ASTM F2764-11

Standard Specification for 30 to 60 in. [750 to 1500 mm] Polypropylene (PP) Triple Wall Pipe and Fittings for Non-Pressure Sanitary Sewer Applications

ABSTRACT
This specification covers requirements and test methods for triple wall polypropylene pipe and fittings with nominal inside diameters of 30 to 60 in. [750 to 1600 mm]. These requirements are intended to provide pipe and fittings suitable for underground use for non-pressure sanitary sewer systems. Pipe and fittings produced in accordance with this specification shall be installed in compliance with Practice D2321. Pipe and fittings with a interior wall, a exterior wall and an annular corrugated profile middle wall are covered by this specification.
SCOPE
1.1 This specification covers requirements and test methods for triple wall polypropylene pipe and fittings. The nominal inside diameters covered are 30 to 60 in. [750 to 1600 mm].
1.2 The requirements of this specification are intended to provide pipe and fittings suitable for underground use for non-pressure sanitary sewer systems. Pipe and fittings produced in accordance with this specification shall be installed in compliance with Practice D2321.
1.3 This specification covers pipe and fittings with an essentially smooth interior wall, an essentially smooth exterior wall and an annular corrugated profile middle wall (Fig. 1).
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.5 The following precautionary statement applies only to Section 7 of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

• Status: Historical
• Publication Date: 14-Feb-2011
• ICS: 91.140.80 - Drainage systems
• Technical Committee: F17 - Plastic Piping Systems
• Drafting Committee: F17.62 - Sewer

Relations

• Replaces: ASTM F2764-10a - Standard Specification for 30 to 60 in. [750 to 1500 mm] Polypropylene (PP) Triple Wall Pipe and Fittings for Non-Pressure Sanitary Sewer Applications
• Effective Date: 15-Feb-2011
• Replaced By: ASTM F2764-11a - Standard Specification for 30 to 60 in. [750 to 1500 mm] Polypropylene (PP) Triple Wall Pipe and Fittings for Non-Pressure Sanitary Sewer Applications
• Effective Date: 01-May-2011
• Referred By: ASTM F3202-19a - Standard Specification for Solid Wall Poly (Vinyl Chloride) PVC Fittings for Joining Corrugated Wall High Density Polyethylene (PE) and Polypropylene (PP) Piping
• Effective Date: 15-Feb-2011

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
An American National Standard
Designation: F2764 – 11
Standard Specification for
30 to 60 in. [750 to 1500 mm] Polypropylene (PP) Triple Wall
Pipe and Fittings for Non-Pressure Sanitary Sewer
1
Applications
This standard is issued under the fixed designation F2764; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope D790 Test Methods for Flexural Properties of Unreinforced
and Reinforced Plastics and Electrical Insulating Materials
1.1 This specification covers requirements and test methods
D792 Test Methods for Density and Specific Gravity (Rela-
for triple wall polypropylene pipe and fittings. The nominal
tive Density) of Plastics by Displacement
inside diameters covered are 30 to 60 in. [750 to 1600 mm].
D1238 Test Method for Melt Flow Rates of Thermoplastics
1.2 The requirements of this specification are intended to
by Extrusion Plastometer
provide pipe and fittings suitable for underground use for
D1505 Test Method for Density of Plastics by the Density-
non-pressure sanitary sewer systems. Pipe and fittings pro-
Gradient Technique
duced in accordance with this specification shall be installed in
D1600 Terminology for Abbreviated Terms Relating to
compliance with Practice D2321.
Plastics
1.3 This specification covers pipe and fittings with an
D2122 Test Method for Determining Dimensions of Ther-
essentially smooth interior wall, an essentially smooth exterior
moplastic Pipe and Fittings
wall and an annular corrugated profile middle wall (Fig. 1).
D2321 Practice for Underground Installation of Thermo-
1.4 The values stated in either SI units or inch-pound units
plastic Pipe for Sewers and Other Gravity-Flow Applica-
are to be regarded separately as standard. The values stated in
tions
each system may not be exact equivalents; therefore, each
D2412 Test Method for Determination of External Loading
system shall be used independently of the other. Combining
Characteristics of Plastic Pipe by Parallel-Plate Loading
values from the two systems may result in non-conformance
D2444 Test Method for Determination of the Impact Resis-
with the standard.
tance of Thermoplastic Pipe and Fittings by Means of a
1.5 The following precautionary statement applies only to
Tup (Falling Weight)
Section 7 of this specification. This standard does not purport
D2990 Test Methods for Tensile, Compressive, and Flex-
to address all of the safety concerns, if any, associated with its
ural Creep and Creep-Rupture of Plastics
use. It is the responsibility of the user of this standard to
D3212 Specification for Joints for Drain and Sewer Plastic
establish appropriate safety and health practices and deter-
Pipes Using Flexible Elastomeric Seals
mine the applicability of regulatory limitations prior to use.
D3895 Test Method for Oxidative-Induction Time of Poly-
2. Referenced Documents
olefins by Differential Scanning Calorimetry
2
D4101 Specification for Polypropylene Injection and Extru-
2.1 ASTM Standards:
sion Materials
A666 Specification for Annealed or Cold-Worked Auste-
D4218 Test Method for Determination of Carbon Black
nitic Stainless Steel Sheet, Strip, Plate, and Flat Bar
Content in Polyethylene Compounds By the Muffle-
D256 Test Methods for Determining the Izod Pendulum
Furnace Technique
Impact Resistance of Plastics
D4389 Specification for Finished Glass Fabrics Woven
D618 Practice for Conditioning Plastics for Testing
From Rovings
D638 Test Method for Tensile Properties of Plastics
D6992 Test Method for Accelerated Tensile Creep and
Creep-Rupture of Geosynthetic Materials Based on Time-
1
This specification is under the jurisdiction ofASTM Committee F17 on Plastic
Temperature Superposition Using the Stepped Isothermal
Piping Systems and is the direct responsibility of Subcommittee F17.62 on Sewer.
Method
Current edition approved Feb. 15, 2011. Published February 2011. Originally
F412 Terminology Relating to Plastic Piping Systems
approved in 2010. Last previous edition approved in 2010 as F2764–10a.
DOI:10.1520/D2764–11.
F477 SpecificationforElastomericSeals(Gaskets)forJoin-
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
ing Plastic Pipe
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
F2764 – 11
FIG. 1 Typical Triple Wall Pipe Profile
F2136 Test Method for Notched, Constant Ligament-Stress 4.1.5.1 Size and
...