ASTM B573-06
(Specification)Standard Specification for Nickel-Molybdenum-Chromium-Iron Alloys (UNS N10003, N10242)* Rod
Standard Specification for Nickel-Molybdenum-Chromium-Iron Alloys (UNS N10003, N10242)* Rod
ABSTRACT
This specification covers rods of nickel-molybdenum-chromium-iron alloys with UNS Nos. N10003 and N10242 for use in general corrosive service. Specimens shall be sampled and prepared, then tested accordingly to examine their conformance to dimensional (diameter, length, out-of-roundness, weight, and straightness), mechanical (tensile and yield strengths, and elongation), and chemical composition requirements.
SCOPE
1.1 This specification covers nickel-molybdenum-chromium-iron alloys (UNS N10003 and UNS N10242)* rod for use in general corrosive service.
1.2 The following products are covered under this specification:
1.2.1 Rods 5/16to 3/4 in. (7.94 to 19.05 mm) excl in diameter, hot or cold finished, annealed, and pickled or mechanically descaled.
1.2.2 Rods 3/4to 31/2 in. (19.05 to 88.9 mm) incl in diameter, hot or cold finished, annealed, ground, or turned.
1.3 The values stated in inch-pound units are to be regarded as the standard.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Materials Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: B573 – 06
Standard Specification for
Nickel-Molybdenum-Chromium-Iron Alloys (UNS N10003,
1
N10242)* Rod
This standard is issued under the fixed designation B573; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope E29 Practice for Using Significant Digits in Test Data to
2 Determine Conformance with Specifications
1.1 This specification covers nickel-molybdenum-
E1473 Test Methods for Chemical Analysis of Nickel,
chromium-iron alloys (UNS N10003 and UNS N10242)* rod
Cobalt, and High-Temperature Alloys
for use in general corrosive service.
1.2 The following products are covered under this specifi-
3. Terminology
cation:
3.1 Definitions of Terms Specific to This Standard:
5 3
1.2.1 Rods ⁄16 to ⁄4 in. (7.94 to 19.05 mm) excl in diameter,
3.1.1 rod, n—a product of round solid section furnished in
hot or cold finished, annealed, and pickled or mechanically
straight lengths.
descaled.
3 1
1.2.2 Rods ⁄4 to 3 ⁄2 in. (19.05 to 88.9 mm) incl in diameter,
4. Ordering Information
hot or cold finished, annealed, ground, or turned.
4.1 It is the responsibility of the purchaser to specify all
1.3 The values stated in inch-pound units are to be regarded
requirements that are necessary for the safe and satisfactory
as standard.
performance of material ordered under this specification.
1.4 This standard does not purport to address all of the
Examples of such requirements include but are not limited to
safety concerns, if any, associated with its use. It is the
the following:
responsibility of the user of this standard to become familiar
4.1.1 Dimensions—Nominal diameter and length. The
with all hazards including those identified in the appropriate
shortest usable multiple length shall be specified (Table 1).
Materials Safety Data Sheet (MSDS) for this product/material
4.1.2 Certification—State if certification or a report of test
as provided by the manufacturer, to establish appropriate
results is required (Section 15).
safety and health practices, and determine the applicability of
4.1.3 Purchaser Inspection—State which tests or inspec-
regulatory limitations prior to use.
tions are to be witnessed (Section 13).
4.1.4 Samples for Product (Check) Analysis—State whether
2. Referenced Documents
3 samples shall be furnished (9.2.2).
2.1 ASTM Standards:
B880 Specification for General Requirements for Chemical
5. Chemical Composition
Check Analysis Limits for Nickel, Nickel Alloys and
5.1 The material shall conform to the requirements as to
Cobalt Alloys
chemical composition prescribed in Table 2.
E8 Test Methods for Tension Testing of Metallic Materials
5.2 If a product (check) analysis is made by the purchaser,
the material shall conform to the requirements specified in
Table 2 subject to the permissible tolerances in Specification
1
This specification is under the jurisdiction of ASTM Committee B02 on
B880.
Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee
B02.07 on Refined Nickel and Cobalt and Their Alloys.
6. Mechanical Properties and Other Requirements
Current edition approved Dec. 1, 2006. Published January 2007. Originally
approved in 1972. Last previous edition approved in 2000 as B573 – 00. DOI:
6.1 The mechanical properties of the material at room
10.1520/B0573-06.
temperature shall conform to those shown in Table 3.
2
For ASME Boiler and Pressure Vessel Code applications see Specification
SB-573 in Section II of that Code.
7. Dimensions and Permissible Variations
* New designation established in accordance with Practice E527 and SAE J1086,
Recommended Practice for Numbering Metals and Alloys (UNS).
7.1 Diameter—The permissible variations from the speci-
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
fied diameter shall be as prescribed in Table 4.
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
7.2 Out-of-Roundness—The permissible variation in round-
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. ness shall be as prescribed in Table 4.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
B573 – 06
TABLE 1 Permissible Variations in Length of Rods 3 3
Alloy lb/in g/cm
N10003 0.317 8.78
Random mill 2 to 12 ft (610 to 3660 mm) long with not more than
N10242 0.327 9.05
lengths 25 weight % under 4 ft (1.22 m).
Multiple Furnished in multiples of a specified unit length,
7.7 Straightness—Themaximumcurvature(depthofchord)
lengths within the length limits indicated above
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:B 573–00 Designation: B573 – 06
Standard Specification for
Nickel-Molybdenum-Chromium-Iron Alloys (UNS N10003,
1
N10242)* Rod
This standard is issued under the fixed designation B573; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
2
1.1 This specification covers nickel-molybdenum-chromium-iron alloys (UNS N10003 and UNS N10242)* rod for use in
general corrosive service.
1.2 The following products are covered under this specification:
5 3
1.2.1 Rods ⁄16 to ⁄4 in. (7.94 to 19.05 mm) excl in diameter, hot or cold finished, annealed, and pickled or mechanically
descaled.
3 1
1.2.2 Rods ⁄4 to 3 ⁄2 in. (19.05 to 88.9 mm) incl in diameter, hot or cold finished, annealed, ground, or turned.
1.3 The values stated in inch-pound units are to be regarded as the standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to become familiar with all hazards including those identified in the appropriate Materials Safety Data
Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and
determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
3
2.1 ASTM Standards:
B880 Specification for General Requirements for Chemical CheckAnalysis Limits for Nickel, NickelAlloys and CobaltAlloys
E8 Test Methods for Tension Testing of Metallic Materials
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E1473 Test Methods for Chemical Analysis of Nickel, Cobalt, and High-Temperature Alloys
3. Terminology
3.1 Definitions of Terms Specific to This Standard:
3.1.1 rodrod, n—a product of round solid section furnished in straight lengths.
4. Ordering Information
4.1 It is the responsibility of the purchaser to specify all requirements that are necessary for the safe and satisfactory
performance of material ordered under this specification. Examples of such requirements include but are not limited to the
following:
4.1.1 Dimensions—Nominal diameter and length. The shortest usable multiple length shall be specified (Table 1).
4.1.2 Certification—State if certification or a report of test results is required (Section 15).
4.1.3 Purchaser Inspection—State which tests or inspections are to be witnessed (Section 13).
4.1.4 Samples for Product (Check) Analysis—State whether samples shall be furnished (9.2.2).
5. Chemical Composition
5.1 The material shall conform to the requirements as to chemical composition prescribed in Table 2.
1
ThisspecificationisunderthejurisdictionofASTMCommitteeB02onNonferrousMetalsandAlloysandisthedirectresponsibilityofSubcommitteeB02.07onRefined
Nickel and Cobalt and Thier Alloys.
Current edition approved May 10, 2000. Published June 2000. Originally published as B 573–72. Last previous edition B 573–95a.on Refined Nickel and Cobalt andTheir
Alloys.
Current edition approved Dec. 1, 2006. Published January 2007. Originally approved in 1972. Last previous edition approved in 2000 as B573 – 00. DOI:
10.1520/B0573-06.
2
For ASME Boiler and Pressure Vessel Code applications see Specification SB-573 in Section II of that Code.
* New designation established in accordance with ASTMPractice E527 and SAE J1086, Recommended Practice for Numbering Metals and Alloys (UNS).
3
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
, Vol 02.04.volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
B573 – 06
TABLE 1 Permissible Variations in Length of Rods
Random mill 2 to 12 ft (610 to 3660 mm) long with not more than
lengths 25 weight % under 4 ft (1.22 m).
Multiple Furnished in multiples of a specified unit length,
lengths within the length limits indicated above. For each
1
multiple, an allowance of ⁄4 in. (6.35 mm) shall
be made for cutting, unless otherwise specified. At
the manufacturer’s option, individual specified unit
lengths may be furnished.
Nominal Specified nominal lengths having a
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.