Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter

SCOPE
1.1 This specification covers polyethylene (PE) pipe made in thermoplastic pipe dimension ratios based on outside diameter and pressure rated for water (see ). Included are criteria for classifying PE plastic pipe materials and PE plastic pipe, a system of nomenclature for PE plastic pipe, and requirements and test methods for materials, workmanship, dimensions, sustained pressure, burst pressure, and environmental stress cracking. Methods of marking are also given.
1.2 All pipes produced under this specification may be used for the transport of water, industrial process liquids, effluents, slurries, municipal sewage, etc. The user should consult the manufacturer to determine whether the material being transported is compatible with polyethylene pipe and will not affect the service life beyond limits acceptable to the user.
1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
1.4 The following safety hazards caveat pertains only to the test methods portion, Section , of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
30-Nov-2003
Technical Committee
Drafting Committee
Current Stage
Ref Project

Relations

Buy Standard

Technical specification
ASTM D3035-03a - Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter
English language
7 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
An American National Standard
Designation: D 3035 – 03a
Standard Specification for
Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled
1
Outside Diameter
This standard is issued under the fixed designation D 3035; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope Extrusion Plastometer
D 1505 Test Method for Density of Plastics by the Density-
1.1 This specification covers polyethylene (PE) pipe made
Gradient Technique
in thermoplastic pipe dimension ratios based on outside diam-
D 1598 Test Method for Time-to-Failure of Plastic Pipe
eter and pressure rated for water (see Appendix X1). Included
Under Constant Internal Pressure
are criteria for classifying PE plastic pipe materials and PE
D 1599 TestMethodforShort-TimeHydraulicFailurePres-
plastic pipe, a system of nomenclature for PE plastic pipe, and
sure of Plastic Pipe, Tubing, and Fittings
requirements and test methods for materials, workmanship,
D 1600 Terminology for Abbreviated Terms Relating to
dimensions, sustained pressure, burst pressure, and environ-
Plastics
mental stress cracking. Methods of marking are also given.
D 1603 Test Method for Carbon Black in Olefin Plastics
1.2 All pipes produced under this specification may be used
D 2122 Test Method for Determining Dimensions of Ther-
for the transport of water, industrial process liquids, effluents,
moplastic Pipe and Fittings
slurries, municipal sewage, etc. The user should consult the
D 2290 Test Method for Apparent Tensile Strength of Ring
manufacturer to determine whether the material being trans-
or Tubular Plastics and Reinforced Plastics by Split Disk
ported is compatible with polyethylene pipe and will not affect
Method
the service life beyond limits acceptable to the user.
D 2837 Test Method for Obtaining Hydrostatic Design
1.3 The values stated in inch-pound units are to be regarded
Basis for Thermoplastic Pipe Materials
as the standard. The values given in parentheses are for
D 3350 Specification for Polyethylene Plastics Pipe and
information only.
Fittings Materials
1.4 The following safety hazards caveat pertains only to the
F 412 Terminology Relating to Plastic Piping Systems
test methods portion, Section 7, of this specification: This
2.2 NSF International Standards:
standard does not purport to address all of the safety concerns,
ANSI/NSF Standard No. 14 for Plastic Piping Components
if any, associated with its use. It is the responsibility of the user
3
and Related Materials
of this standard to establish appropriate safety and health
ANSI/NSF Standard No. 61 for Drinking Water System
practices and determine the applicability of regulatory limita-
3
Components—Health Effects
tions prior to use.
2.3 PPI Documents:
2
2. Referenced Documents TR-4 Listing of Hydrostatic Design Bases (HDB), Strength
Design Bases (SDB), Pressure Design Bases (PDB) and
2.1 ASTM Standards:
Minimum Required Strength (MRS) Ratings for Thermo-
D 618 Practice for Conditioning Plastics and Electrical
4
plastic Piping Materials or Pipe
Insulating Materials for Testing
TR-9 Recommended Design Factors for Thermoplastic
D 792 Test Method for Density and Specific Gravity (Rela-
4
Pressure Pipe
tive Density) of Plastics by Displacement
D 1238 Test Method for Flow Rates of Thermoplastics by
3. Terminology
3.1 Definitions—Definitions are in accordance with Termi-
1
nology F 412, and abbreviations are in accordance with Ter-
This specification is under the jurisdiction ofASTM Committee F17 on Plastic
Piping Systems and is the direct responsibility of Subcommittee F17.26 on Olefin
minology D 1600, unless otherwise specified.
Based Pipe.
Current edition approved Dec. 1, 2003. Published January 2004. Originally
approved in 1972. Last previous edition approved in 2003 as D 3035 – 03.
2 3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or Available from the National Sanitation Foundation, P.O. Box 1468,AnnArbor,
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM MI 48106.
4
Standards volume information, refer to the standard’s Document Summary page on Available from the Plastics Pipe Institute, Inc., 1825 Connecticut Ave., NW,
the ASTM website. Suite 680 Washington, DC 20009.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
D 3035 – 03a
TABLE 1 Specification D 3350 Cell Classifications for TABLE 2 Long-Term Property Requirements
Polyethylene Pipe Materials
PE Mater
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.