ASTM F806-99a(2017)
(Test Method)Standard Test Method for Compressibility and Recovery of Laminated Composite Gasket Materials
Standard Test Method for Compressibility and Recovery of Laminated Composite Gasket Materials
SIGNIFICANCE AND USE
3.1 This test method is designed to compare related laminated composite gasket materials under controlled conditions and their short-time compressibility and recovery at room temperature. It measures compressibility with a matched pair of opposing upper and lower penetrators which provide better precision and bias than methods using an upper penetrator and a lower anvil. It is difficult to prepare undistorted test specimens from laminated composite gasket materials which will lay flat on an anvil. Also, with many composites having rigid inner layers the load on the upper penetrator is distributed over the bottom anvil area resulting in a lower than actual compressibility reading. This test method may be used as a routine test method when agreed upon between the purchaser and the producer.
SCOPE
1.1 This test method covers determination of the short-time compressibility and recovery at room temperature of laminated composite gasket materials.
1.2 This test method is not intended as a test for compressibility under prolonged stress application, that is “creep,” or for recovery following such prolonged stress application, the inverse of which is generally referred to as “compression set.” Also, it is only intended for tests at room temperature.
1.3 The values stated in SI units are to be regarded as the standard. The inch-pound units given in parentheses are for information only.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: F806 − 99a (Reapproved 2017)
Standard Test Method for
Compressibility and Recovery of Laminated Composite
Gasket Materials
ThisstandardisissuedunderthefixeddesignationF806;thenumberimmediatelyfollowingthedesignationindicatestheyearoforiginal
adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.Asuperscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 3. Significance and Use
1.1 This test method covers determination of the short-time 3.1 This test method is designed to compare related lami-
compressibility and recovery at room temperature of laminated nated composite gasket materials under controlled conditions
composite gasket materials. and their short-time compressibility and recovery at room
temperature. It measures compressibility with a matched pair
1.2 This test method is not intended as a test for compress-
of opposing upper and lower penetrators which provide better
ibilityunderprolongedstressapplication,thatis“creep,”orfor
precision and bias than methods using an upper penetrator and
recovery following such prolonged stress application, the
a lower anvil. It is difficult to prepare undistorted test speci-
inverse of which is generally referred to as “compression set.”
mens from laminated composite gasket materials which will
Also, it is only intended for tests at room temperature.
lay flat on an anvil. Also, with many composites having rigid
1.3 The values stated in SI units are to be regarded as the
inner layers the load on the upper penetrator is distributed over
standard. The inch-pound units given in parentheses are for
the bottom anvil area resulting in a lower than actual com-
information only.
pressibility reading. This test method may be used as a routine
1.4 This standard does not purport to address all of the test method when agreed upon between the purchaser and the
safety concerns, if any, associated with its use. It is the
producer.
responsibility of the user of this standard to establish appro-
4. Apparatus
priate safety and health practices and determine the applica-
bility of regulatory limitations prior to use.
4.1 The testing machine shall consist of the following
1.5 This international standard was developed in accor-
components.
dance with internationally recognized principles on standard-
4.1.1 Penetrators—A matched pair of opposing steel cylin-
ization established in the Decision on Principles for the
ders (within 6 0.025 mm (0.001 in.)) specified for the type of
Development of International Standards, Guides and Recom-
material being tested, with the cylinder ends hardened and
mendations issued by the World Trade Organization Technical
ground. Penetrator diameters for various types of laminated
Barriers to Trade (TBT) Committee.
composite gasket materials are shown in Table 1.
4.1.2 Dial—An indicating dial, or dials, graduated in 0.025
2. Referenced Documents
mm (0.001 in.) to show the thickness of the specimen during
2.1 ASTM Standards: the test. Readings shall be estimated to the nearest 0.0025 mm
F104 Classification System for Nonmetallic Gasket Materi- (0.0001 in.).
als 4.1.3 Preload, shall include the weight of the penetrator
itself and added weights to give the value specified within 6
2.2 ASTM Adjuncts:
1 %. A 22.2-N (5-lbf) preload shall be used.
Testing Machine Drawings
4.1.4 Loading Device—A device for applying a specified
major load to the upper end of the penetrator, which may
This test method is under the jurisdiction ofASTM Committee F03 on Gaskets
consist of an arrangement of dead weights, a hydraulic
and is the direct responsibility of Subcommittee F03.20 on Mechanical Test
cylinder, an air cylinder, or any other device capable of
Methods.
applying the major load at a slow uniform rate and to an
CurrenteditionapprovedMay1,2017.PublishedJuly2017.Originallyapproved
in 1983. Last previous edition approved in 2009 as F806 – 99a (2009). DOI:
accuracy of 6 1 %. The major load shall be in addition to the
10.1520/F0806-99AR17.
specified preload. Major loads for various types of laminated
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
composite gasket materials are shown in Table 1.
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
3 4
Available from ASTM International Headquarters. Order Adjunct No. Alistofrecommendedsuppliers,bySubcommitteeF03.20,isavailablethrough
ADJF0806. Original adjunct produced in 1983. ASTM.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
F806 − 99a (2017)
TABLE 1 Conditioning and Test Loads for Laminated Composite Gasket Materials
NOTE 1—If the nonmetallic layers of the laminated composite are not all the same material, then the test loads may be as agreed upon between the
producer and user.
F104
Total Load (sum of Major Load
A
Type of Gasket Mate-
Identification
Proce- Penetrator Preload, Major Load,
and Preload)
rial in the Nonmetallic Conditioning Procedure
First Two
dure Diameter, mm (in.) N (lbf) N (lbf)
Numerals of Six-
Layers
N (lbf) MPa (psi)
Digit Number
A compressed asbestos F11, F12, 1hat100±2°C(212±3.6°F); 6.4 (0.252) 22.2 (5) 1090 (245) 1112 (250) 34.5 (5000)
sheet; asbestos beater F51, F52 cool in desiccator over anhydrous
sheet; flexible graphite calcium chloride 21 to 30°C (70
to 85°F)
H asbestos paper and F13 4 h at 100 ± 2°C (212± 3.6°F); 6.4 (0.252) 22.2 (5) 1090 (245) 1112 (250) 34.5 (5000)
millboard cool as in Procedure A
F cork composition, cork F21, F23 At least 46 h at 21 to 30°C (
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.