ASTM C36/C36M-01

Standard Specification for Gypsum Wallboard

SCOPE
1.1 This specification covers gypsum wallboard which is designed to be used for walls, ceilings, or partitions and affords a surface suitable to receive decoration.  
Note 1--Specification C840 contains application procedures for gypsum wallboard.
1.2 The values stated in either inch-pound or SI (metric) units are to be regarded as standard. Within the text, the SI units are shown in brackets. The values stated in each system shall be used independent of the other. Values from the two systems shall not be combined..
1.3 The text of this standard references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.

General Information

• Status: Historical
• Publication Date: 09-May-2001
• ICS: 91.100.10 - Cement. Gypsum. Lime. Mortar
• Technical Committee: C11 - Gypsum and Related Building Materials and Systems
• Drafting Committee: C11.01 - Specifications and Test Methods for Gypsum Products

Relations

• Replaces: ASTM C36/C36M-99e1 - Standard Specification for Gypsum Wallboard
• Effective Date: 10-May-2001
• Replaced By: ASTM C36/C36M-03 - Standard Specification for Gypsum Wallboard
• Effective Date: 01-Oct-2003
• Referred By: ASTM C11-23 - Standard Terminology Relating to Gypsum and Related Building Materials and Systems
• Effective Date: 10-May-2001

Standards Content (Sample)

NOTICE: This standard has either been superceded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
Designation: C 36/C 36M – 01
Standard Specification for
1
Gypsum Wallboard
This standard is issued under the fixed designation C 36/C 36M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope * E 96 Test Methods for Water Vapor Transmission of Mate-
4
rials
1.1 This specification covers gypsum wallboard which is
E 119 Test Methods for Fire Tests of Building Construction
designed to be used for walls, ceilings, or partitions and affords
3
and Materials
a surface suitable to receive decoration.
NOTE 1—Specification C 840 contains application procedures for gyp- 3. Terminology
sum wallboard.
3.1 Definitions of terms shall be in accordance with Termi-
1.2 The values stated in either inch-pound or SI (metric)
nology C 11.
units are to be regarded separately as standard. Within the text,
4. Materials and Manufacture
the SI units are shown in brackets. The values stated in each
system shall be used independent of the other. Values from the 4.1 Gypsum wallboard shall consist of a noncombustible
two systems shall not be combined.
core, essentially gypsum, surfaced with paper bonded to the
1.3 The text of this standard references notes and footnotes core.
that provide explanatory material. These notes and footnotes
4.2 Foil-backed gypsum wallboard shall consist of gypsum
(excluding those in tables and figures) shall not be considered wallboard with a layer of aluminum foil laminated to the back
as requirements of the standard.
surface.
4.3 Gypsum wallboard, type X (special fire-resistant) des-
2. Referenced Documents
ignates gypsum wallboard complying with this specification
5
2.1 ASTM Standards:
that provides not less than 1 h fire-resistance for boards ⁄8 in.
3 1
C 11 Terminology Relating to Gypsum and Related Build-
[15.9 mm] thick or ⁄4 h fire-resistance for boards ⁄2 in. [12.7
2
ing Materials and Systems
mm] thick, applied parallel with and on each side of load
C 473 Test Methods for Physical Testing of Gypsum Panel
bearing 2 3 4 wood studs spaced 16 in. [406 mm] o.c. with 6d
2
7
Products
coated nails, 1 ⁄8 in. [48 mm] long, 0.0915 in. [2.32 mm]
1
C 645 Specification for Nonstructural Steel Framing Mem-
diameter shank, ⁄4 in. [6.4 mm] diameter heads, spaced 7 in.
2
bers
[178 mm] o.c. with wallboard joints staggered 16 in. [406 mm]
C 840 Specification for Application and Finishing of Gyp-
on each side of the partition and tested in accordance with the
2
sum Wallboard
requirements of Test Method E 119.
C 1264 Specification for Sampling, Inspection, Rejection,
NOTE 2—Consult producers for independent test data on assembly
Certification, Packaging, Marking, Shipping, Handling,
details and fire resistance classifications for other types of construction.
2
and Storage of Gypsum Board
See fire test reports, or listings from recognized fire testing laboratories,
E 84 Test Method for Surface Burning Characteristics of
for assembly particulars, materials, and classifications.
3
Building Materials
4.4 Gypsum wallboard shall have a flame spread index of
not more than 25 when tested in accordance with Test Method
E 84.
5. Physical Properties
5.1 Specimens shall be taken from the samples obtained in
1
This specification is under the jurisdiction of ASTM Committee C11 on
accordance with Specification C 1264.
Gypsum and Related Building Materials and Systems and is the direct responsibility
of Subcommittee C11.01 on Specifications and Test Methods for Gypsum Products.
5.2 Specimens shall be tested in accordance with Test
Current edition approved May 10, 2001. Published August 2001. Originally
Methods C 473.
e1
published as C 36 – 21 T. Last previous edition C 36/C 36M – 99 .
2
Annual Book of ASTM Standards, Vol 04.01.
3 4
Annual Book of ASTM Standards, Vol 04.07. Annual Book of ASTM Standards, Vol 04.06.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
NOTICE: This standard has either been superceded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
C 36/C 36M
5.2.1 Flexural Strength—The specimens shall be tested face 6. Dimensions and Tolerances
up and face down. The average breaking load shall be not less
6.1 Specimens shall be taken from the samples obtained in
than the following:
accordance with Specification C 1264.
Method A Method B
6.2 Thickness, width, length, and end squareness shall
...