ASTM A580/A580M-98(2004)

Standard Specification for Stainless Steel Wire

SCOPE
1.1 This specification covers stainless steel wire, except the free-machining types. It includes round, square, octagon, hexagon, and shape wire in coils only for the more commonly used types of stainless steels for general corrosion resistance and high-temperature service. For bars in straightened and cut lengths, see Specifications A 276 or A 479/A 479M.
Note 1—For free-machining stainless wire, designed especially for optimum machinability, see Specification A 581/A 581M.
1.2 The values stated in either inch-pound units or SI (metric) units are to be regarded separately as standards; within the text and tables, the SI units are shown in [brackets]. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.
1.3 Unless the order specifies the applicable "M" specification designation, the material shall be furnished to the inch-pound units.

General Information

• Status: Historical
• Publication Date: 31-Aug-2004
• ICS: 77.140.65 - Steel wire, wire ropes and link chains
• Technical Committee: A01 - Steel, Stainless Steel and Related Alloys
• Drafting Committee: A01.17 - Flat-Rolled and Wrought Stainless Steel

Relations

• Replaces: ASTM A580/A580M-98 - Standard Specification for Stainless Steel Wire
• Effective Date: 01-Sep-2004
• Replaced By: ASTM A580/A580M-06 - Standard Specification for Stainless Steel Wire
• Effective Date: 01-Mar-2006
• Referred By: ASTM F1138-21 - Standard Specification for Spray Shields for Mechanical Joints
• Effective Date: 01-Sep-2004
• Referred By: ASTM C1861-23 - Standard Specification for Lathing and Furring Accessories, and Fasteners, for Interior and Exterior Portland Cement-Based Plaster
• Effective Date: 01-Sep-2004
• Referred By: ASTM A951/A951M-22 - Standard Specification for Steel Wire for Masonry Joint Reinforcement
• Effective Date: 01-Sep-2004
• Referred By: ASTM F1546-23 - Standard Specification for Fire Hose Nozzles
• Effective Date: 01-Sep-2004
• Referred By: ASTM A581/A581M-22a - Standard Specification for Free-Machining Stainless Steel Wire and Wire Rods
• Effective Date: 01-Sep-2004
• Referred By: ASTM F2332-06(2022) - Standard Specification for Annular Ball Bearings for Instruments and Precision Rotating Components
• Effective Date: 01-Sep-2004
• Referred By: ASTM F1603-17(2023) - Standard Specification for Kettles, Steam-Jacketed, 32 oz to 20 gal (1 to 75.7 L), Tilting, Table Mounted, Direct Steam, Gas and Electric Heated
• Effective Date: 01-Sep-2004
• Referred By: ASTM F1602-12(2023) - Standard Specification for Kettles, Steam-Jacketed, 20 to 200 gal (75.7 to 757 L), Floor or Wall Mounted, Direct Steam, Gas and Electric Heated
• Effective Date: 01-Sep-2004
• Referred By: ASTM A555/A555M-23 - Standard Specification for General Requirements for Stainless Steel Wire and Wire Rods
• Effective Date: 01-Sep-2004

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: A 580/A 580M – 98 (Reapproved 2004)
Standard Specification for
Stainless Steel Wire
This standard is issued under the fixed designationA 580/A 580M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope 2.2 Society of Automotive Engineers Standard:
J 1086 Numbering Metals and Alloys
1.1 This specification covers stainless steel wire, except the
free-machining types. It includes round, square, octagon,
3. Ordering Information
hexagon, and shape wire in coils only for the more commonly
3.1 It is the responsibility of the purchaser to specify all
used types of stainless steels for general corrosion resistance
requirements that are necessary for material ordered under this
and high-temperature service. For bars in straightened and cut
specification. Such requirements may include, but are not
lengths, see Specifications A 276 or A 479/A 479M.
limited to, the following:
NOTE 1—For free-machining stainless wire, designed especially for
3.1.1 Quantity (weight),
optimum machinability, see Specification A 581/A 581M.
3.1.2 Name of material (stainless steel),
1.2 The values stated in either inch-pound units or SI
3.1.3 Type or UNS designation (Table 1),
(metric) units are to be regarded separately as standards; within
3.1.4 Condition (4.1),
the text and tables, the SI units are shown in [brackets]. The
3.1.5 Finish (4.2),
values stated in each system are not exact equivalents; there-
3.1.6 Cross section (round, square, etc.),
fore, each system must be used independently of the other.
3.1.7 Applicable dimensions including size, thickness, and
Combining values from the two systems may result in noncon-
width.
formance with the specification.
3.1.8 ASTM designation A 580/A 580M and date of issue.
1.3 Unless the order specifies the applicable “M” specifica-
3.1.9 Coil diameter (inside or outside diameter, or both) and
tion designation, the material shall be furnished to the inch-
coil weight.
pound units.
3.1.10 Special requirements.
NOTE 2—Atypicalorderingdescriptionisasfollows:5000lb[2000kg]
2. Referenced Documents
Type 304, wire, annealed and cold drawn, ⁄2 in. [13 mm] round, ASTM
2.1 ASTM Standards:
Specification A 580/A 580M dated . End use: machined hydraulic
A 276 Specification for Stainless Steel Bars and Shapes
coupling parts.
A 370 Test Methods and Definitions for MechanicalTesting
4. Manufacture
of Steel Products
A 479/A 479M Specification for Stainless Steel Bars and
4.1 Condition (Table 2):
Shapes for Use in Boilers and Other Pressure Vessels
4.1.1 Condition A—Annealed as a final heat treatment.
A 555/A 555M Specification for General Requirements for
Material in ConditionAmay be given a final cold drawing for
Stainless Steel Wire and Wire Rods
size control or finish, or both, slightly raising tensile strength.
A 581/A 581M Specification for Free-Machining Stainless
4.1.2 Condition B—Cold worked to higher strength.
Steel Wire and Wire Rods
4.1.3 Condition T—Heat treated to an intermediate temper
E 527 Practice for Numbering Metals and Alloys (UNS)
generally by austenitizing, quenching, and tempering at a
relatively low temperature.
4.1.4 Condition H—Heat treated to a hard temper generally
This specification is under the jurisdiction of ASTM Committee A01 on Steel,
by austenitizing, quenching, and tempering at a relatively low
Stainless Steel, and RelatedAlloys and is the direct responsibility of Subcommittee
temperature.
A01.17 on Flat-Rolled and Wrought Stainless Steel.
Current edition approved Sept. 1, 2004. Published September 2004. Originally
4.2 Finish:
approved in 1967. Last previous edition approved in 1998 as A 580/A 580M – 98.
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on Available from Society of Automotive Engineers (SAE), 400 Commonwealth
the ASTM website. Dr., Warrendale, PA 15096-0001.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
A 580/A 580M – 98 (2004)
TABLE 1 Chemical Requirements
Composition, %
UNS
Manga- Phos- Sul-
Desig- Type
Carbon, Silicon,
A
nese, phorus, fur, Chromium Nickel Molybdenum Nitrogen Other Elements
nation B B
max max
B
max max max
Austenitic Grades
S20161 . 0.15 4.0–6.0 0.040 0.040 3.0–4.0 15.0–18.0 4.0–6.0 0.08–0.20
S20910 XM-19 0.06 4.0–6.0 0.040 0.030 1.00 20.5–23.5 11.5–13.5 1.50–3.00 0.20–0.40 Cb 0.10–0.30
V 0.10–0.30
S21400 XM-31 0.12 14.0–16.0 0.045 0.030 0.30–1.00 17.0–18.5 1.00 0.35 max
max
S21800 . 0.10 7.0–9.0 0.060 0.030 3.5–4.5 16.0–18.0 8.0–9.0 0.08–0.18
S21900 XM-10 0.08 8.0–10.0 0.060 0.030 1.00 19.0–21.5 5.5–7.5 0.15–0.40
S21904 XM-11 0.04 8.0–10.0 0.060 0.030 1.00 19.0–21.5 5.5–7.5 0.15–0.40
S24000 XM-29 0.08 11.5–14.5 0.060 0.030 1.00 17.0–19.0 2.3–3.7 0.20–0.40
S24100 XM-28 0.15 11.0–14.0 0.040 0.030 1.00 16.5–19.0 0.5–2.50 0.20–0.45
S28200 . 0.15 17.0–19.0 0.045 0.030 1.00 17.0–19.0 . 0.75–1.25 0.40–0.60 Cu 0.75–1.25
0.10 max
S30200 302 0.15 2.00 0.045 0.030 1.00 17.0–19.0 8.0–10.0 0.10 max
S30215 302B 0.15 2.00 0.045 0.030 2.00–3.00 17.0–19.0 8.0–10.0
S30400 304 0.08 2.00 0.045 0.030 1.00 18.0–20.0 8.0–10.5 0.10 max
C
S30403 304L 0.030 2.00 0.045 0.030 1.00 18.0–20.0 8.0–12.0 0.10 max
S30500 305 0.12 2.00 0.045 0.030 1.00 17.0–19.0 10.5–13.0
S30800 308 0.08 2.00 0.045 0.030 1.00 19.0–21.0 10.0–12.0
S30900 309 0.20 2.00 0.045 0.030 1.00 22.0–24.0 12.0–15.0
S30908 309S 0.08 2.00 0.045 0.030 1.00 22.0–24.0 12.0–15.0
S30940 309Cb 0.08 2.00 0.045 0.030 1.00 22.0–24.0 12.0–16.0 0.10 max Cb+Ta 103C min,
1.10 max
S31000 310 0.25 2.00 0.045 0.030 1.50 24.0–26.0 19.0–22.0
S31008 310S 0.08 2.00 0.045 0.030 1.50 24.0–26.0 19.0–22.0
S31400 314 0.25 2.00 0.045 0.030 1.50–3.00 23.0–26.0 19.0–22.0
S31600 316 0.08 2.00 0.045 0.030 1.00 16.0–18.0 10.0–14.0 2.00–3.00 0.10 max
C
S31603 316L 0.030 2.00 0.045 0.030 1.00 16.0–18.0 10.0–14.0 2.00–3.00 0.10 max
S31700 317 0.08 2.00 0.045 0.030 1.00 18.0–20.0 11.0–15.0 3.0–4.0 0.10 max
S32100 321 0.08 2.00 0.045 0.030 1.00 17.0–19.0 9.0–12.0 Ti 53Cmin
S34700 347 0.08 2.00 0.045 0.030 1.00 17.0–19.0 9.0–13.0 Cb+Ta 103Cmin
S34800 348 0.08 2.00 0.045 0.030 1.00 17.0–19.0 9.0–13.0 Cb+Ta 103Cmin
Ta 1.10 max
Co 0.20 max
Ferritic Grades
S40500 405 0.08 1.00 0.040 0.030 1.00 11.5–14.5 . Al 0.10–0.30
S40976 . 0.030 1.00 0.040 0.030 1.00 10.5–11.7 0
...