ASTM C1063-07
(Specification)Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster
Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster
SCOPE
1.1 This specification covers the minimum requirements for lathing and furring for the application of exterior and interior portland cement-based plaster as in Specification C 926 or Specification C 841.
1.2 Where a fire resistance rating is required for plastered assemblies and constructions, details of construction shall be in accordance with reports of fire tests of assemblies that have met the requirements of the fire rating imposed.
1.3 Where a specific degree of sound control is required for plastered assemblies and constructions, details of construction shall be in accordance with official reports of tests conducted in recognized testing laboratories in accordance with the applicable requirements of Test Method E 90.
1.4 The values stated in inch-pound units are to be regarded as the standard. The SI (metric) values given in parentheses are approximate and are provided for information purposes only.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: C 1063 – 07
Standard Specification for
Installation of Lathing and Furring to Receive Interior and
1
Exterior Portland Cement-Based Plaster
This standard is issued under the fixed designation C 1063; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope* C841 Specification for Installation of Interior Lathing and
Furring
1.1 This specification covers the minimum requirements for
C847 Specification for Metal Lath
lathing and furring for the application of exterior and interior
C926 Specification for Application of Portland Cement-
portland cement-based plaster as in Specification C926 or
Based Plaster
Specification C841.
C933 Specification for Welded Wire Lath
1.2 Where a fire resistance rating is required for plastered
C954 Specification for Steel Drill Screws for the Applica-
assembliesandconstructions,detailsofconstructionshallbein
tion of Gypsum Panel Products or Metal Plaster Bases to
accordance with reports of fire tests of assemblies that have
Steel Studs from 0.033 in. (0.84 mm) to 0.112 in. (2.84
met the requirements of the fire rating imposed.
mm) in Thickness
1.3 Where a specific degree of sound control is required for
C 1002 Specification for Steel Self-Piercing Tapping
plastered assemblies and constructions, details of construction
Screws for the Application of Gypsum Panel Products or
shallbeinaccordancewithofficialreportsoftestsconductedin
Metal Plaster Bases to Wood Studs or Steel Studs
recognized testing laboratories in accordance with the appli-
C1032 Specification for Woven Wire Plaster Base
cable requirements of Test MethodE90.
D1784 Specification for Rigid Poly(Vinyl Chloride) (PVC)
1.4 The values stated in inch-pound units are to be regarded
Compounds and Chlorinated Poly(Vinyl Chloride)
asthestandard.TheSI(metric)valuesgiveninparenthesesare
(CPVC) Compounds
approximate and are provided for information purposes only.
D4216 Specification for Rigid Poly(Vinyl Chloride) (PVC)
2. Referenced Documents and Related PVC and Chlorinated Poly(Vinyl Chloride)
2
(CPVC) Building Products Compounds
2.1 ASTM Standards:
E90 Test Method for Laboratory Measurement ofAirborne
A641/A641M SpecificationforZinc−Coated(Galvanized)
Sound Transmission Loss of Building Partitions and Ele-
Carbon Steel Wire
ments
A653/A653M Specification for Steel Sheet, Zinc-Coated
(Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed)
3. Terminology
by the Hot-Dip Process
3.1 Definitions—For definitions relating to Ceilings and
B69 Specification for Rolled Zinc
Walls, see TerminologyC11.
B221 Specification for Aluminum and Aluminum-Alloy
3.2 Definitions of Terms Specific to This Standard:
Extruded Bars, Rods, Wire, Profiles, and Tubes
3.2.1 hangers—wires or steel rods or straps used to support
C11 Terminology Relating to Gypsum and Related Build-
main runners for suspended ceilings beneath floor or roof
ing Materials and Systems
constructions.
3.2.2 inserts—devices embedded in concrete structural
1
This specification is under the jurisdiction of ASTM Committee C11 on
members to provide a loop or opening for attachment of
GypsumandRelatedBuildingMaterialsandSystemsandisthedirectresponsibility
hangers.
ofSubcommitteeC11.03onSpecificationsfortheApplicationofGypsumandOther
3.2.3 saddle tie—see Figs. 1 and 2.
Products in Assemblies.
3.2.4 self-furring—a metal plaster base manufactured with
Current edition approved Nov. 1, 2007. Published December 2007. Originally
approved in 1986. Last previous edition approved in 2006 as C1063–06.
evenly-spaced indentations that hold the body of the lath
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
1
approximately ⁄4 in. (6.4 mm) away from solid surfaces to
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
which it is applied.
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
*ASummary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
C 1063 – 07
6.2.1 General—All accessories shall have perforated or
expanded flanges or clips shaped to permit complete embed-
ment in the plaster, to provide means for accurate alignment,
and to secure attachment of the accessory to the underlying
surface.Accessoriesshallbedesignedtoreceiveapplicationof
the specified plaster thickness.
6.2.2 AccessoriesshallbefabricatedfromZincAlloy(99%
pure zinc), galvanized (zinc coat
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: C 1063 – 07
Standard Specification for
Installation of Lathing and Furring to Receive Interior and
1
Exterior Portland Cement-Based Plaster
This standard is issued under the fixed designation C 1063; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope*
1.1 This specification covers the minimum requirements for lathing and furring for the application of exterior and interior
portland cement-based plaster as in Specification C 926 or Specification C 841.
1.2 Where a fire resistance rating is required for plastered assemblies and constructions, details of construction shall be in
accordance with reports of fire tests of assemblies that have met the requirements of the fire rating imposed.
1.3 Where a specific degree of sound control is required for plastered assemblies and constructions, details of construction shall
be in accordance with official reports of tests conducted in recognized testing laboratories in accordance with the applicable
requirements of Test Method E 90.
1.4 The values stated in inch-pound units are to be regarded as the standard. The SI (metric) values given in parentheses are
approximate and are provided for information purposes only.
2. Referenced Documents
2
2.1 ASTM Standards:
A 641/A 641M Specification for ZincCoated (Galvanized) Carbon Steel Wire
A 653/A 653M Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the
Hot-Dip Process
B 69 Specification for Rolled Zinc
B 221 Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes
C 11 Terminology Relating to Gypsum and Related Building Materials and Systems
C 841 Specification for Installation of Interior Lathing and Furring
C 847 Specification for Metal Lath
C 926 Specification for Application of Portland Cement-Based Plaster
C 933 Specification for Welded Wire Lath
C 954 Specification for Steel Drill Screws for theApplication of Gypsum Panel Products or Metal Plaster Bases to Steel Studs
from 0.033 in. (0.84 mm) to 0.112 in. (2.84 mm) in Thickness
C 1002 Specification for Steel Self-Piercing Tapping Screws for the Application of Gypsum Panel Products or Metal Plaster
Bases to Wood Studs or Steel Studs
C 1032 Specification for Woven Wire Plaster Base
D 1784 Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC)
Compounds
D 4216 Specification for Rigid Poly(Vinyl Chloride) (PVC) and Related PVC and Chlorinated Poly(Vinyl Chloride) (CPVC)
Building Products Compounds
E 90 Test Method for Laboratory Measurement of Airborne Sound Transmission Loss of Building Partitions and Elements
3. Terminology
3.1 Definitions—For definitions relating to Ceilings and Walls, see Terminology C 11.
3.2 Definitions of Terms Specific to This Standard:
1
This specification is under the jurisdiction of ASTM Committee C11 on Gypsum and Related Building Materials and Systems and is the direct responsibility of
Subcommittee C11.03 on Specifications for the Application of Gypsum and Other Products in Assemblies.
Current edition approved Nov. 1, 2007. Published December 2007. Originally approved in 1986. Last previous edition approved in 2006 as C 1063 – 06.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*ASummary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
C 1063 – 07
3.2.1 hangers—wires or steel rods or straps used to support main runners for suspended ceilings beneath floor or roof
constructions.
3.2.2 inserts—devices embedded in concrete structural members to provide a loop or opening for attachment of hangers.
3.2.3 saddle tie—see Figs. 1 and 2.
3.2.4 self-furring—a metal plaster base manufactured with evenly-spaced indentations that hold the body of the lath
1
approximately ⁄4 in. (6.4 mm) away from solid surfaces to which it is applied.
3.2.5 framing member, n—studs, joist, runners (track), bridgin
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.