ASTM D6938-10
(Test Method)Standard Test Method for In-Place Density and Water Content of Soil and Soil-Aggregate by Nuclear Methods (Shallow Depth)
Standard Test Method for In-Place Density and Water Content of Soil and Soil-Aggregate by Nuclear Methods (Shallow Depth)
SIGNIFICANCE AND USE
The test method described is useful as a rapid, nondestructive technique for in-place measurements of wet density and water content of soil and soil-aggregate and the determination of dry density.
The test method is used for quality control and acceptance testing of compacted soil and soil-aggregate mixtures as used in construction and also for research and development. The nondestructive nature allows repetitive measurements at a single test location and statistical analysis of the results.
Density—The fundamental assumptions inherent in the methods are that Compton scattering is the dominant interaction and that the material is homogeneous.
Water Content—The fundamental assumptions inherent in the test method are that the hydrogen ions present in the soil or soil-aggregate are in the form of water as defined by the water content derived from Test Methods D2216, and that the material is homogeneous. (See 5.2)
Note 1—The quality of the result produced by this standard test method is dependent on the competence of the personnel performing it, and the suitability of the equipment and facilities used. Agencies that meet the criteria of Practice D3740 are generally considered capable of competent and objective testing/sampling/inspection, and the like. Users of this standard are cautioned that compliance with Practice D3740 does not in itself assure reliable results. Reliable results depend on many factors; Practice D3740 provides a means of evaluating some of those factors.
SCOPE
1.1 This test method describes the procedures for measuring in-place density and moisture of soil and soil-aggregate by use of nuclear equipment. The density of the material may be measured by direct transmission, backscatter, or backscatter/air-gap ratio methods. Measurements for water (moisture) content are taken at the surface in backscatter mode regardless of the mode being used for density. It is the intent of this subcommittee that this standard replace D2922 and D3017.
1.1.1 For limitations see Section 5 on Interferences.
1.2 The total or wet density of soil and soil-aggregate is measured by the attenuation of gamma radiation where, in direct transmission, the source is placed at a known depth up to 300 mm (12 in.) and the detector (s) remains on the surface (some gauges may reverse this orientation); or in backscatter or backscatter/air-gap the source and detector(s) both remain on the surface.
1.2.1 The density of the test sample in mass per unit volume is calculated by comparing the detected rate of gamma radiation with previously established calibration data.
1.2.2 The dry density of the test sample is obtained by subtracting the water mass per unit volume from the test sample wet density (Section 11). Most gauges display this value directly.
1.3 The gauge is calibrated to read the water mass per unit volume of soil or soil-aggregate. When divided by the density of water and then multiplied by 100, the water mass per unit volume is equivalent to the volumetric water content. The water mass per unit volume is determined by the thermalizing or slowing of fast neutrons by hydrogen, a component of water. The neutron source and the thermal neutron detector are both located at the surface of the material being tested. The water content most prevalent in engineering and construction activities is known as the gravimetric water content, w, and is the ratio of the mass of the water in pore spaces to the total mass of solids, expressed as a percentage.
1.4 Two alternative procedures are provided.
1.4.1 Procedure A
describes the direct transmission method in which the gamma source rod extends through the base of the gauge into a pre-formed hole to a desired depth. The direct transmission is the preferred method.
1.4.2 Procedure B
involves the use of a dedicated backscatter gauge or the source rod in the backscatter position. This places the gamma and neutron sources and the detectors in the...
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D6938 − 10
StandardTest Method for
In-Place Density and Water Content of Soil and Soil-
1
Aggregate by Nuclear Methods (Shallow Depth)
This standard is issued under the fixed designation D6938; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* ratio of the mass of the water in pore spaces to the total mass
of solids, expressed as a percentage.
1.1 Thistestmethoddescribestheproceduresformeasuring
1.4 Two alternative procedures are provided.
in-place density and moisture of soil and soil-aggregate by use
1.4.1 Procedure A describes the direct transmission method
of nuclear equipment. The density of the material may be
inwhichthegammasourcerodextendsthroughthebaseofthe
measured by direct transmission, backscatter, or backscatter/
gauge into a pre-formed hole to a desired depth. The direct
air-gap ratio methods. Measurements for water (moisture)
transmission is the preferred method.
content are taken at the surface in backscatter mode regardless
1.4.2 Procedure B involves the use of a dedicated backscat-
of the mode being used for density. It is the intent of this
ter gauge or the source rod in the backscatter position. This
subcommittee that this standard replace D2922 and D3017.
places the gamma and neutron sources and the detectors in the
1.1.1 For limitations see Section 5 on Interferences.
same plane.
1.2 The total or wet density of soil and soil-aggregate is
1.5 SI Units—The values stated in SI units are to be
measured by the attenuation of gamma radiation where, in
regarded as the standard. The values in inch-pound units (ft –
directtransmission,thesourceisplacedataknowndepthupto
lb units) are provided for information only.
300 mm (12 in.) and the detector (s) remains on the surface
(somegaugesmayreversethisorientation);orinbackscatteror
1.6 All observed and calculated values shall conform to the
backscatter/air-gap the source and detector(s) both remain on
guideforsignificantdigitsandroundingestablishedinPractice
the surface.
D6026.
1.2.1 Thedensityofthetestsampleinmassperunitvolume 1.6.1 Theproceduresusedtospecifyhowdataarecollected,
is calculated by comparing the detected rate of gamma radia- recorded, and calculated in this standard are regarded as the
tion with previously established calibration data. industry standard. In addition, they are representative of the
significant digits that should generally be retained. The proce-
1.2.2 The dry density of the test sample is obtained by
dures used do not consider material variation, purpose for
subtracting the water mass per unit volume from the test
obtaining the data, special purpose studies, or any consider-
sample wet density (Section 11). Most gauges display this
ations for the user’s objectives; and it is common practice to
value directly.
increase or reduce significant digits of reported data to be
1.3 The gauge is calibrated to read the water mass per unit
commensuratewiththeseconsiderations.Itisbeyondthescope
volume of soil or soil-aggregate. When divided by the density
of this standard to consider significant digits used in analysis
of water and then multiplied by 100, the water mass per unit
methods for engineering design.
volume is equivalent to the volumetric water content. The
1.7 This standard does not purport to address all of the
water mass per unit volume is determined by the thermalizing
safety concerns, if any, associated with its use. It is the
orslowingoffastneutronsbyhydrogen,acomponentofwater.
responsibility of the user of this standard to establish appro-
The neutron source and the thermal neutron detector are both
priate safety and health practices and determine the applica-
located at the surface of the material being tested. The water
bility of regulatory limitations prior to use.
content most prevalent in engineering and construction activi-
ties is known as the gravimetric water content, w, and is the
2. Referenced Documents
2
2.1 ASTM Standards:
1
ThistestmethodisunderthejurisdictionofASTMCommitteeD18onSoiland
Rock and is the direct responsibility of Subcommittee D18.08 on Special and
2
Construction Control Tests. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved May 1, 2010. Published June 2010. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 2006. Last previous edition approved in 2008 as D6938–08a. DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/D6938-10. the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM Inter
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:D6938–08a Designation:D6938–10
Standard Test Method for
In-Place Density and Water Content of Soil and Soil-
1
Aggregate by Nuclear Methods (Shallow Depth)
This standard is issued under the fixed designation D6938; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This test method describes the procedures for measuring in-place density and moisture of soil and soil-aggregate by use of
nuclear equipment. The density of the material may be measured by direct transmission, backscatter, or backscatter/air-gap ratio
methods. Measurements for water (moisture) content are taken at the surface in backscatter mode regardless of the mode being
used for density. It is the intent of this subcommittee that this standard replace D2922 and D3017.
1.1.1 For limitations see Section 5 on Interferences.
1.2 The total or wet density of soil and soil-aggregate is measured by the attenuation of gamma radiation where, in direct
transmission, the source is placed at a known depth up to 300 mm (12 in.) and the detector (s) remains on the surface (some gauges
may reverse this orientation); or in backscatter or backscatter/air-gap the source and detector(s) both remain on the surface.
1.2.1 The density of the test sample in mass per unit volume is calculated by comparing the detected rate of gamma radiation
with previously established calibration data.
1.2.2 The dry density of the test sample is obtained by subtracting the water mass per unit volume from the test sample wet
density (Section 11). Most gauges display this value directly.
1.3The1.3 The gauge is calibrated to read the water mass per unit volume of soil or soil-aggregate.When divided by the density
of water and then multiplied by 100, the water mass per unit volume is equivalent to the volumetric water content.The water mass
per unit volume is determined by the thermalizing or slowing of fast neutrons by hydrogen, a component of water. The neutron
source and the thermal neutron detector are both located at the surface of the material being tested. The water content most
prevalent in engineering and construction activities is known as the gravimetric water content, w, and is the ratio of the mass of
the water in pore spaces to the total mass of solids, expressed as a percentage.
1.4 Two alternative procedures are provided.
1.4.1 Procedure A describes the direct transmission method in which the gamma source rod extends through the base of the
gauge into a pre-formed hole to a desired depth. The direct transmission is the preferred method.
1.4.2 Procedure B involves the use of a dedicated backscatter gauge or the source rod in the backscatter position. This places
the gamma and neutron sources and the detectors in the same plane.
1.5 SI Units—The values stated in SI units are to be regarded as the standard. The values in inch-pound units (ft – lb units) are
provided for information only.
1.6 All observed and calculated values shall conform to the guide for significant digits and rounding established in Practice
D6026.
1.6.1 The procedures used to specify how data are collected, recorded, and calculated in this standard are regarded as the
industry standard. In addition, they are representative of the significant digits that should generally be retained. The procedures
used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the user’s
objectives; and it is common practice to increase or reduce significant digits of reported data to be commensurate with these
considerations.Itisbeyondthescopeofthisstandardtoconsidersignificantdigitsusedinanalysismethodsforengineeringdesign.
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
1
ThistestmethodisunderthejurisdictionofASTMCommitteeD18onSoilandRockandisthedirectresponsibilityofSubcommitteeD18.08onSpecialandConstruction
Control Tests.
Current edition approved JuneMay 1, 2008.2010. Published June 2008.2010. Originally approved in 2006. Last previous edition approved in 2008 as
D6938–08.D6938–08a. DOI: 10.1520/D6938-08A.10.1520/D6938-10.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.