ASTM F1967-04

Standard Consumer Safety Specification for Infant Bath Seats

SCOPE
1.1 This consumer safety specification establishes performance requirements, test methods, and labeling requirements to promote the safe use of infant bath seats. Products commonly referred to as bath rings also are included in the scope of this specification.
1.2 This consumer safety specification is intended to reduce the risk of death and minimize injury to infants resulting from use and reasonably foreseeable abuse of infant bath seats.
1.3 No infant bath seat produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein.
1.4 The following precautionary caveat pertains only to the test methods portion, Section , of this consumer safety specification:   This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.5 The test values and dimensions stated in inch-pound units are to be regarded as standard. SI values in parentheses are given for information only.

General Information

• Status: Historical
• Publication Date: 30-Jun-2004
• ICS: 97.140 - Furniture
• ICS: 97.190 - Equipment for children
• Technical Committee: F15 - Consumer Products
• Drafting Committee: F15.20 - Bath Seats

Relations

• Replaces: ASTM F1967-03 - Standard Consumer Safety Specification for Infant Bath Seats
• Effective Date: 01-Jul-2004
• Replaced By: ASTM F1967-07 - Standard Consumer Safety Specification for Infant Bath Seats
• Effective Date: 15-Jan-2007

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: F 1967 – 04
Standard Consumer Safety Specification for
1
Infant Bath Seats
This standard is issued under the fixed designation F 1967; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
INTRODUCTION
This consumer safety specification is intended to address certain incidents associated with the use
of bath seats, bath rings, and other similar devices.
The U.S. Consumer Product Safety Commission (CPSC) identified drowning incidents which
generally involved infants either tipping over, climbing out of, or sliding through the product after
being left unattended by their caregiver.
Thisspecificationdoesnotaddressincidentsinwhichbathseatsareunreasonablymisused,areused
in a careless manner that disregards the warnings and instructions that are provided with each product,
or those instances where the caregiver leaves the infant unattended in the product.
This consumer safety specification is written within the current state-of-the-art product technology.
It is intended that this specification will be updated whenever substantive information becomes
available and known to ASTM which necessitates additional requirements or justifies the revision of
existing requirements.
1. Scope 2. Referenced Documents
2
1.1 This consumer safety specification establishes perfor- 2.1 ASTM Standards:
mance requirements, test methods, and labeling requirements D 3359 Test Methods for MeasuringAdhesion by Tape Test
to promote the safe use of infant bath seats. Products com- F 404 Consumer Safety Specification for High Chairs
monly referred to as bath rings also are included in the scope F 963 Consumer Safety Specification on Toy Safety
3
of this specification. 2.2 Federal Regulations:
1.2 This consumer safety specification is intended to reduce 16 CFR 1303 Ban of Lead-Containing Paint and Certain
the risk of death and minimize injury to infants resulting from Consumer Products Bearing Lead Containing Paint
use and reasonably foreseeable abuse of infant bath seats. 16 CFR 1500 Federal Hazardous Substances Act Regula-
1.3 No infant bath seat produced after the approval date of tions, including sections:
this consumer safety specification shall, either by label or other 1500.48 Technical Requirements for Determining a
means, indicate compliance with this specification unless it Sharp Point in Toys and Other Articles Intended for Use
conforms to all requirements contained herein. by Children Under 8 Years of Age
1.4 The following precautionary caveat pertains only to the 1500.49 Technical Requirements for Determining a
test methods portion, Section 7, of this consumer safety Sharp Metal or Glass Edge in Toys and Other Articles
specification: This standard does not purport to address all of Intended for Use by Children Under 8 Years of Age
the safety concerns, if any, associated with its use. It is the 1500.50 Test Methods for Simulating Use and Abuse of
Toys and Other Articles Intended for Use by Children
responsibility of the user of this standard to establish appro-
priate safety and health practices and determine the applica- 1500.51 Test Methods for Simulating Use and Abuse of
bility of regulatory limitations prior to use. Toys and Other Articles Intended for Use by Children 18
1.5 The test values and dimensions stated in inch–pound Months of Age or Less
units are to be regarded as standard. SI values in parentheses 16 CFR 1501 Method for Identifying Toys and Other
are given for information only. Articles Intended for Use by Children Under 3 Years of
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
1
This specification is under the jurisdiction of ASTM Committee F15 on contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
Consumer Products and is the direct responsibility of Subcommittee F15.20 on Bath Standards volume information, refer to the standard’s Document Summary page on
Seats. the ASTM website.
3
Current edition approved July 1, 2004. Published July 2004. Originally approved AvailablefromU.S.GovernmentPrintingOfficeSuperintendentofDocuments,
in 1999. Last previous edition approved in 2003 as F 1967 – 03. 732 N. Capitol St., NW, Mail Stop: SDE, Washington, DC 20401.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
F1967–04
Age Which Present Choking, Aspiration, or Ingestion from unintentionally folding when properly placed in the
Hazards Because of Small Parts manufacturer’s recommended use position(s).
5.4.2 During and upon completion of the test in acc
...