ASTM C1353-98
(Test Method)Standard Test Method Using the Taber Abraser for Abrasion Resistance of Dimension Stone Subjected to Foot Traffic
Standard Test Method Using the Taber Abraser for Abrasion Resistance of Dimension Stone Subjected to Foot Traffic
SCOPE
1.1 This test method covers the establishment of an index of abrasion resistance by determination of loss of weight resulting from abrasion of dimension stone as described in Terminology C 119 and is modeled after Test Method C 501.
1.2 The values stated in metric units are to be regarded as the standard.
1.3 This test method makes use of a Taber abraser machine to determine the weight loss of dimension stone under controlled conditions.
1.4 This test method is useful in indicating the differences in abrasion resistance between the various dimension stones. This test method provides one element in comparing stones of the same type.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Standards Content (Sample)
Designation:C 1353–98
Standard Test Method Using the Taber Abraser for
Abrasion Resistance of Dimension Stone Subjected to Foot
,
Traffic
This standard is issued under the fixed designation C 1353; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope 3. Terminology
1.1 This test method covers the establishment of an index of 3.1 Definitions of Terms Specific to This Standard:
abrasionresistancebydeterminationoflossofweightresulting 3.1.1 index of abrasion resistance, n—a number calculated
from abrasion of dimension stone as described in Terminology fromtheweightlossofaspecimensubjectedtoagivennumber
C 119 and is modeled after Test Method C 501. of revolutions against a standard bonded abrasive wheel.
1.2 The values stated in metric units are to be regarded as 3.1.2 sample, n—a geometrically regular block of stone.
the standard. 3.1.3 test specimen, n—a flat prism of specified size and
1.3 This test method makes use of a Taber abraser machine shape cut from the submitted sample.
to determine the weight loss of dimension stone under con-
4. Summary of Test Method
trolled conditions.
4.1 This test method consists of mounting the stone speci-
1.4 Thistestmethodisusefulinindicatingthedifferencesin
abrasion resistance between the various dimension stones.This men in suitable holders, attaching the mounted holder to the
spindle of the Taber abraser, and subjecting the specimen to a
test method provides one element in comparing stones of the
same type. prescribed number of revolutions under abrasive wheels of
specified coarseness for a definite applied load. From the loss
1.5 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the ofweightduetoabrasion,theabrasivewearindexiscalculated
by a given formula.
responsibility of the user of this standard to establish appro-
priate safety and health practices and determine the applica-
5. Apparatus
bility of regulatory limitations prior to use.
5.1 Taber abraser machine, Model 5130 or 5150, equipped
2. Referenced Documents
with replaceable hard abrasive H-22 Calibrade wheels that can
2.1 ASTM Standards: be loaded by weights.
5.2 Table Model 200 refacing machine.
C 97 Test Methods for Absorption and Bulk Specific Grav-
ity of Dimension Stone 5.3 Vacuum pick up to remove the abraded material.
5.4 Revolution counter.
C 119 Terminology Relating to Dimension Stone
C 121 Test Method for Water Absorption of Slate 5.5 Balance with a capacity of 500 g (0.5 lb) and capable of
reading to two decimal places.
C 501 Test Method for Relative Resistance to Wear of
Unglazed Ceramic Tile by the Taber Abraser 5.6 Desiccator containing a drying agent of sufficient size to
contain samples to be tested.
5.7 Diamond saw (cut-off) with diamond-edged blade lubri-
This test method is under the jurisdiction of ASTM Committee C-18 on
cated with water.
Dimension Stone and is the direct responsibility of Subcommittee C18.01 on Test
5.8 Electrically powered drill capable of drillinga6mm( ⁄4
Methods.
in.) hole through the specimen.
Current edition approved Sept. 10, 1998. Published March 1999. Originally
published as C 1353 – 96. Last previous edition C 1353 – 96.
5.9 A ventilated drying oven.
TheTaberabraserisavailableintwomodels:the5130withasingleheadorthe
5150 with dual testing heads. The 5130 machine replaces Model 503, which is a
6. Sampling
singleheadmachine.Bothmachinesfunctioninthesamemanner.TheTaberabraser
and Model 200 wheel surfacer are available from Taber Instrument Corp., 455 6.1 Three stone samples 100 mm (4 in.) square and 10 mm
Bryant Street, North Tonawanda, NY 14120.
( ⁄8in.)thickshallconstituteasampleandshallbechosenfrom
Annual Book of ASTM Standards, Vol 04.07.
material to be tested.
Annual Book of ASTM Standards, Vol 15.02.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
C 1353–98
7. Test Specimen 8.9 Remove the specimen carefully from the table, brush
clean the dust and abrasive grains, and weigh (w ).
7.1 Three test specimens are required. Each test specimen
shall meet the following conditions:
9. Calculation
7.1.1 A slab 100 mm (4 in.) square with th
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.