ASTM B733-04(2014)
(Specification)Standard Specification for Autocatalytic (Electroless) Nickel-Phosphorus Coatings on Metal
Standard Specification for Autocatalytic (Electroless) Nickel-Phosphorus Coatings on Metal
ABSTRACT
This specification establishes the requirements for autocatalytic (electroless) nickel-phosphorus coatings applied from acidic aqueous solutions to metallic products for use in engineering functions operating at elevated temperatures. The coatings covered here are alloys of nickel and phosphorus produced by self-sustaining autocatalytic chemical reduction with hypophosphite. The coatings are grouped into the following classification systems: types, which are based on the general composition with respect to phosphorus; service condition numbers, which are based on the severity of exposure to which the coating is intended to perform and the corresponding minimum thickness that will provide satisfactory performance; and post heat treatment class, which are based on post-plating heat treatment temperature and time to produce the desired adhesion and hardness improvements. Prior to plating, substrates should be pretreated by stress relief for reducing risks of hydrogen embrittlement, peening, and racking. The coatings shall be sampled and tested accordingly to evaluate both acceptance (appearance, thickness, adhesion, and porosity) and qualification requirements (composition, microhardness, and hydrogen embrittlement). Thickness shall be assessed either by microscopical method, a magnetic induction instrument, beta backscatter method, a micrometer, weigh-plate-weigh method, coulometric method, or X-ray spectrometry. Adhesion shall be examined either by bend, impact, or thermal shock tests. And porosity shall be inspected either by ferroxyl test, boiling water test, aerated water test, or alizarin test.
SCOPE
1.1 This specification covers requirements for autocatalytic (electroless) nickel-phosphorus coatings applied from aqueous solutions to metallic products for engineering (functional) uses.
1.2 The coatings are alloys of nickel and phosphorus produced by autocatalytic chemical reduction with hypophosphite. Because the deposited nickel alloy is a catalyst for the reaction, the process is self-sustaining. The chemical and physical properties of the deposit vary primarily with its phosphorus content and subsequent heat treatment. The chemical makeup of the plating solution and the use of the solution can affect the porosity and corrosion resistance of the deposit. For more details, see ASTM STP 265 (1)2 and Refs (2) (3) (4) and (5).
1.3 The coatings are generally deposited from acidic solutions operating at elevated temperatures.
1.4 The process produces coatings of uniform thickness on irregularly shaped parts, provided the plating solution circulates freely over their surfaces.
1.5 The coatings have multifunctional properties, such as hardness, heat hardenability, abrasion, wear and corrosion resistance, magnetics, electrical conductivity provide diffusion barrier, and solderability. They are also used for the salvage of worn or mismachined parts.
1.6 The low phosphorus (2 to 4 % P) coatings are microcrystalline and possess high as-plated hardness (620 to 750 HK 100). These coatings are used in applications requiring abrasion and wear resistance.
1.7 Lower phosphorus deposits in the range between 1 and 3 % phosphorus are also microcrystalline. These coatings are used in electronic applications providing solderability, bondability, increased electrical conductivity, and resistance to strong alkali solutions.
1.8 The medium phosphorous coatings (5 to 9 % P) are most widely used to meet the general purpose requirements of wear and corrosion resistance.
1.9 The high phosphorous (more than 10 % P) coatings have superior salt-spray and acid resistance in a wide range of applications. They are used on beryllium and titanium parts for low stress properties. Coatings with phosphorus contents greater than 11.2 % P are not considered to be ferromagnetic.
1.10 The values stated in SI units are to be regarded as standard.
1.11 The following precautionary statement pertains only to the t...
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:B733 −04(Reapproved 2014)
Standard Specification for
Autocatalytic (Electroless) Nickel-Phosphorus Coatings on
Metal
This standard is issued under the fixed designation B733; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope bondability, increased electrical conductivity, and resistance to
strong alkali solutions.
1.1 This specification covers requirements for autocatalytic
(electroless) nickel-phosphorus coatings applied from aqueous 1.8 Themediumphosphorouscoatings(5to9%P)aremost
widely used to meet the general purpose requirements of wear
solutionstometallicproductsforengineering(functional)uses.
and corrosion resistance.
1.2 The coatings are alloys of nickel and phosphorus pro-
1.9 The high phosphorous (more than 10% P) coatings
ducedbyautocatalyticchemicalreductionwithhypophosphite.
have superior salt-spray and acid resistance in a wide range of
Becausethedepositednickelalloyisacatalystforthereaction,
applications.Theyareusedonberylliumandtitaniumpartsfor
the process is self-sustaining. The chemical and physical
low stress properties. Coatings with phosphorus contents
properties of the deposit vary primarily with its phosphorus
greater than 11.2% P are not considered to be ferromagnetic.
content and subsequent heat treatment. The chemical makeup
oftheplatingsolutionandtheuseofthesolutioncanaffectthe
1.10 The values stated in SI units are to be regarded as
porosity and corrosion resistance of the deposit. For more
standard.
details, see ASTM STP 265 (1) and Refs (2)(3)(4) and (5).
1.11 Thefollowingprecautionarystatementpertainsonlyto
1.3 The coatings are generally deposited from acidic solu-
the test method portion, Section 9, of this specification.This
tions operating at elevated temperatures.
standard does not purport to address all of the safety concerns,
if any, associated with its use. It is the responsibility of the user
1.4 The process produces coatings of uniform thickness on
of this standard to establish appropriate safety and health
irregularly shaped parts, provided the plating solution circu-
practices and determine the applicability of regulatory limita-
lates freely over their surfaces.
tions prior to use.
1.5 The coatings have multifunctional properties, such as
hardness, heat hardenability, abrasion, wear and corrosion
2. Referenced Documents
resistance, magnetics, electrical conductivity provide diffusion
2.1 ASTM Standards:
barrier, and solderability.They are also used for the salvage of
B368Test Method for Copper-AcceleratedAceticAcid-Salt
worn or mismachined parts.
Spray (Fog) Testing (CASS Test)
1.6 The low phosphorus (2 to 4% P) coatings are microc-
B374Terminology Relating to Electroplating
rystalline and possess high as-plated hardness (620 to 750 HK
B380Test Method for Corrosion Testing of Decorative
100). These coatings are used in applications requiring abra-
Electrodeposited Coatings by the Corrodkote Procedure
sion and wear resistance.
B487Test Method for Measurement of Metal and Oxide
Coating Thickness by Microscopical Examination of
1.7 Lower phosphorus deposits in the range between 1 and
Cross Section
3% phosphorus are also microcrystalline. These coatings are
B499Test Method for Measurement of CoatingThicknesses
used in electronic applications providing solderability,
by the Magnetic Method: Nonmagnetic Coatings on
Magnetic Basis Metals
B504Test Method for Measurement of Thickness of Metal-
This specification is under the jurisdiction of ASTM Committee B08 on
lic Coatings by the Coulometric Method
Metallic and Inorganic Coatings and is the direct responsibility of Subcommittee
B08.03 on Engineering Coatings.
Current edition approved Nov. 1, 2014. Published November 2014. Originally
approved in 1984. Last previous edition approved in 2009 as B733–09. DOI: For referenced ASTM standards, visit the ASTM website, www.astm.org, or
10.1520/B0733-04R14. contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
The boldface numbers given in parentheses refer to a list of references at the Standards volume information, refer to the standard’s Document Summary page on
end of the text. the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
B733−04 (2014)
B537Practice for Rating of Electroplated Panels Subjected G85Practice for Modified Salt Spray (Fog) Testing
to Atmospheric Exposure
2.2 Military Standards:
B567Test Method for Measurement of Coating Thickness
MIL-R-81841Rotary Flap Peening of Metal Parts
by the Beta Backscatter Method
MIL-S-13165Shot Peening of Metal Parts
B568Test Method for Measurement of Coating Thickness
MIL-STD-105Sampling Procedures and Tables for Inspec-
by X-Ray Spectrometry
tion by Attribute
B571Practice for Qualitative Adhesion Testing of Metallic
2.3 ISO Standards:
Coatings
ISO 4527 Autocatalytic Nickel-Phosphorus Coatings—
B578TestMethodforMicrohardnessofElectroplatedCoat-
Specification and Test Methods
ings
B602Test Method for Attribute Sampling of Metallic and
3. Terminology
Inorganic Coatings
3.1 Definitions:
B667Practice for Construction and Use of a Probe for
3.1.1 significant surfaces—those substrate surfaces which
Measuring Electrical Contact Resistance
the coating must protect from corrosion or wear, or both, and
B678Test Method for Solderability of Metallic-Coated
that are essential to the performance.
Products
B697Guide for Selection of Sampling Plans for Inspection
3.2 Other Definitions—Terminology B374 defines most of
of Electrodeposited Metallic and Inorganic Coatings
the technical terms used in this specification.
B762Test Method of Variables Sampling of Metallic and
Inorganic Coatings 4. Coating Classification
B849Specification for Pre-Treatments of Iron or Steel for
4.1 The coating classification system provides for a scheme
Reducing Risk of Hydrogen Embrittlement
to select an electroless nickel coating to meet specific perfor-
B850GuideforPost-CoatingTreatmentsofSteelforReduc-
mancerequirementsbasedonalloycomposition,thicknessand
ing the Risk of Hydrogen Embrittlement
hardness.
B851Specification for Automated Controlled Shot Peening
4.1.1 TYPE describes the general composition of the de-
of MetallicArticles Prior to Nickel,Autocatalytic Nickel,
positwithrespecttothephosphoruscontentandisdividedinto
or Chromium Plating, or as Final Finish
fivecategorieswhichestablishdepositproperties(seeTable1).
D1193Specification for Reagent Water
NOTE 1—Due to the precision of some phosphorus analysis methods a
D2670Test Method for Measuring Wear Properties of Fluid
deviation of 0.5% has been designed into this classification scheme.
Lubricants (Falex Pin and Vee Block Method)
Rounding of the test results due to the precision of the limits provides for
D2714Test Method for Calibration and Operation of the
aneffectivelimitof4.5and9.5%respectively.Forexample,coatingwith
Falex Block-on-Ring Friction and Wear Testing Machine
a test result for phosphorus of 9.7% would have a classification ofTYPE
V, see Appendix X5, Alloy TYPEs.
D3951Practice for Commercial Packaging
D4060Test Method for Abrasion Resistance of Organic
4.2 Service Condition Based on Thickness:
Coatings by the Taber Abraser
4.2.1 Serviceconditionnumbersarebasedontheseverityof
E60Practice for Analysis of Metals, Ores, and Related
the exposure in which the coating is intended to perform and
Materials by Spectrophotometry
minimum coating thickness to provide satisfactory perfor-
E140Hardness Conversion Tables for Metals Relationship
mance (see Table 2).
Among Brinell Hardness, Vickers Hardness, Rockwell
4.2.2 SC0 Minimum Service, 0.1 µm—This is defined by a
Hardness, Superficial Hardness, Knoop Hardness, Sclero-
minimum coating thickness to provide specific material prop-
scope Hardness, and Leeb Hardness
erties and extend the life of a part or its function.Applications
E156Test Method for Determination of Phosphorus in
include requirements for diffusion barrier, undercoat, electrical
High-Phosphorus Brazing Alloys (Photometric Method)
conductivity and wear and corrosion protection in specialized
(Withdrawn 1993)
environments.
E352TestMethodsforChemicalAnalysisofToolSteelsand
Other Similar Medium- and High-Alloy Steels
F519Test Method for Mechanical Hydrogen Embrittlement
Evaluation of Plating/Coating Processes and Service En-
AvailablefromStandardizationDocumentsOrderDesk,Bldg.4SectionD,700
vironments
Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.
G5Reference Test Method for Making Potentiodynamic
Available fromAmerican National Standards Institute (ANSI), 25 W. 43rd St.,
4th Floor, New York, NY 10036, http://www.ansi.org.
Anodic Polarization Measurements
G31Guide for Laboratory Immersion Corrosion Testing of
Metals TABLE 1 Deposit Alloy Types
G59TestMethodforConductingPotentiodynamicPolariza-
Type Phosphorus % wt
tion Resistance Measurements
I No Requirement for Phosphorus
II 1to3
III 2to4
IV 5to9
The last approved version of this historical standard is referenced on V 10 and above
www.astm.org.
B733−04 (2014)
TABLE 2 Service Conditions
4.3.4 Class 4—Heat treatment at 120 to 130°C for at least 1
Coating Thickness Requirements
h to increase adhesion of heat-treatable (age-hardened) alumi-
Minimum Coating
num alloys and carburized steel (see Note 3).
Service Condition Thickness µm in.
4.3.5 Class 5—Heat treatment at 140 to 150°C for at least 1
Specification
h to improve coating adhesion for aluminum, non age-
SC0 Minimum Thickness 0.1 0.000004
SC1 Light Service 5 0.0002 hardened aluminum alloys, copper, copper alloys and beryl-
SC2 Mild Service 13 0.0005
lium.
SC3 Moderate Service 25 0.001
4.3.6 Class 6—Heat treatment at 300 to 320°C for at least 1
SC4 Severe Service 75 0.003
h to improve coating adhesion for titanium alloys.
NOTE 3—Heat-treatable aluminum alloys such as Type 7075 can
undergo microstructural changes and lose strength when heated to over
4.2.3 SC1 Light Service,5µm—This is defined by a
130°C.
minimum coating thickness of 5 µm for extending the life of
the part. Typical environments include light-load lubricated
5. Ordering Information
wear, indoor corrosion protection to prevent rusting, and for
5.1 The following information shall be supplied by the
soldering and mild abrasive wear.
purchaser in either the purchase order or on the engineering
4.2.4 SC2 Mild Service,13µm—This is defined by mild
drawing of the part to be plated:
corrosion and wear environments. It is characterized by indus-
5.1.1 Title,ASTM designation number, and year of issue of
trial atmosphere exposure on steel substrates in dry or oiled
this specification.
environments.
5.1.2 Classification of the deposit by type, service
4.2.5 SC3 Moderate Service,25µm—This is defined by
condition, class, (see 4.1, 4.2 and 4.3).
moderate environments such as non marine outdoor exposure,
5.1.3 Specify maximum dimension and tolerance
alkali salts at elevated temperature, and moderate wear.
requirements, if any.
4.2.6 SC4 Severe Service,75µm—This is defined by a very
5.1.4 Peening, if required (see 6.5).
aggressive environment. Typical environments would include
5.1.5 The tensile strength of the material in MPa (see 6.3.1
acid solutions, elevated temperature and pressure, hydrogen
and 6.6).
sulfide and carbon dioxide oil service, high-temperature chlo-
5.1.6 Stress relief heat treatment before plating, (see 6.3).
ride systems, very severe wear, and marine immersion.
5.1.7 Hydrogen Embrittlement Relief after plating, (see
NOTE 2—The performance of the autocatalytic nickel coating depends
6.6).
to a large extent on the surface finish of the article to be plated and how
5.1.8 Significantsurfacesandsurfacesnottobeplatedmust
it was pretreated. Rough, non uniform surfaces require thicker coatings
be indicated on drawings or sample.
than smooth surfaces to achieve maximum corrosion resistance and
minimum porosity.
5.1.9 Supplemental or Special Government Requirements
such as, specific phosphorus content, abrasion wear or corro-
4.3 Post Heat Treatment Class—The nickel-phosphorus
sion resistance of the coating, solderability, contact resistance
coatings shall be classified by heat treatment after plating to
and packaging selected from Supplemental Requirements.
increase coating adhesion and or hardness (see Table 3).
5.1.10 Requirement for a vacuum, inert or reducing atmo-
4.3.1 Class 1—As-deposited, no heat treatment.
sphere for heat treatment above 260°C to prevent surface
4.3.2 Class 2—Heat treatment at 260 to 400°C to produce a
oxidation of the coating (see S3).
minimum hardness of 850 HK100.
5.1.11 Test methods for coating adhesion, composition,
4.3.3 Class 3—Heat treatment at 180 to 200°C for 2 to 4 h
thickness, porosity, wear and corrosion resistance, if required,
to improve coating adhesion on steel and to provide for
selected from those found in Section 9 and Supplemental
hydrogen embrittlement relief (see section 6.6).
Requirements.
5.1.12 Requirements for sampling (see Section 8).
TABLE 3 Classification of Post Heat Treatment
NOTE 4—The purchaser should furnish separate test specimens or
Temperature
CLASS Description Time (h)
couponsofthebasismetalfortestpurposestobeplatedconcurrentlywith
(°C)
the articles to be plated (see 8.4).
1 No Heat Treatment, As Plated
2 Heat Treatment for Maximum Hardness
TYPE I 260 20
6. Materials and Manufacture
285 16
320 8 6.1 Substrate—Defectsinthesurfaceofthebasismetalsuch
400 1
as scratches, porosity, pits, inclusions, roll and die marks, laps,
TYPE II 350 to 380 1
cracks, burrs, cold shuts, and roughness may adversely affect
TYPE III 360 to 390 1
the appearance and performance of the deposit, despite the
TYPE IV 365 to 400 1
TYPE V 375 to 400 1
observance of the best plating practice. Any such defects on
3 Adhesion on Steel 180 to 200 2 to 4
significant surfaces shall be brought to the attention of the
4 Adhesion, Carburized Steel and 120 to 130 1 to 6
Age Hardened Aluminum purchaserbeforeplating.Theproducershallnotberesponsible
5 Adhesion on Beryllium and 140 to 150 1 to 2
for coatings defects resulting from surface conditions of the
Aluminum
metal, if these conditions have been brought to the attention of
6 Adhesion on Titanium 300–320 1–4
the purchaser.
B733−04 (2014)
6.2 Pretreatment—Asuitable method shall activate the sur- purchaser. Guide B850 contains a list of post treatments,
faceandremoveoxideandforeignmate
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: B733 − 04 (Reapproved 2009) B733 − 04 (Reapproved 2014)
Standard Specification for
Autocatalytic (Electroless) Nickel-Phosphorus Coatings on
Metal
This standard is issued under the fixed designation B733; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope
1.1 This specification covers requirements for autocatalytic (electroless) nickel-phosphorus coatings applied from aqueous
solutions to metallic products for engineering (functional) uses.
1.2 The coatings are alloys of nickel and phosphorus produced by autocatalytic chemical reduction with hypophosphite.
Because the deposited nickel alloy is a catalyst for the reaction, the process is self-sustaining. The chemical and physical properties
of the deposit vary primarily with its phosphorus content and subsequent heat treatment. The chemical makeup of the plating
solution and the use of the solution can affect the porosity and corrosion resistance of the deposit. For more details, see ASTM
STP 265 (1) and Refs (2) (3) (4) and (5).
1.3 The coatings are generally deposited from acidic solutions operating at elevated temperatures.
1.4 The process produces coatings of uniform thickness on irregularly shaped parts, provided the plating solution circulates
freely over their surfaces.
1.5 The coatings have multifunctional properties, such as hardness, heat hardenability, abrasion, wear and corrosion resistance,
magnetics, electrical conductivity provide diffusion barrier, and solderability. They are also used for the salvage of worn or
mismachined parts.
1.6 The low phosphorus (2 to 4 % P) coatings are microcrystalline and possess high as-plated hardness (620 to 750 HK 100).
These coatings are used in applications requiring abrasion and wear resistance.
1.7 Lower phosphorus deposits in the range between 1 and 3 % phosphorus are also microcrystalline. These coatings are used
in electronic applications providing solderability, bondability, increased electrical conductivity, and resistance to strong alkali
solutions.
1.8 The medium phosphorous coatings (5 to 9 % P) are most widely used to meet the general purpose requirements of wear and
corrosion resistance.
1.9 The high phosphorous (more than 10 % P) coatings have superior salt-spray and acid resistance in a wide range of
applications. They are used on beryllium and titanium parts for low stress properties. Coatings with phosphorus contents greater
than 11.2 % P are not considered to be ferromagnetic.
1.10 The values stated in SI units are to be regarded as standard.
1.11 The following precautionary statement pertains only to the test method portion, Section 9, of this specification.This
standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user
of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior
to use.
This specification is under the jurisdiction of ASTM Committee B08 on Metallic and Inorganic Coatings and is the direct responsibility of Subcommittee B08.03 on
Engineering Coatings.
Current edition approved Sept. 1, 2009Nov. 1, 2014. Published December 2009November 2014. Originally approved in 1984. Last previous edition approved in 20042009
as B733 – 04.B733 – 09. DOI: 10.1520/B0733-04R09.10.1520/B0733-04R14.
The boldface numbers given in parentheses refer to a list of references at the end of the text.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
B733 − 04 (2014)
2. Referenced Documents
2.1 ASTM Standards:
B368 Test Method for Copper-Accelerated Acetic Acid-Salt Spray (Fog) Testing (CASS Test)
B374 Terminology Relating to Electroplating
B380 Test Method for Corrosion Testing of Decorative Electrodeposited Coatings by the Corrodkote Procedure
B487 Test Method for Measurement of Metal and Oxide Coating Thickness by Microscopical Examination of Cross Section
B499 Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis
Metals
B504 Test Method for Measurement of Thickness of Metallic Coatings by the Coulometric Method
B537 Practice for Rating of Electroplated Panels Subjected to Atmospheric Exposure
B567 Test Method for Measurement of Coating Thickness by the Beta Backscatter Method
B568 Test Method for Measurement of Coating Thickness by X-Ray Spectrometry
B571 Practice for Qualitative Adhesion Testing of Metallic Coatings
B578 Test Method for Microhardness of Electroplated Coatings
B602 Test Method for Attribute Sampling of Metallic and Inorganic Coatings
B667 Practice for Construction and Use of a Probe for Measuring Electrical Contact Resistance
B678 Test Method for Solderability of Metallic-Coated Products
B697 Guide for Selection of Sampling Plans for Inspection of Electrodeposited Metallic and Inorganic Coatings
B762 Test Method of Variables Sampling of Metallic and Inorganic Coatings
B849 Specification for Pre-Treatments of Iron or Steel for Reducing Risk of Hydrogen Embrittlement
B850 Guide for Post-Coating Treatments of Steel for Reducing the Risk of Hydrogen Embrittlement
B851 Specification for Automated Controlled Shot Peening of Metallic Articles Prior to Nickel, Autocatalytic Nickel, or
Chromium Plating, or as Final Finish
D1193 Specification for Reagent Water
D2670 Test Method for Measuring Wear Properties of Fluid Lubricants (Falex Pin and Vee Block Method)
D2714 Test Method for Calibration and Operation of the Falex Block-on-Ring Friction and Wear Testing Machine
D3951 Practice for Commercial Packaging
D4060 Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser
E60 Practice for Analysis of Metals, Ores, and Related Materials by Spectrophotometry
E140 Hardness Conversion Tables for Metals Relationship Among Brinell Hardness, Vickers Hardness, Rockwell Hardness,
Superficial Hardness, Knoop Hardness, Scleroscope Hardness, and Leeb Hardness
E156 Test Method for Determination of Phosphorus in High-Phosphorus Brazing Alloys (Photometric Method) (Withdrawn
1993)
E352 Test Methods for Chemical Analysis of Tool Steels and Other Similar Medium- and High-Alloy Steels
F519 Test Method for Mechanical Hydrogen Embrittlement Evaluation of Plating/Coating Processes and Service Environments
G5 Reference Test Method for Making Potentiodynamic Anodic Polarization Measurements
G31 Guide for Laboratory Immersion Corrosion Testing of Metals
G59 Test Method for Conducting Potentiodynamic Polarization Resistance Measurements
G85 Practice for Modified Salt Spray (Fog) Testing
2.2 Military Standards:
MIL-R-81841 Rotary Flap Peening of Metal Parts
MIL-S-13165 Shot Peening of Metal Parts
MIL-STD-105 Sampling Procedures and Tables for Inspection by Attribute
2.3 ISO Standards:
ISO 4527 Autocatalytic Nickel-Phosphorus Coatings—Specification and Test Methods
3. Terminology
3.1 Definitions:
3.1.1 significant surfaces—those substrate surfaces which the coating must protect from corrosion or wear, or both, and that are
essential to the performance.
3.2 Other Definitions—Terminology B374 defines most of the technical terms used in this specification.
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
The last approved version of this historical standard is referenced on www.astm.org.
Available from Standardization Documents Order Desk, Bldg. 4 Section D, 700 Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.
Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.
B733 − 04 (2014)
4. Coating Classification
4.1 The coating classification system provides for a scheme to select an electroless nickel coating to meet specific performance
requirements based on alloy composition, thickness and hardness.
4.1.1 TYPE describes the general composition of the deposit with respect to the phosphorus content and is divided into five
categories which establish deposit properties (see Table 1).
NOTE 1—Due to the precision of some phosphorus analysis methods a deviation of 0.5 % has been designed into this classification scheme. Rounding
of the test results due to the precision of the limits provides for an effective limit of 4.5 and 9.5 % respectively. For example, coating with a test result
for phosphorus of 9.7 % would have a classification of TYPE V, see Appendix X5, Alloy TYPEs.
4.2 Service Condition Based on Thickness:
4.2.1 Service condition numbers are based on the severity of the exposure in which the coating is intended to perform and
minimum coating thickness to provide satisfactory performance (see Table 2).
4.2.2 SC0 Minimum Service, 0.1 μm—This is defined by a minimum coating thickness to provide specific material properties
and extend the life of a part or its function. Applications include requirements for diffusion barrier, undercoat, electrical
conductivity and wear and corrosion protection in specialized environments.
4.2.3 SC1 Light Service, 5 μm—This is defined by a minimum coating thickness of 5 μm for extending the life of the part.
Typical environments include light-load lubricated wear, indoor corrosion protection to prevent rusting, and for soldering and mild
abrasive wear.
4.2.4 SC2 Mild Service, 13 μm—This is defined by mild corrosion and wear environments. It is characterized by industrial
atmosphere exposure on steel substrates in dry or oiled environments.
4.2.5 SC3 Moderate Service, 25 μm—This is defined by moderate environments such as non marine outdoor exposure, alkali
salts at elevated temperature, and moderate wear.
4.2.6 SC4 Severe Service, 75 μm—This is defined by a very aggressive environment. Typical environments would include acid
solutions, elevated temperature and pressure, hydrogen sulfide and carbon dioxide oil service, high-temperature chloride systems,
very severe wear, and marine immersion.
NOTE 2—The performance of the autocatalytic nickel coating depends to a large extent on the surface finish of the article to be plated and how it was
pretreated. Rough, non uniform surfaces require thicker coatings than smooth surfaces to achieve maximum corrosion resistance and minimum porosity.
4.3 Post Heat Treatment Class—The nickel-phosphorus coatings shall be classified by heat treatment after plating to increase
coating adhesion and or hardness (see Table 3).
4.3.1 Class 1—As-deposited, no heat treatment.
4.3.2 Class 2—Heat treatment at 260 to 400°C to produce a minimum hardness of 850 HK100.
4.3.3 Class 3—Heat treatment at 180 to 200°C for 2 to 4 h to improve coating adhesion on steel and to provide for hydrogen
embrittlement relief (see section 6.6).
4.3.4 Class 4—Heat treatment at 120 to 130°C for at least 1 h to increase adhesion of heat-treatable (age-hardened) aluminum
alloys and carburized steel (see Note 3).
4.3.5 Class 5—Heat treatment at 140 to 150°C for at least 1 h to improve coating adhesion for aluminum, non age-hardened
aluminum alloys, copper, copper alloys and beryllium.
4.3.6 Class 6—Heat treatment at 300 to 320°C for at least 1 h to improve coating adhesion for titanium alloys.
NOTE 3—Heat-treatable aluminum alloys such as Type 7075 can undergo microstructural changes and lose strength when heated to over 130°C.
5. Ordering Information
5.1 The following information shall be supplied by the purchaser in either the purchase order or on the engineering drawing of
the part to be plated:
5.1.1 Title, ASTM designation number, and year of issue of this specification.
5.1.2 Classification of the deposit by type, service condition, class, (see 4.1, 4.2 and 4.3).
5.1.3 Specify maximum dimension and tolerance requirements, if any.
5.1.4 Peening, if required (see 6.5).
5.1.5 The tensile strength of the material in MPa (see 6.3.1 and 6.6).
5.1.6 Stress relief heat treatment before plating, (see 6.3).
5.1.7 Hydrogen Embrittlement Relief after plating, (see 6.6).
TABLE 1 Deposit Alloy Types
Type Phosphorus % wt
I No Requirement for Phosphorus
II 1 to 3
III 2 to 4
IV 5 to 9
V 10 and above
B733 − 04 (2014)
TABLE 2 Service Conditions
Coating Thickness Requirements
Minimum Coating
Service Condition Thickness μm in.
Specification
SC0 Minimum Thickness 0.1 0.000004
SC1 Light Service 5 0.0002
SC2 Mild Service 13 0.0005
SC3 Moderate Service 25 0.001
SC4 Severe Service 75 0.003
TABLE 3 Classification of Post Heat Treatment
Temperature
CLASS Description Time (h)
(°C)
1 No Heat Treatment, As Plated
2 Heat Treatment for Maximum Hardness
TYPE I 260 20
285 16
320 8
400 1
TYPE II 350 to 380 1
TYPE III 360 to 390 1
TYPE IV 365 to 400 1
TYPE V 375 to 400 1
3 Adhesion on Steel 180 to 200 2 to 4
4 Adhesion, Carburized Steel and 120 to 130 1 to 6
Age Hardened Aluminum
5 Adhesion on Beryllium and 140 to 150 1 to 2
Aluminum
6 Adhesion on Titanium 300–320 1–4
5.1.8 Significant surfaces and surfaces not to be plated must be indicated on drawings or sample.
5.1.9 Supplemental or Special Government Requirements such as, specific phosphorus content, abrasion wear or corrosion
resistance of the coating, solderability, contact resistance and packaging selected from Supplemental Requirements.
5.1.10 Requirement for a vacuum, inert or reducing atmosphere for heat treatment above 260°C to prevent surface oxidation
of the coating (see S3).
5.1.11 Test methods for coating adhesion, composition, thickness, porosity, wear and corrosion resistance, if required, selected
from those found in Section 9 and Supplemental Requirements.
5.1.12 Requirements for sampling (see Section 8).
NOTE 4—The purchaser should furnish separate test specimens or coupons of the basis metal for test purposes to be plated concurrently with the articles
to be plated (see 8.4).
6. Materials and Manufacture
6.1 Substrate—Defects in the surface of the basis metal such as scratches, porosity, pits, inclusions, roll and die marks, laps,
cracks, burrs, cold
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.