ASTM B523/B523M-12
(Specification)Standard Specification for Seamless and Welded Zirconium and Zirconium Alloy Tubes
Standard Specification for Seamless and Welded Zirconium and Zirconium Alloy Tubes
ABSTRACT
This specification covers the three grades of zirconium and zirconium alloy seamless and welded tubes. The tubes are furnished in three grades as Grade R60702 which is an unalloyed zirconium, Grade R60704 which is zirconium-tin alloy, and Grade R60705 which is zirconium-niobium alloy. Seamless tube shall be made by any seamless method. Welded tube shall be made from sheet or strip by an automatic arc-welding process or other method of welding. Filler metal shall not be used. The material shall conform to the required chemical compostion for zirconium, hafnium, iron, chromium, tin, hydrogen, nitrogen, carbon, niobium, and oxygen. The materials shall conform to the required tensile properties such as tensile strength, yield strength, and elongation.
SCOPE
1.1 This specification covers three grades of zirconium and zirconium alloy seamless and welded tubes.
1.2 Unless a single unit is used, for example corrosion mass gain in mg/dm2, the values stated in either inch-pound or SI units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. SI values cannot be mixed with inch-pound values.
1.3 The following precautionary caveat pertains only to the test methods portion of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:B523/B523M −12
StandardSpecification for
Seamless and Welded Zirconium and Zirconium Alloy
1
Tubes
This standard is issued under the fixed designation B523/B523M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope tion of Seamless and Welded Tubular Products, Titanium,
2 Austenitic Stainless Steel and Similar Alloys
1.1 This specification covers three grades of zirconium and
zirconium alloy seamless and welded tubes.
3. Terminology
1.2 Unless a single unit is used, for example corrosion mass
2 3.1 Definitions of Terms Specific to This Standard:
gain in mg/dm , the values stated in either inch-pound or SI
3.1.1 annealed, n—for purposes of this specification “
units are to be regarded separately as standard. The values
annealed” denotes material that exhibits a recrystallized grain
stated in each system are not exact equivalents; therefore, each
structure.
system must be used independently of the other. SI values
cannot be mixed with inch-pound values.
3.2 Lot Definitions:
1.3 The following precautionary caveat pertains only to the 3.2.1 tubes, n—a lot shall consist of a material of the same
test methods portion of this specification: This standard does size, shape, condition, and finish produced from the same ingot
not purport to address all of the safety concerns, if any, or powder blend by the same reduction schedule and the same
associated with its use. It is the responsibility of the user of this heat treatment parameters. Unless otherwise agreed between
standard to establish appropriate safety and health practices manufacturer and purchaser, a lot shall be limited to the
and determine the applicability of regulatory limitations prior product of an 8 h period for final continuous anneal, or to a
to use. single furnace load for final batch anneal.
2. Referenced Documents
4. Classification
3
2.1 ASTM Standards:
4.1 The tubes are furnished in three grades as follows:
A370 Test Methods and Definitions for Mechanical Testing
4.1.1 Grade R60702—Unalloyed zirconium.
of Steel Products
4.1.2 Grade R60704—Zirconium-tin alloy.
B551/B551M Specification for Zirconium and Zirconium
4.1.3 Grade R60705—Zirconium-niobium alloy.
Alloy Strip, Sheet, and Plate
B614 Practice for Descaling and Cleaning Zirconium and
5. Ordering Information
Zirconium Alloy Surfaces
E8 Test Methods for Tension Testing of Metallic Materials 5.1 Orders for material under this specification should
E29 Practice for Using Significant Digits in Test Data to
include the following information:
Determine Conformance with Specifications
5.1.1 Quantity (weight or number of pieces, or both),
E213 Practice for Ultrasonic Testing of Metal Pipe and
5.1.2 Name of material (zirconium seamless or welded
Tubing
tube),
E426 PracticeforElectromagnetic(Eddy-Current)Examina-
5.1.3 Dimensions (diameter, wall thickness as either aver-
age or minimum, lengths),
5.1.4 ASTM designation and year of issue,
1
This specification is under the jurisdiction ofASTM Committee B10 and is the
5.1.5 Grade number (see 4.1), and
direct responsibility of Subcommittee B10.02 on Zirconium and Hafnium.
Current edition approved May 15, 2012. Published June 2012. Originally
5.1.6 Additions to the specification, if required. See 6.3.1,
approved in 1970. Last previous edition approved in 2007 as B523/B523M – 07.
7.3, 10.1, 12.7.3, 14.1, and 15.1 for additional optional
DOI: 10.1520/B0523_B0523M-12.
2
requirements for the purchase order.
For ASME Boiler and Pressure Vessel Code Applications, see related Specifi-
cation SB–523 in Section II of that Code.
3
NOTE 1—A typical ordering description is as follows: 1000 pieces of
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
seamless zirconium tubes, 2 in. [50 mm] in outside diameter by 0.06 in.
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on [15 mm] in average wall thickness by 10 ft [3 m] in length, vacuum
the ASTM website. annealed, ASTM B523/B523M - 01, Grade R60702.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
B523/B523M−12
TABLE 2 Permissible Variation in Product Analysis Between
6. Materials and Manufacture
Different Laboratories
6.1 Seamless tube shall be made by any seamless method
Permissible Variation in Product
Element
that will yield a product meeting the requirements of this
Analysis, %
Hydrogen 0.002
specification.
Nitrogen 0.01
6.2 Welded tube shall be made from sheet or
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:B523/B523M–07 Designation: B523/B523M – 12
Standard Specification for
Seamless and Welded Zirconium and Zirconium Alloy
1
Tubes
This standard is issued under the fixed designation B523/B523M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
2
1.1 This specification covers three grades of zirconium and zirconium alloy seamless and welded tubes.
2
1.2 Unless a single unit is used, for example corrosion mass gain in mg/dm , the values stated in either inch-pound or SI units
are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore, each system must
be used independently of the other. SI values cannot be mixed with inch-pound values.
1.3 The following precautionary caveat pertains only to the test methods portion of this specification: This standard does not
purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to
establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
3
2.1 ASTM Standards:
A370 Test Methods and Definitions for Mechanical Testing of Steel Products
B551/B551M Specification for Zirconium and Zirconium Alloy Strip, Sheet, and Plate
B614 Practice for Descaling and Cleaning Zirconium and Zirconium Alloy Surfaces
E8 Test Methods for Tension Testing of Metallic Materials
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E213 Practice for Ultrasonic Testing of Metal Pipe and Tubing
E426 Practice for Electromagnetic (Eddy-Current) Examination of Seamless andWeldedTubular Products,Austenitic Stainless
Steel and Similar Alloys
3. Terminology
3.1 Definitions of Terms Specific to This Standard:
3.1.1 annealed, n—for purposes of this specification “ annealed” denotes material that exhibits a recrystallized grain structure.
3.2 Lot Definitions:
3.2.1 tubes, n—a lot shall consist of a material of the same size, shape, condition, and finish produced from the same ingot or
powder blend by the same reduction schedule and the same heat treatment parameters. Unless otherwise agreed between
manufacturer and purchaser, a lot shall be limited to the product of an 8 h period for final continuous anneal, or to a single furnace
load for final batch anneal.
4. Classification
4.1 The tubes are furnished in three grades as follows:
4.1.1 Grade R60702—Unalloyed zirconium.
4.1.2 Grade R60704—Zirconium-tin alloy.
4.1.3 Grade R60705—Zirconium-niobium alloy.
5. Ordering Information
5.1 Orders for material under this specification should include the following information:
1
This specification is under the jurisdiction of ASTM Committee B10 and is the direct responsibility of Subcommittee B10.02 on Zirconium and Hafnium.
Current edition approved June 1, 2007. Published July 2007. Originally approved in 1970. Last previous edition approved in 2006 as B523/B523M–06. DOI:
10.1520/B0523_B0523M-07.
Current edition approved May 15, 2012. Published June 2012. Originally approved in 1970. Last previous edition approved in 2007 as B523/B523M – 07. DOI:
10.1520/B0523_B0523M-12.
2
For ASME Boiler and Pressure Vessel Code Applications, see related Specification SB–523 in Section II of that Code.
3
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
B523/B523M – 12
5.1.1 Quantity (weight or number of pieces, or both),
5.1.2 Name of material (zirconium seamless or welded tube),
5.1.3 Dimensions (diameter, wall thickness as either average or minimum, lengths),
5.1.4 ASTM designation and year of issue,
5.1.5 Grade number (see 4.1), and
5.1.6 Additions to the specification, if required. See 6.3.1, 7.3, 10.1, 12.7.3, 14.1, and 15.1 for additional optional requirements
for the purchase order.
NOTE 1—Atypical ordering description is as follows: 1000 pieces of seamless zirconium tubes, 2 in. [50 mm] in outside diameter by 0.06 in. [15 mm]
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.