ASTM A484/A484M-05a

Standard Specification for General Requirements for Stainless Steel Bars, Billets, and Forgings

SCOPE
1.1 This specification covers general requirements that shall apply to wrought stainless steel bars, shapes, forgings, and billets or other semi-finished material (except wire) for forging, under the latest revision of each of the following ASTM specifications: A 276, A 314, A 458, A 473, A 477, A 479/A 479M, A 564/A 564M, A 565, A 582/A 582M, A 638/A 638M, A 705/A 705M, and A 831/A 831M.
1.2 In the case of conflict between a requirement of a product specification and a requirement of this specification, the product specification shall prevail. In the case of conflict between a requirement of the product specification or a requirement of this specification and a more stringent requirement of the purchase order, the purchase order shall prevail. The purchase order requirements shall not take precedence if they, in any way, violate the requirements of the product specification or this specification; for example, by waiving a test requirement or by making a test requirement less stringent.
1.3 The requirements for introduction of new materials in specifications referencing this specification are given in .
1.4 General requirements for flat-rolled stainless steel products other than bar are covered in Specification A 480/A 480M.
1.5 General requirements for wire products in coils are covered in Specification A 555/A 555M.
1.6 The values stated in either inch-pound units or SI (metric) units are to be regarded separately as the standard; within the text and tables, the SI units are shown in [brackets]. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.
1.7 Unless the order specifies an "M" designation, the material shall be furnished to inch-pound units.

General Information

• Status: Historical
• Publication Date: 14-Sep-2005
• ICS: 77.140.20 - Stainless steels
• Technical Committee: A01 - Steel, Stainless Steel and Related Alloys
• Drafting Committee: A01.17 - Flat-Rolled and Wrought Stainless Steel

Relations

• Replaces: ASTM A484/A484M-05 - Standard Specification for General Requirements for Stainless Steel Bars, Billets, and Forgings
• Effective Date: 15-Sep-2005
• Replaced By: ASTM A484/A484M-06 - Standard Specification for General Requirements for Stainless Steel Bars, Billets, and Forgings
• Effective Date: 15-Mar-2006
• Referred By: ASTM A479/A479M-23a - Standard Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels
• Effective Date: 15-Sep-2005
• Referred By: ASTM F961-20 - Standard Specification for 35Cobalt-35Nickel-20Chromium-10Molybdenum Alloy Forgings for Surgical Implants (UNS R30035)
• Effective Date: 15-Sep-2005
• Referred By: ASTM A555/A555M-23 - Standard Specification for General Requirements for Stainless Steel Wire and Wire Rods
• Effective Date: 15-Sep-2005
• Referred By: ASTM A753-21 - Standard Specification for Wrought Nickel-Iron Soft Magnetic Alloys (UNS K94490, K94840, N14076, N14080)
• Effective Date: 15-Sep-2005
• Referred By: ASTM A314-19 - Standard Specification for Stainless Steel Billets and Bars for Forging
• Effective Date: 15-Sep-2005
• Referred By: ASTM F2581-12(2017) - Standard Specification for Wrought Nitrogen Strengthened 11Manganese-17Chromium-3Molybdenum Low-Nickel Stainless Steel Alloy Bar and Wire for Surgical Implants (UNS S29225)
• Effective Date: 15-Sep-2005
• Referred By: ASTM A182/A182M-23 - Standard Specification for Forged or Rolled Alloy and Stainless Steel Pipe Flanges, Forged Fittings, and Valves and Parts for High-Temperature Service
• Effective Date: 15-Sep-2005
• Referred By: ASTM A1069/A1069M-19 - Standard Specification for Laser and Laser Hybrid Welded Stainless Steel Bars, Plates, and Shapes
• Effective Date: 15-Sep-2005
• Referred By: ASTM A564/A564M-19a - Standard Specification for Hot-Rolled and Cold-Finished Age-Hardening Stainless Steel Bars and Shapes
• Effective Date: 15-Sep-2005
• Referred By: ASTM A705/A705M-23 - Standard Specification for Age-Hardening Stainless Steel Forgings
• Effective Date: 15-Sep-2005
• Referred By: ASTM F1376-92(2020) - Standard Guide for Metallurgical Analysis for Gas Distribution System Components (Withdrawn 2023)
• Effective Date: 15-Sep-2005
• Referred By: ASTM F1586-21 - Standard Specification for Wrought Nitrogen Strengthened 21Chromium—10Nickel—3Manganese—2.5Molybdenum Stainless Steel Alloy Bar for Surgical Implants (UNS S31675)
• Effective Date: 15-Sep-2005
• Referred By: ASTM A582/A582M-22 - Standard Specification for Free-Machining Stainless Steel Bars
• Effective Date: 15-Sep-2005

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: A 484/A 484M – 05a
Standard Specification for
General Requirements for Stainless Steel Bars, Billets, and
1
Forgings
This standard is issued under the fixed designationA 484/A 484M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope* 2. Referenced Documents
2 3
1.1 This specification covers general requirements that 2.1 ASTM Standards:
shall apply to wrought stainless steel bars, shapes, forgings, A 262 Practices for Detecting Susceptibility to Intergranu-
and billets or other semi-finished material (except wire) for lar Attack in Austenitic Stainless Steels
forging, under the latest revision of each of the following A 276 Specification for Stainless Steel Bars and Shapes
ASTM specifications: A 276, A 314, A 458, A 473, A 477, A 314 Specification for Stainless Steel Billets and Bars for
A 479/A 479M, A 564/A 564M, A 565, A 582/A 582M, Forging
A 638/A 638M, A 705/A 705M, and A 831/A 831M. A 370 Test Methods and Definitions for MechanicalTesting
1.2 In the case of conflict between a requirement of a of Steel Products
product specification and a requirement of this specification, A 458 Specification for Hot-Worked, Hot-Cold-Worked,
the product specification shall prevail. In the case of conflict and Cold-Worked Alloy Steel Bars for High Strength at
4
between a requirement of the product specification or a Elevated Temperature
requirement of this specification and a more stringent require- A 473 Specification for Stainless Steel Forgings
ment of the purchase order, the purchase order shall prevail. A 477 Specification for Hot-Worked, Hot-ColdWorked and
The purchase order requirements shall not take precedence if Cold-WorkedAlloy Steel Forgings and Forging Billets for
4
they, in any way, violate the requirements of the product High Strength at Elevated Temperatures
specification or this specification; for example, by waiving a A 479/A 479M Specification for Stainless Steel Bars and
test requirement or by making a test requirement less stringent. Shapes for Use in Boilers and Other Pressure Vessels
1.3 The requirements for introduction of new materials in A 480/A 480M Specification for General Requirements for
specifications referencing this specification are given inAnnex Flat-Rolled Stainless and Heat-Resisting Steel Plate,
A1. Sheet, and Strip
1.4 General requirements for flat-rolled stainless steel prod- A 555/A 555M Specification for General Requirements for
uctsotherthanbararecoveredinSpecificationA 480/A 480M. Stainless and Heat-Resisting Steel Wire and Wire Rods
1.5 General requirements for wire products in coils are A 564/A 564M Specification for Hot-Rolled and Cold-
covered in Specification A 555/A 555M. Finished Age-Hardening Stainless Steel Bars and Shapes
1.6 The values stated in either inch-pound units or SI A 565 Specification for Martensitic Stainless Steel Bars,
(metric) units are to be regarded separately as the standard; Forgings, and Forging Stock for High-Temperature Ser-
within the text and tables, the SI units are shown in [brackets]. vice
The values stated in each system are not exact equivalents; A 582/A 582M Specification for Free-Machining Stainless
therefore,eachsystemmustbeusedindependentlyoftheother. and Steel Bars
Combining values from the two systems may result in noncon- A 638/A 638M Specification for Precipitation Hardening
formance with the specification. Iron Base Superalloy Bars, Forgings, and Forging Stock
1.7 Unless the order specifies an “M” designation, the for High-Temperature Service
material shall be furnished to inch-pound units. A 700 Practices for Packaging, Marking, and Loading
Methods for Steel Products for Domestic Shipment
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel,
Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee
3
A01.17 on Flat-Rolled and Wrought Stainless Steel. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved Sept. 15, 2005. Published October 2005. Originally contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
approved in 1963. Last previous edition approved in 2005 as A 484/A 484M – 05. Standards volume information, refer to the standard’s Document Summary page on
2
For ASME Boiler and Pressure Vessel Code Applications, see related Specifi- the ASTM website.
4
cation SA-484/SA-484M in Section II of that code. Withdrawn.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Bo
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:A484/A484M–05 Designation: A 484/A 484M – 05a
Standard Specification for
General Requirements for Stainless Steel Bars, Billets, and
1
Forgings
This standard is issued under the fixed designationA 484/A 484M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope*
2
1.1 This specification covers general requirements that shall apply to wrought stainless steel bars, shapes, forgings, and billets
or other semi-finished material (except wire) for forging, under the latest revision of each of the following ASTM specifications:
A 276,A 314,A 458,A 473,A 477,A 479/A 479M,A 564/A 564M,A 565,A 582/A 582M,A 638/A 638M,A 705/A 705M, and
A 831/A 831M.
1.2 In the case of conflict between a requirement of a product specification and a requirement of this specification, the product
specification shall prevail. In the case of conflict between a requirement of the product specification or a requirement of this
specification and a more stringent requirement of the purchase order, the purchase order shall prevail. The purchase order
requirements shall not take precedence if they, in any way, violate the requirements of the product specification or this
specification; for example, by waiving a test requirement or by making a test requirement less stringent.
1.3 The requirements for introduction of new materials in specifications referencing this specification are given in Annex A1.
1.4 General requirements for flat-rolled stainless steel products other than bar are covered in Specification A 480/A 480M.
1.5 General requirements for wire products in coils are covered in Specification A 555/A 555M.
1.6 The values stated in either inch-pound units or SI (metric) units are to be regarded separately as the standard; within the
text and tables, the SI units are shown in [brackets]. The values stated in each system are not exact equivalents; therefore, each
system must be used independently of the other. Combining values from the two systems may result in nonconformance with the
specification.
1.7 Unless the order specifies an “M” designation, the material shall be furnished to inch-pound units.
2. Referenced Documents
3
2.1 ASTM Standards:
A 262 Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels
A 276 Specification for Stainless Steel Bars and Shapes
A 314 Specification for Stainless Steel Billets and Bars for Forging
A 370 Test Methods and Definitions for Mechanical Testing of Steel Products
A 458 Specification for Hot-Worked, Hot-Cold-Worked, and Cold-Worked Alloy Steel Bars for High Strength at Elevated
4
Temperature
A 473 Specification for Stainless Steel Forgings
A 477 Specification for Hot-Worked, Hot-Cold Worked and Cold-Worked Alloy Steel Forgings and Forging Billets for High
4
Strength at Elevated Temperatures
A 479/A 479M Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels
A 480/A 480M Specification for General Requirements for Flat-Rolled Stainless and Heat-Resisting Steel Plate, Sheet, and
Strip
A 555/A 555M Specification for General Requirements for Stainless and Heat-Resisting Steel Wire and Wire Rods
A 564/A 564M Specification for Hot-Rolled and Cold-Finished Age-Hardening Stainless Steel Bars and Shapes
1
This specification is under the jurisdiction ofASTM CommitteeA01 on Steel, Stainless Steel and RelatedAlloys and is the direct responsibility of SubcommitteeA01.17
on Flat-Rolled and Wrought Stainless Steel.
Current edition approved March 1,Sept. 15, 2005. Published MarchOctober 2005. Originally approved in 1963. Last previous edition approved in 20032005 as
A 484/A 484M – 03a5.
2
For ASME Boiler and Pressure Vessel Code Applications, see related Specification SA-484/SA-484M in Section II of that code.
3
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
4
Withdrawn.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ---------------
...