ASTM D6334-07
(Test Method)Standard Test Method for Sulfur in Gasoline by Wavelength Dispersive X-Ray Fluorescence
Standard Test Method for Sulfur in Gasoline by Wavelength Dispersive X-Ray Fluorescence
SIGNIFICANCE AND USE
Knowledge of the presence of sulfur in petroleum products, especially fuels, helps predict performance characteristics, potential corrosion problems, and vehicle emission levels. In addition, some regulatory agencies mandate reduced levels of sulfur in reformulated type gasolines.
SCOPE
1.1 This test method covers the quantitative determination of total sulfur in gasoline and gasoline-oxygenate blends. The Pooled Limit of Quantitation (PLOQ) was determined to be 15 mg/kg. Therefore, the practical range for this test method is from 15 to 940 mg/kg.
Note 1—This concentration range is based on that used in the interlaboratory round robin, which shows that the range of sulfur in the round robin samples was from 1.5 to 940 mg/kg; however, below 15 mg/kg, the reproducibility approaches 100 % of the concentration.
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitation prior to use.
1.3 The values stated in SI units are to be regarded as the standard. The preferred units are mg/kg sulfur.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D6334 − 07
StandardTest Method for
Sulfur in Gasoline by Wavelength Dispersive X-Ray
1
Fluorescence
This standard is issued under the fixed designation D6334; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* D5453Test Method for Determination of Total Sulfur in
Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel
1.1 This test method covers the quantitative determination
Engine Fuel, and Engine Oil by Ultraviolet Fluorescence
of total sulfur in gasoline and gasoline-oxygenate blends. The
D5842Practice for Sampling and Handling of Fuels for
PooledLimitofQuantitation(PLOQ)wasdeterminedtobe15
Volatility Measurement
mg/kg. Therefore, the practical range for this test method is
D5854Practice for Mixing and Handling of Liquid Samples
from 15 to 940 mg/kg.
of Petroleum and Petroleum Products
NOTE 1—This concentration range is based on that used in the
D6299Practice for Applying Statistical Quality Assurance
interlaboratory round robin, which shows that the range of sulfur in the
and Control Charting Techniques to Evaluate Analytical
round robin samples was from 1.5 to 940 mg/kg; however, below 15
Measurement System Performance
mg/kg, the reproducibility approaches 100% of the concentration.
D6792Practice for Quality System in Petroleum Products
1.2 This standard does not purport to address all of the
and Lubricants Testing Laboratories
safety concerns, if any, associated with its use. It is the
responsibility of the user of this standard to establish appro-
3. Summary of Test Method
priate safety and health practices and determine the applica-
3.1 The sample is placed in the X-ray beam, and the
bility of regulatory limitation prior to use.
intensity of the sulfur Kα line at 5.373 Å is measured. The
1.3 The values stated in SI units are to be regarded as the
intensity of a corrected background, measured at a recom-
standard. The preferred units are mg/kg sulfur.
mended wavelength of 5.190 Å, or if a rhodium tube is used,
5.437 Å, is subtracted from this intensity. The resultant net
2. Referenced Documents
counting rate is then compared to a previously prepared
2
2.1 ASTM Standards:
calibration curve or equation to obtain the concentration of
D2622Test Method for Sulfur in Petroleum Products by
sulfur in mg/kg. (Warning—Exposure to excessive quantities
Wavelength Dispersive X-ray Fluorescence Spectrometry
of X radiation is injurious to health.Therefore, it is imperative
D3210Test Method for Comparing Colors of Films from
that the operator avoid exposing any part of his or her person,
Water-Emulsion Floor Polishes
not only to primary X-rays, but also to secondary or scattered
D4045Test Method for Sulfur in Petroleum Products by
radiationthatmightbepresent.TheX-rayspectrometershould
Hydrogenolysis and Rateometric Colorimetry
be operated in accordance with the regulations of recommen-
D4057Practice for Manual Sampling of Petroleum and
dations governing the use of ionizing radiation.)
Petroleum Products
D4177Practice for Automatic Sampling of Petroleum and
4. Significance and Use
Petroleum Products
4.1 Knowledge of the presence of sulfur in petroleum
D4294Test Method for Sulfur in Petroleum and Petroleum
products, especially fuels, helps predict performance
Products by Energy Dispersive X-ray Fluorescence Spec-
characteristics,potentialcorrosionproblems,andvehicleemis-
trometry
sion levels. In addition, some regulatory agencies mandate
reduced levels of sulfur in reformulated type gasolines.
1
This test method is under the jurisdiction of ASTM Committee D02 on
5. Interferences
PetroleumProductsandLubricantsandisthedirectresponsibilityofSubcommittee
D02.03 on Elemental Analysis.
5.1 Fuels with compositions that vary from those specified
Current edition approved Dec. 1, 2007. Published January 2008. Originally
´1
in 9.1 may be analyzed with standards made from base
approved in 1962. Last previous edition approved in 2003 as D6334–98(2003) .
DOI: 10.1520/D6334-07.
materials that are of similar composition to minimize matrix
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
effects.
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
5.1.1 Fuels containing oxygenates may be analyzed using
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. standardspreparedwithsimilaramountsofthesameoxygenate
*A Summary of Changes section appears at the end of this standard
Copyright ©ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA19428-2959. United States
1
---------------------- Page: 1 -
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
AnAmerican National Standard
e1
Designation:D6334–98 (Reapproved 2003) Designation:D6334–07
Standard Test Method for
Sulfur in Gasoline by Wavelength Dispersive X-Ray
1
Fluorescence
This standard is issued under the fixed designation D 6334; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1
e NOTE—Warning notes were editorially moved into the standard text in August 2003.
1. Scope*
1.1 Thistestmethodcoversthequantitativedeterminationoftotalsulfuringasolineandgasoline-oxygenateblends.ThePooled
Limit of Quantitation (PLOQ) was determined to be 15 mg/kg. Therefore, the practical range for this test method is from 15 to
940 mg/kg.
NOTE 1—This concentration range is based on that used in the interlaboratory round robin, which shows that the range of sulfur in the round robin
samples was from 1.5 to 940 mg/kg; however, below 15 mg/kg, the reproducibility approaches 100 % of the concentration.
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitation prior to use.
1.3 The values stated in SI units are to be regarded as the standard. The preferred units are mg/kg sulfur.
2. Referenced Documents
2
2.1 ASTM Standards:
D 2622 Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-RayX-ray Fluorescence Spectrometry
D 3210 Test Method for Comparing Colors of Films from Water-Emulsion Floor Polishes
D 4045 Test Method for Sulfur in Petroleum Products by Hydrogenolysis and Rateometric Colorimetry
D 4057 Practice for Manual Sampling of Petroleum and Petroleum Products
D 4177 Practice for the Automatic Sampling of Petroleum and Petroleum Products
D 4294 Test Method for Sulfur in Petroleum and Petroleum Products by Energy-Dispersive X-RayX-ray Fluorescence
4
Spectroscopy Spectrometry
D 5453Test Method for the Determination of Total Sulfur in Light Hydrocarbons, Motor Fuels and Oils by Ultraviolet
Fluorescence Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel
Engine Fuel, and Engine Oil by Ultraviolet Fluorescence
D 5842 Practice for Sampling and Handling of Fuels for Volatility Measurement
5
D 5854Practice for Mixing and Handling of Liquid Samples of Petroleum and Petroleum Products Practice for Mixing and
Handling of Liquid Samples of Petroleum and Petroleum Products
D 6299 Practice for Applying Statistical Quality Assurance Techniques to Evaluate Analytical Measurement System
Performance
D 6792 Practice for Quality System in Petroleum Products and Lubricants Testing Laboratories
3. Summary of Test Method
3.1 The sample is placed in the X-ray beam, and the intensity of the sulfur Ka line at 5.373 Å is measured. The intensity of
a corrected background, measured at a recommended wavelength of 5.190 Å, or if a rhodium tube is used, 5.437 Å, is subtracted
fromthisintensity.Theresultantnetcountingrateisthencomparedtoapreviouslypreparedcalibrationcurveorequationtoobtain
the concentration of sulfur in mg/kg. (Warning—Exposure to excessive quantities of X radiation is injurious to health.Therefore,
it is imperative that the operator avoid exposing any part of his or her person, not only to primary X-rays, but also to secondary
1
This test method is under the jurisdiction ofASTM Committee D02 on Petroleum Products and Lubricants and is the direct responsibility of Subcommittee D02.03 on
Elemental Analysis.
Current edition approved May 10, 2003. Published August 2003. Originally approved in 1962. Last previous edition approved in 1998 as D6334–98.
e1
Current edition approved Dec. 1, 2007. Published January 2008. Originally approved in 1962. Last previous edition approved in 2003 as D 6334–98(2003) .
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
, Vol 05.01.volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard.
Copyright ©ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA19428-2959, United States.
1
---------------------- Page: 1 -----------
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.