ASTM C1763-19
(Test Method)Standard Test Method for Water Absorption by Immersion of Thermal Insulation Materials
Standard Test Method for Water Absorption by Immersion of Thermal Insulation Materials
SIGNIFICANCE AND USE
6.1 This test method provides a means of measuring the water absorption of flat specimens of thermal insulation materials under isothermal conditions as a result of direct immersion in liquid water. It is intended for quality control and product and material specifications.
6.2 The procedure to be used: A, B, or C as well as any exceptions shall be noted in material specifications citing this test method.
6.3 Repeatability has been established only for one type and size of material at one immersion duration.
Note 1: Specifications referring to this test method are encouraged to establish repeatability for specific materials, immersion duration, and dimensions for inclusion in this test method.
SCOPE
1.1 This test method determines the amount of water retained (excluding surface water) by flat specimens of thermal insulations after these materials have been fully immersed in liquid water for a prescribed time interval under isothermal conditions. This test method is intended to be used for the characterization of materials in the laboratory. It is not intended to simulate any particular environmental condition potentially encountered in building construction applications.
1.2 This test method does not address all the possible mechanisms of water intake and retention and related phenomena for thermal insulations. It relates only to those conditions outlined in 1.1. Determination of moisture accumulation in thermal insulations due to partial immersion, water vapor transmission, internal condensation, freeze-thaw cycling, or a combination of these effects requires different test procedures.
1.3 This test method does not address or attempt to quantify the drainage characteristics of materials.
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: C1763 − 19
Standard Test Method for
Water Absorption by Immersion of Thermal Insulation
1
Materials
This standard is issued under the fixed designation C1763; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 2. Material And Specimen Characteristics that can
Influence Results
1.1 This test method determines the amount of water re-
tained (excluding surface water) by flat specimens of thermal
2.1 The apparent water absorption measured by this test
insulations after these materials have been fully immersed in
method is dependent on the surface to volume ratio of the
liquid water for a prescribed time interval under isothermal
sample and time of immersion.As such, comparisons between
conditions. This test method is intended to be used for the
Procedures A, B, and, C cannot be made. Cracks in the
characterizationofmaterialsinthelaboratory.Itisnotintended
specimens and rough surfaces can increase the apparent water
to simulate any particular environmental condition potentially
absorption.
encountered in building construction applications.
2.2 Some materials tend to collect water on surfaces or to
1.2 This test method does not address all the possible
trap water in corners and, if not removed, will give incorrect
mechanisms of water intake and retention and related phenom-
results.
ena for thermal insulations. It relates only to those conditions
2.3 Materials that change or react with water can have
outlined in 1.1. Determination of moisture accumulation in
increased (or decreased) apparent water absorption and are not
thermal insulations due to partial immersion, water vapor
suitable for use with this method. 12.5.1 provides a method for
transmission, internal condensation, freeze-thaw cycling, or a
ensuring the specimen has not been physically or chemically
combination of these effects requires different test procedures.
altered in a way that would invalidate the measurement. Use
1.3 This test method does not address or attempt to quantify
this method in cases of dispute.
the drainage characteristics of materials.
3. Referenced Documents
1.4 The values stated in either SI units or inch-pound units
are to be regarded separately as standard. The values stated in 2
3.1 ASTM Standards:
each system are not necessarily exact equivalents; therefore, to
C168 Terminology Relating to Thermal Insulation
ensure conformance with the standard, each system shall be
C303 Test Method for Dimensions and Density of Pre-
used independently of the other, and values from the two
formed Block and Board–Type Thermal Insulation
systems shall not be combined.
C870 Practice for Conditioning of Thermal Insulating Ma-
1.5 This standard does not purport to address all of the
terials
safety concerns, if any, associated with its use. It is the
C1134 Test Method for Water Retention of Rigid Thermal
responsibility of the user of this standard to establish appro-
Insulations Following Partial Immersion
priate safety, health, and environmental practices and deter-
E177 Practice for Use of the Terms Precision and Bias in
mine the applicability of regulatory limitations prior to use.
ASTM Test Methods
1.6 This international standard was developed in accor-
E691 Practice for Conducting an Interlaboratory Study to
dance with internationally recognized principles on standard-
Determine the Precision of a Test Method
ization established in the Decision on Principles for the
Development of International Standards, Guides and Recom-
4. Terminology
mendations issued by the World Trade Organization Technical
4.1 Definitions—Terminology C168 applies to terms used in
Barriers to Trade (TBT) Committee.
this test method.
1
ThistestmethodisunderthejurisdictionofASTMCommitteeC16onThermal
Insulation and is the direct responsibility of Subcommittee C16.33 on Insulation
2
Finishes and Moisture. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved Oct. 15, 2019. Published November 2019. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 2014. Last previous edition approved in 2016 as C1763 – 16. DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/C1763-19. the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C1763 − 19
5. Summary of Test Method 8.2.1 Testspecimensshallbe152 63mmlong,89 63mm
1 1 1
wide, and 51 6 3 mm thick (6 6 ⁄8 in. long, 3 ⁄2 6 ⁄8 in. wide,
5.1 Test speci
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: C1763 − 16 C1763 − 19
Standard Test Method for
Water Absorption by Immersion of Thermal Insulation
1
Materials
This standard is issued under the fixed designation C1763; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This test method determines the amount of water retained (excluding surface water) by flat specimens of thermal insulations
after these materials have been fully immersed in liquid water for a prescribed time interval under isothermal conditions. This test
method is intended to be used for the characterization of materials in the laboratory. It is not intended to simulate any particular
environmental condition potentially encountered in building construction applications.
1.2 This test method does not address all the possible mechanisms of water intake and retention and related phenomena for
thermal insulations. It relates only to those conditions outlined in 1.1. Determination of moisture accumulation in thermal
insulations due to partial immersion, water vapor transmission, internal condensation, freeze-thaw cycling, or a combination of
these effects requires different test procedures.
1.3 This test method does not address or attempt to quantify the drainage characteristics of materials.
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each
system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used
independently of the other, and values from the two systems shall not be combined.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of
regulatory limitations prior to use.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Material And Specimen Characteristics that can Influence Results
2.1 The apparent water absorption measured by this test method is dependent on the surface to volume ratio of the sample and
time of immersion. As such, comparisons between Procedures A, B, and, C cannot be made. Cracks in the specimens and rough
surfaces can increase the apparent water absorption.
2.2 Some materials tend to collect water on surfaces or to trap water in corners and, if not removed, will give incorrect results.
2.3 Materials that change or react with water can have increased (or decreased) apparent water absorption and are not suitable
for use with this method. 13.5.112.5.1 provides a method for ensuring the specimen has not been physically or chemically altered
in a way that would invalidate the measurement. Use this method in cases of dispute.
3. Referenced Documents
2
3.1 ASTM Standards:
C168 Terminology Relating to Thermal Insulation
1
This test method is under the jurisdiction of ASTM Committee C16 on Thermal Insulation and is the direct responsibility of Subcommittee C16.33 on Insulation Finishes
and Moisture.
Current edition approved March 1, 2016Oct. 15, 2019. Published July 2016November 2019. Originally approved in 2014. Last previous edition approved in 20142016
as C1763 – 14.C1763 – 16. DOI: 10.1520/C1763-16.10.1520/C1763-19.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C1763 − 19
C303 Test Method for Dimensions and
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.