ASTM B249/B249M-18
(Specification)Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Rod, Bar, Shapes and Forgings
Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Rod, Bar, Shapes and Forgings
ABSTRACT
This specification establishes the general requirements common to wrought copper and copper alloy rods, bars, shapes, and forgings. Products shall be manufactured by hot working, cold working, or both, and finished by cold working, annealing, or heat treatment and straightening as identified necessary to meet the properties specified. Materials shall be sampled and prepared, then tested accordingly to examine their conformance to dimensional (mass, diameter, length, straightness, and edge contours), mechanical (tensile strength, Rockwell hardness, elongation, and hydrogen embrittlement), electrical resistivity, chemical composition, and grain size requirements. The products shall also meet performance requirements when subjected to residual stress, mercurous nitrate, ammonia vapor, and semiguided bend tests. In the event of conflict between this specification and the individual casting product specifications, the requirements of the casting specification shall take precedence.
SIGNIFICANCE AND USE
12.1 For the purpose of determining compliance with the specified limits for requirements of the properties listed in the following table and for dimensional tolerances, an observed value or a calculated value shall be rounded as indicated in accordance with the rounding method of Practice E29.
Property
Rounded Unit for Observed or
Calculated Value
Chemical composition
Hardness
nearest unit in the last right-hand
Electrical resistivity
significant digit used in expressing the
Electrical conductivity
limiting value
Tensile strength
nearest ksi [5 MPa]
Yield strength
Elongation:
nearest 1 %
Grain size:
Under 0.060 mm
nearest multiple of 0.005 mm
0.060 mm and over
nearest 0.01 mm
SCOPE
1.1 This specification2 establishes the general requirements common to wrought copper and copper alloy rod, bar, shapes, and forgings which shall apply to Specifications B16/B16M, B21/B21M, B98/B98M, B124/B124M, B138/B138M, B139/B139M, B140/B140M, B150/B150M, B151/B151M, B187/B187M, B196/B196M, B283/B283M, B301/B301M, B371/B371M, B411/B411M, B441, B453/B453M, B455, B570, B870, B927/B927M, B929, B967/B967M, and B974/B974M to the extent referenced therein.
1.2 The chemical composition, physical and mechanical properties, and all other requirements not included in this specification are prescribed in the product specification.
1.3 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.3.1 Within the text the SI values are given in brackets.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:B249/B249M −18
Standard Specification for
General Requirements for Wrought Copper and Copper-
1
Alloy Rod, Bar, Shapes and Forgings
This standard is issued under the fixed designation B249/B249M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope* 2. Referenced Documents
3
2
2.1 ASTM Standards:
1.1 This specification establishes the general requirements
B16/B16M Specification for Free-Cutting Brass Rod, Bar
common to wrought copper and copper alloy rod, bar, shapes,
and Shapes for Use in Screw Machines
and forgings which shall apply to Specifications B16/B16M,
B21/B21M Specification for Naval Brass Rod, Bar, and
B21/B21M, B98/B98M, B124/B124M, B138/B138M, B139/
Shapes
B139M, B140/B140M, B150/B150M, B151/B151M, B187/
B98/B98M Specification for Copper-SiliconAlloy Rod, Bar
B187M, B196/B196M, B283/B283M, B301/B301M, B371/
and Shapes
B371M, B411/B411M, B441, B453/B453M, B455, B570,
B124/B124M Specification for Copper and Copper Alloy
B870, B927/B927M, B929, B967/B967M, and B974/B974M
Forging Rod, Bar, and Shapes
to the extent referenced therein.
B138/B138M SpecificationforManganeseBronzeRod,Bar,
1.2 The chemical composition, physical and mechanical
and Shapes
properties, and all other requirements not included in this
B139/B139M Specification for Phosphor Bronze Rod, Bar,
specification are prescribed in the product specification.
and Shapes
1.3 Units—The values stated in either SI units or inch-
B140/B140M Specification for Copper-Zinc-Lead (Red
pound units are to be regarded separately as standard. The
Brass or Hardware Bronze) Rod, Bar, and Shapes
values stated in each system may not be exact equivalents;
B150/B150M Specification forAluminum Bronze Rod, Bar,
therefore,eachsystemshallbeusedindependentlyoftheother.
and Shapes
Combining values from the two systems may result in non-
B151/B151M Specification for Copper-Nickel-Zinc Alloy
conformance with the standard.
(Nickel Silver) and Copper-Nickel Rod and Bar
1.3.1 Within the text the SI values are given in brackets. B154 Test Method for Mercurous Nitrate Test for Copper
Alloys
1.4 This standard does not purport to address all of the
B187/B187M Specification for Copper, Bus Bar, Rod, and
safety concerns, if any, associated with its use. It is the
Shapes and General Purpose Rod, Bar, and Shapes
responsibility of the user of this standard to establish appro-
B193 Test Method for Resistivity of Electrical Conductor
priate safety, health, and environmental practices and deter-
Materials
mine the applicability of regulatory limitations prior to use.
B194 Specification for Copper-BerylliumAlloy Plate, Sheet,
1.5 This international standard was developed in accor-
Strip, and Rolled Bar
dance with internationally recognized principles on standard-
B196/B196M SpecificationforCopper-BerylliumAlloyRod
ization established in the Decision on Principles for the
and Bar
Development of International Standards, Guides and Recom-
B283/B283M Specification for Copper and Copper-Alloy
mendations issued by the World Trade Organization Technical
Die Forgings (Hot-Pressed)
Barriers to Trade (TBT) Committee.
B301/B301M Specification for Free-Cutting Copper Rod,
Bar, Wire, and Shapes
B371/B371M Specification for Copper-Zinc-Silicon Alloy
1
ThisspecificationisunderthejurisdictionofASTMCommitteeB05onCopper
Rod
and CopperAlloysandisthedirectresponsibilityofSubcommittee B05.02 on Rod,
Bar, Wire, Shapes and Forgings.
Current edition approved March 1, 2018. Published April 2018. Originally
3
approvedin1951.Lastpreviouseditionapprovedin2017asB249/B249M-17.DOI: For referenced ASTM standards, visit the ASTM website, www.astm.org, or
10.1520/B0249_B0249M-18. contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
2
For ASME Boiler and Pressure Vessel Code applications see related Specifi- Standards volume information, refer to the standard’s Document Summary page on
cations SB-249 in Section II of that Code. the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
B249/B249M−18
B411/B411M Specification for Copper-Nickel-SiliconAlloy E478 Test Methods for ChemicalAnalysis of CopperAlloys
Rod and Bar E581 Test Methods for Chemical Analysis of Manganese-
B441 Specification for Copper-Cobalt-Beryllium, Copper- Copper Alloys
5
Nickel-Beryllium, and Copper-Nickel-Lead-Beryllium 2.2 ASME Standard
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: B249/B249M − 17 B249/B249M − 18
Standard Specification for
General Requirements for Wrought Copper and Copper-
1
Alloy Rod, Bar, Shapes and Forgings
This standard is issued under the fixed designation B249/B249M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope*
2
1.1 This specification establishes the general requirements common to wrought copper and copper alloy rod, bar, shapes, and
forgings which shall apply to Specifications B16/B16M, B21/B21M, B98/B98M, B124/B124M, B138/B138M, B139/B139M,
B140/B140M, B150/B150M, B151/B151M, B187/B187M, B196/B196M, B283/B283M, B301/B301M, B371/B371M, B411/
B411M, B441, B453/B453M, B455, B570, B870, B927/B927M, B929, B967/B967M, and B974/B974M to the extent referenced
therein.
1.2 The chemical composition, physical and mechanical properties, and all other requirements not included in this specification
are prescribed in the product specification.
1.3 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated
in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values
from the two systems may result in non-conformance with the standard.
1.3.1 Within the text the SI values are given in brackets.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety safety, health, and healthenvironmental practices and determine the
applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
3
2.1 ASTM Standards:
B16/B16M Specification for Free-Cutting Brass Rod, Bar and Shapes for Use in Screw Machines
B21/B21M Specification for Naval Brass Rod, Bar, and Shapes
B98/B98M Specification for Copper-Silicon Alloy Rod, Bar and Shapes
B124/B124M Specification for Copper and Copper Alloy Forging Rod, Bar, and Shapes
B138/B138M Specification for Manganese Bronze Rod, Bar, and Shapes
B139/B139M Specification for Phosphor Bronze Rod, Bar, and Shapes
B140/B140M Specification for Copper-Zinc-Lead (Red Brass or Hardware Bronze) Rod, Bar, and Shapes
B150/B150M Specification for Aluminum Bronze Rod, Bar, and Shapes
B151/B151M Specification for Copper-Nickel-Zinc Alloy (Nickel Silver) and Copper-Nickel Rod and Bar
B154 Test Method for Mercurous Nitrate Test for Copper Alloys
B187/B187M Specification for Copper, Bus Bar, Rod, and Shapes and General Purpose Rod, Bar, and Shapes
B193 Test Method for Resistivity of Electrical Conductor Materials
B194 Specification for Copper-Beryllium Alloy Plate, Sheet, Strip, and Rolled Bar
1
This specification is under the jurisdiction of ASTM Committee B05 on Copper and Copper Alloys and is the direct responsibility of Subcommittee B05.02 on Rod,
Bar, Wire, Shapes and Forgings.
Current edition approved April 1, 2017March 1, 2018. Published April 2017April 2018. Originally approved in 1951. Last previous edition approved in 20162017 as
B249/B249M-16.-17. DOI: 10.1520/B0249_B0249M-17.10.1520/B0249_B0249M-18.
2
For ASME Boiler and Pressure Vessel Code applications see related Specifications SB-249 in Section II of that Code.
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
B249/B249M − 18
B196/B196M Specification for Copper-Beryllium Alloy Rod and Bar
B283/B283M Specification for Copper and Copper-Alloy Die Forgings (Hot-Pressed)
B301/B301M Specification for Free-Cutting Coppe
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.