ASTM D2665-08
(Specification)Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings
Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings
SCOPE
1.1 This specification covers requirements and test methods for materials, dimensions and tolerances, pipe stiffness, crush resistance, impact resistance, hydrostatic burst resistance, and solvent cement for poly(vinyl chloride) plastic drain, waste, and vent pipe and fittings. A form of marking is also included. Plastic which does not meet the material requirements specified in Section 5 is excluded. Installation procedures are given in the Appendix.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.
1.4 The following safety hazards caveat pertains only to the test methods portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
An American National Standard
Designation: D 2665 – 08
Standard Specification for
Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent
1
Pipe and Fittings
This standard is issued under the fixed designation D2665; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope D1784 SpecificationforRigidPoly(VinylChloride)(PVC)
Compounds and Chlorinated Poly(Vinyl Chloride)
1.1 This specification covers requirements and test methods
(CPVC) Compounds
for materials, dimensions and tolerances, pipe stiffness, crush
D2122 Test Method for Determining Dimensions of Ther-
resistance, impact resistance, hydrostatic burst resistance, and
moplastic Pipe and Fittings
solvent cement for poly(vinyl chloride) plastic drain, waste,
D2412 TestMethodforDeterminationofExternalLoading
and vent pipe and fittings.Aform of marking is also included.
Characteristics of Plastic Pipe by Parallel-Plate Loading
Plasticwhichdoesnotmeetthematerialrequirementsspecified
D2444 Test Method for Determination of the Impact Re-
in Section 5 is excluded. Installation procedures are given in
sistance ofThermoplastic Pipe and Fittings by Means of a
the Appendix.
Tup (Falling Weight)
1.2 Thevaluesstatedininch-poundunitsaretoberegarded
D2564 Specification for Solvent Cements for Poly(Vinyl
as standard. The values given in parentheses are mathematical
Chloride) (PVC) Plastic Piping Systems
conversions to SI units that are provided for information only
D3311 Specification for Drain, Waste, and Vent (DWV)
and are not considered standard.
Plastic Fittings Patterns
1.3 Thetextofthisspecificationreferencesnotes,footnotes,
D4396 SpecificationforRigidPoly(VinylChloride)(PVC)
and appendixes which provide explanatory material. These
and Chlorinated Poly(Vinyl Chloride) (CPVC) Com-
notesandfootnotes(excludingthoseintablesandfigures)shall
pounds for Plastic Pipe and Fittings Used in Nonpressure
not be considered as requirements of the specification.
Applications
1.4 The following safety hazards caveat pertains only to the
F402 Practice for Safe Handling of Solvent Cements,
test methods portion, Section 7, of this specification: This
Primers,andCleanersUsedforJoiningThermoplasticPipe
standard does not purport to address all of the safety concerns,
and Fittings
if any, associated with its use. It is the responsibility of the user
F412 Terminology Relating to Plastic Piping Systems
of this standard to establish appropriate safety and health
F1498 Specification for Taper Pipe Threads 60° for Ther-
practices and determine the applicability of regulatory limita-
moplastic Pipe and Fittings
tions prior to use.
F1866 Specification for Poly (Vinyl Chloride) (PVC) Plas-
2. Referenced Documents
tic Schedule 40 Drainage and DWV Fabricated Fittings
2
F2135 Specification for Molded Drain, Waste, and Vent
2.1 ASTM Standards:
(DWV) Short-Pattern Plastic Fittings
D618 Practice for Conditioning Plastics for Testing
D1599 Test Method for Resistance to Short-Time Hydrau-
3. Terminology
lic Pressure of Plastic Pipe, Tubing, and Fittings
3.1 Definitions—DefinitionsareinaccordancewithTermi-
D1600 Terminology for Abbreviated Terms Relating to
nology F412, and abbreviations are in accordance with Ter-
Plastics
minology D1600, unless otherwise specified.
1
4. Significance and Use
This specification is under the jurisdiction ofASTM Committee F17 on Plastic
Piping Systems and is the direct responsibility of Subcommittee F17.63 on DWV.
4.1 The requirements of this specification are intended to
CurrenteditionapprovedMay1,2008PublishedMay2008.Originallyapproved
provide pipe and fittings suitable for the drainage and venting
in 1968. Last previous edition approved in 2007 as D2665–07.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
of sewage and certain other liquid wastes.
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
NOTE 1—Industrial waste disposal lines should be installed only with
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. the specific approval of the cognizant building code authority since
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
D2665–08
chemicals not commonly found in drains and sewers and temperatures in
6.3.1.1 Pipe Stiffness (PS)—Three specimens shall be
excess of 180°F (82.2°C) may be encountered.
tested. If all three meet the PS requirement, the sample meets
NOTE 2—This speci
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
An American National Standard
Designation:D2665–07 Designation: D 2665 – 08
Standard Specification for
Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent
1
Pipe and Fittings
This standard is issued under the fixed designation D2665; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope
1.1 This specification covers requirements and test methods for materials, dimensions and tolerances, pipe stiffness, crush
resistance,impactresistance,hydrostaticburstresistance,andsolventcementforpoly(vinylchloride)plasticdrain,waste,andvent
pipe and fittings.Aform of marking is also included. Plastic which does not meet the material requirements specified in Section
5 is excluded. Installation procedures are given in the Appendix.
1.2The values stated in inch-pound units are to be regarded as the standard. The metric equivalents of inch-pound units given
in parentheses may be approximate.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.3 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes
and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.
1.4 Thefollowingsafetyhazardscaveatpertainsonlytothetestmethodsportion,Section7,ofthisspecification: This standard
does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this
standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
D618 Practice for Conditioning Plastics for Testing
D1599 Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings
D1600 Terminology for Abbreviated Terms Relating to Plastics
D1784 Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC)
Compounds
D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D2412 Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
D2444 TestMethodforDeterminationoftheImpactResistanceofThermoplasticPipeandFittingsbyMeansofaTup(Falling
Weight)
D2564 Specification for Solvent Cements for Poly(Vinyl Chloride) (PVC) Plastic Piping Systems
D3311 Specification for Drain, Waste, and Vent (DWV) Plastic Fittings Patterns
D4396 Specification for Rigid Poly(Vinyl Chloride) (PVC) and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds for
Plastic Pipe and Fittings Used in Nonpressure Applications
F402 Practice for Safe Handling of Solvent Cements, Primers, and Cleaners Used for JoiningThermoplastic Pipe and Fittings
F412 Terminology Relating to Plastic Piping Systems
F1498 Specification for Taper Pipe Threads 60 for Thermoplastic Pipe and Fittings
F1866 Specification for Poly (Vinyl Chloride) (PVC) Plastic Schedule 40 Drainage and DWV Fabricated Fittings
F2135 Specification for Molded Drain, Waste, and Vent (DWV) Short-Pattern Plastic Fittings
1
This specification is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.63 on DWV.
´2
Current edition approved March 1, 2007 Published March 2007. Originally approved in 1968. Last previous edition approved in 2004 as D2665–04a .
Current edition approved May 1, 2008 Published May 2008. Originally approved in 1968. Last previous edition approved in 2007 as D2665–07.
2
ForreferencedASTMstandards,visittheASTMwebsite,www.astm.org,orcontactASTMCustomerServiceatservice@astm.org.For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
D2665–08
3. Terminology
3.1 Definitions—DefinitionsareinaccordancewithTerminologyF412,andabbreviationsareinaccordancewithTerminology
D1600, unless otherwise sp
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.