
produce accurate and consistent results. Some TSCs may
Polyester–Acrylic Cure time 8 to 15 min, negligible shrinkage, peak require specialized preparation techniques. However, many
curing temperature up to 120 °C (248 °F), high
coatings can be prepared on automatic and semi–automatic
hardness, opaque
polishing equipment by use of one of the three procedures
listed in Table 3, Table 4, and Table 5.
9.1.1 Useofautomaticandsemi–automaticpolishingequip-
ment has been found to reduce inconsistency in polished
specimens and is therefore required in the metallographic
8.1.5 All components of mounting compounds including
preparation for TSC specimens. These machines provide re-
resins and catalysts, as well as any dyes or colorants, should be
producibility in wheel speed, specimen position on the wheel,
handled in accordance with the manufacturer’s instructions.
applied pressure, relative rotation, and polishing time. Manual
Material Safety Data Sheets are available from the manufac-
grinding and polishing is not recommended because of the
turer.
inherent inconsistency and the sensitivity of these specimens to
8.2 Compression Mounting Compounds:
preparation technique. (3, 4, 5, 6)
8.2.1 Curing of compression mounting compounds is ac-
9.1.2 Most of the equipment for automatic and semi–auto-
complished by the use
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.