Standard Specification for Polypropylene Injection and Extrusion Materials Using ISO Protocol and Methodology

SCOPE
1.1 This specification covers polypropylene materials suitable for injection molding and extrusion. Polymers consist of polypropylene homopolymers, polypropylene copolymers, and polypropylene-elastomer compounds produced with or without the addition of impact modifiers (ethylene-propylene rubber, polyisobutylene rubber, and butyl rubber), colorants, stabilizers, lubricants, or reinforcements.
1.2 This specification allows for the use of those polypropylene materials that can be recycled, reconstituted, and reground, provided that the following conditions are met:
1.2.1 The requirements as stated in this specification and other ISO guidelines pertaining to these types of materials are met, and
1.2.2 The material has not been modified in any way to alter its conformance to food contact regulations or similar requirements.
1.3 The proportions of recycled, reconstituted, and regrind material used, as well as the nature and the amount of any contaminant, cannot be practically covered in this specification. It is the responsibility of the supplier and buyer of recycled, reconstituted, and regrind materials to ensure compliance.
Note 1—The properties included in this specification are those required to identify the compositions covered. There may be other requirements necessary to identify particular characteristics important to specific applications. These will be designated by using the suffixes given in Section 5.
1.4 The values stated in SI units are to be regarded as the standard.
1.5 The following precautionary caveat pertains only to the test methods portion, Section 13, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 2—This specification is similar to both ISO 1873-1 and ISO 1873-2, but to different degrees. This specification resembles ISO/DIS 1873-1-1994 in title only. The content is significantly different. This specification and ISO/DIS 1873-2-1994 differ in approach or detail; data obtained using either are technically equivalent.

General Information

Status
Historical
Publication Date
09-Jul-2003
Technical Committee
Current Stage
Ref Project

Relations

Buy Standard

Technical specification
ASTM D5857-03a - Standard Specification for Polypropylene Injection and Extrusion Materials Using ISO Protocol and Methodology
English language
19 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superceded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
Designation: D 5857 – 03a
Standard Specification for
Polypropylene Injection and Extrusion Materials Using ISO
1
Protocol and Methodology
This standard is issued under the fixed designation D 5857; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
INTRODUCTION
This material specification is intended to provide a call out system for polypropylene utilizing
specimen preparation procedures and test method based on ISO standards.
This specification is not intended for the determination of the suitability of performance of materials
in the final application. Selection of these materials is to be made by personnel with expertise in the
plastics field in which the environment, inherent properties of the materials, performance of the parts,
part design, manufacturing process, and economics are considered.
ments necessary to identify particular characteristics important to specific
1. Scope*
applications. These will be designated by using the suffixes given in
1.1 This specification covers polypropylene materials suit-
Section 5.
able for injection molding and extrusion. Polymers consist of
1.4 The properties included in this classification system are
polypropylene homopolymers, polypropylene copolymers, and
those required to identify the compositions covered. There may
polypropylene-elastomer compounds produced with or without
be other requirements necessary to identify particular charac-
the addition of impact modifiers (ethylene-propylene rubber,
teristics important to specialized applications. These may be
polyisobutylene rubber, and butyl rubber, and so forth), colo-
specified by using the suffixes as given in Section 5 and those
rants, stabilizers, lubricants, fillers, or reinforcements.
in Classification System D 4000.
1.2 This specification allows for the use of those polypro-
1.5 This classification system and specification are intended
pylene materials that can be recycled, reconstituted, and
to provide a means of calling out polypropylene materials used
reground, provided that the following conditions are met:
in the fabrication of end items or parts. It is not intended for the
1.2.1 The requirements as stated in this specification and
selection of materials. Material selection should be made by
other ISO guidelines pertaining to these types of materials are
those having expertise in the plastic field after careful consid-
met, and
eration of the design and the performance required of the part,
1.2.2 The material has not been modified in any way to alter
the environment to which it will be exposed, the fabrication
its conformance to food contact regulations or similar require-
process to be employed, the costs involved, and the inherent
ments.
properties of the material other than those covered by this
1.3 The proportions of recycled, reconstituted, and regrind
standard.
material used, as well as the nature and the amount of any
1.6 The values stated in SI units are to be regarded as the
contaminant, cannot be practically covered in this specifica-
standard.
tion. It is the responsibility of the supplier and buyer of
1.7 The following precautionary caveat pertains only to the
recycled, reconstituted, and regrind materials to ensure com-
test methods portion, Section 13, of this specification: This
pliance.
standard does not purport to address all of the safety concerns,
NOTE 1—The properties included in this specification are those re-
if any, associated with its use. It is the responsibility of the user
quired to identify the compositions covered. There may be other require-
of this standard to establish appropriate safety and health
practices and determine the applicability of regulatory limita-
tions prior to use.
1
This specification is under the jurisdiction of ASTM Committee D20 on
Plastics and is the direct responsibility of Subcommittee D20.15 on Thermoplastic
NOTE 2—This specification is similar to both ISO 1873-1 and ISO
Materials.
1873-2, but to different degrees. This specification resembles ISO 1873-1
Current edition approved July 10, 2003. Published October 2003. Originally
approved in 1996. Last previous edition approved in 2003 as D 5857 - 03.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
NOTICE: This standard has either been superceded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
D 5857 – 03a
in title only. The content is significant
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.