ASTM B619-05

Standard Specification for Welded Nickel and Nickel-Cobalt Alloy Pipe

SCOPE
1.1 This specification covers welded pipe of nickel and nickel-cobalt alloys (UNS N10001; UNS N10242; UNS N10665; UNS N12160; UNS N10624; UNS N10629; UNS N10675; UNS N10276; UNS N06455; UNS N06007; UNS N06975; UNS N08320; UNS N06002; UNS N06022; UNS N06035; UNS N06058; UNS N06059; UNS N06200; UNS N06985; UNS N06030; UNS R30556; UNS N08031; UNS N06230; UNS N06686; UNS N06210; and UNS R20033)* as shown in Table 1.
1.2 This specification covers pipe in Schedules 5S, 10S, 40S, and 80S through 8-in. nominal pipe size as set forth in ANSI B36.19 (see Table 2).
1.3 Two classes of pipe are covered as follows:
1.3.1 Class IAs welded and solution annealed or welded and sized and solution annealed.
1.3.2 Class IIWelded, cold worked, and solution annealed.
1.4 All pipe shall be furnished in the solution annealed and descaled condition. When atmosphere control is used, descaling is not necessary.
1.5 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

General Information

• Status: Historical
• Publication Date: 31-Jan-2005
• ICS: 23.040.15 - Non-ferrous metal pipes
• Technical Committee: B02 - Nonferrous Metals and Alloys
• Drafting Committee: B02.07 - Refined Nickel and Cobalt and Their Alloys

Relations

• Replaces: ASTM B619-04 - Standard Specification for Welded Nickel and Nickel-Cobalt Alloy Pipe
• Effective Date: 01-Feb-2005

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Please contact ASTM International (www.astm.org) for the latest information.
Designation: B 619 – 05
Standard Specification for
1
Welded Nickel and Nickel-Cobalt Alloy Pipe
This standard is issued under the fixed designation B 619; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (ϵ) indicates an editorial change since the last revision or reapproval.
1. Scope 2. Referenced Documents
2 3
1.1 This specification covers welded pipe of nickel and 2.1 ASTM Standards:
nickel-cobalt alloys (UNS N10001; UNS N10242; UNS B 775 Specification for General Requirements for Nickel
N10665; UNS N12160; UNS N10624; UNS N10629; UNS and Nickel Alloy Welded Pipe
N10675; UNS N10276; UNS N06455; UNS N06007; UNS B 899 Terminology Relating to Non-ferrous Metals and
N06975; UNS N08320; UNS N06002; UNS N06022; UNS Alloys
4
N06035; UNS N06058; UNS N06059; UNS N06200; UNS 2.2 ANSI Standards:
N06985; UNS N06030; UNS R30556; UNS N08031; UNS B36.19 Stainless Steel Pipe
N06230; UNS N06686; UNS N06210; and UNS R20033)* as B2.1 Pipe Threads
5
shown in Table 1. 2.3 ASME Boiler and Pressure Vessel Code
1.2 This specification covers pipe in Schedules 5S, 10S, Section IX Welding and Brazing Qualifications
40S, and 80S through 8-in. nominal pipe size and larger as set
3. Terminology
forth in ANSI B36.19 (see Table 2).
1.3 Two classes of pipe are covered as follows: 3.1 For definitions of terms used in this standard refer to
Terminology B 899B 899.
1.3.1 Class I—As welded and solution annealed or welded
and sized and solution annealed.
4. General Requirement
1.3.2 Class II—Welded, cold worked, and solution an-
4.1 Material furnished under this specification shall con-
nealed.
form to the applicable requirements of Specification
1.4 All pipe shall be furnished in the solution annealed and
B 775B 775 unless otherwise provided herein.
descaled condition. When atmosphere control is used, descal-
ing is not necessary.
5. Ordering Information
1.5 The values stated in inch-pound units are to be regarded
5.1 It is the responsibility of the purchaser to specify all
as the standard. The values given in parentheses are for
requirements that are necessary for material ordered under this
information only.
specification. Examples of such requirements include, but are
1.6 This standard does not purport to address all of the
not limited to the following:
safety concerns, if any, associated with its use. It is the
5.1.1 Alloy (Table 1),
responsibility of the user of this standard to become familiar
5.1.2 Class (see 1.3),
with all hazards including those identified in the appropriate
5.1.3 Quantity (feet or number of lengths),
Material Safety Data Sheet for this product/material as pro-
5.1.4 Size (nominal size or outside diameter and schedule
vided by the manufacturer, to establish appropriate safety and
number or average wall thickness),
health practices, and determine the applicability of regulatory
5.1.5 Length—Specify cut length or random,
limitations prior to use.
5.1.6 Certification— State if certification or a report of test
results is required,
1
This specification is under the jurisdiction of ASTM Committee B02 on
3
Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee For referenced ASTM standards, visit the ASTM website, www.astm.org, or
B02.07 on Refined Nickel and Cobalt and Their Alloys. contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
Current edition approved Feb. 1, 2005. Published February 2005. Originally Standards volume information, refer to the standard’s Document Summary page on
approved in 1981. Last previous edition approved in 2004 as B 619 – 04.
the ASTM website.
2
4
For ASME Boiler and Pressure Vessel Code applications see related Specifi-
Available fromAmerican National Standards Institute (ANSI), 25 W. 43rd St.,
cation SB-619 in Section II of that Code.
4th Floor, New York, NY 10036.
5
* New designation established in accordance with Practice E 527 and SAE Available from American Society of Mechanical Engineers (ASME), ASME
J1086, Practice for Numbering Metals and Alloys (UNS). International Headquarters, Three Park Ave., New York, NY 10016-5990.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Please contact ASTM International (www.astm.org) for the latest information.
B619–05
5.1.7 Purchaser Inspection—State which tests or inspec- 8.3.3 The bend test shall be acceptable if no cracks or other
1
tions are to be witnessed, defects exceeding ⁄8 in. (3 mm) in any direction be present in
5.1.8 Ends—Plain ends cut and de
...