Standard Specification for Asphalt Shingles Made from Glass Felt and Surfaced with Mineral Granules

ABSTRACT
This specification deals with the standards for asphalt roofing in shingle form, composed of glass felt or felts impregnated and coated on both sides with asphalt, and surface on the weather side with minerals. Physical requirements of the shingles such as behavior on melting, tear strength, wind resistance, fire resistance, softening point, and pliability shall be measured immediately after packaging or at a reasonable time. Physical and performance requirements after application and during in-service use are however beyond the scope of this specification.
SCOPE
1.1 This specification covers asphalt roofing in shingle form, composed of glass felt or felts impregnated and coated on both sides with asphalt, and surfaced on the weather side with mineral granules. This specification is designed for the evaluation of products as manufactured. The test methods, physical requirements, and minimum masses are to be measured immediately after packaging or at a reasonable time, as agreed upon between buyer and seller, after manufacture and before installation. Physical and performance requirements after application and during in-service use of the products described herein are beyond the scope of this material specification.  
1.2 Shingles meeting this specification are intended to be applied with a headlap of not less than 51 mm (2 in.).
1.3 The shingles shall be supplied with a factory-applied self-sealing adhesive or be designed to be locked together during installation of the shingles.
1.4 The values stated in SI units are to be regarded as the standard.
1.5 The following safety hazards caveat pertains only to the test method described in this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
31-Dec-2008
Current Stage
Ref Project

Relations

Buy Standard

Technical specification
ASTM D3462-09 - Standard Specification for Asphalt Shingles Made from Glass Felt and Surfaced with Mineral Granules
English language
5 pages
sale 15% off
Preview
sale 15% off
Preview
Technical specification
REDLINE ASTM D3462-09 - Standard Specification for Asphalt Shingles Made from Glass Felt and Surfaced with Mineral Granules
English language
5 pages
sale 15% off
Preview
sale 15% off
Preview
Technical specification
REDLINE ASTM D3462-09 - Standard Specification for Asphalt Shingles Made from Glass Felt and Surfaced with Mineral Granules
English language
5 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D 3462 – 09
Standard Specification for
Asphalt Shingles Made from Glass Felt and Surfaced with
1
Mineral Granules
This standard is issued under the fixed designation D 3462; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope D36 Test Method for Softening Point of Bitumen (Ring-
and-Ball Apparatus)
1.1 This specification covers asphalt roofing in shingle
D 228 Test Methods for Sampling, Testing, andAnalysis of
form, composed of glass felt or felts impregnated and coated
Asphalt Roll Roofing, Cap Sheets, and Shingles Used in
on both sides with asphalt, and surfaced on the weather side
Roofing and Waterproofing
with mineral granules. This specification is designed for the
D 1079 Terminology Relating to Roofing and Waterproof-
evaluation of products as manufactured. The test methods,
ing
physical requirements, and minimum masses are to be mea-
D 1922 Test Method for Propagation Tear Resistance of
sured immediately after packaging or at a reasonable time, as
Plastic Film and Thin Sheeting by Pendulum Method
agreed upon between buyer and seller, after manufacture and
D 3161 Test Method for Wind-Resistance of Asphalt
before installation. Physical and performance requirements
Shingles (Fan-Induced Method)
after application and during in-service use of the products
D 4977 Test Method for Granule Adhesion to Mineral
described herein are beyond the scope of this material speci-
Surfaced Roofing by Abrasion
fication.
E 108 Test Methods for Fire Tests of Roof Coverings
1.2 Shingles meeting this specification are intended to be
applied with a headlap of not less than 51 mm (2 in.).
3. Terminology
1.3 The shingles shall be supplied with a factory-applied
3.1 Definitions:
self-sealing adhesive or be designed to be locked together
3.1.1 For definitions of terms, see Terminology D 1079.
during installation of the shingles.
3.1.2 For testing purposes, underTest Methods D 228, glass
1.4 The values stated in SI units are to be regarded as the
felt shall be considered as felt.
standard.
1.5 The following safety hazards caveat pertains only to the
4. Materials and Manufacture
test method described in this specification: This standard does
4.1 The glass felt shall be a thin porous sheet composed
not purport to address all of the safety concerns, if any,
predominately of fine glass fibers uniformly deposited in a
associated with its use. It is the responsibility of the user of this
nonwoven pattern. It is permitted to reinforce the glass felt
standard to establish appropriate safety and health practices
withrandomorparallel-orientedglassyarns,orboth,whichare
and determine the applicability of regulatory limitations prior
permitted to be gathered or twisted, bonded or unbonded. The
to use.
felt shall contain a substantially water-insoluble binding agent.
4.2 In the process of manufacture, one or more thicknesses
2. Referenced Documents
2
of glass felt shall be impregnated with an asphaltic material.
2.1 ASTM Standards:
When more than one thickness of felt is used, the mats shall be
D5 Test Method for Penetration of Bituminous Materials
adhered to each other with a continuous layer of asphaltic
material between adjacent felts. The nature of the asphaltic
1
This specification is under the jurisdiction of ASTM Committee D08 on
material and the thickness of the adhering layers shall ensure a
Roofing and Waterproofing and is the direct responsibility of Subcommittee D08.02
firm bond between adjacent glass felts. The single felt or
on Prepared Roofings, Shingles and Siding Materials.
laminated felts shall then be coated on both sides with a hot
Current edition approved Jan. 1, 2009. Published January 2009. Originally
approved in 1983. Last previous edition approved in 2007 as D 3462 – 07.
asphaltic coating.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
4.3 Theasphalticmaterialusedtoimpregnate,laminate,and
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
coat the glass felt, in any or all of these functions, is permitted
Standards volume information, refer to the standard’s Document Summary page on
to be compounded with a mineral stabilizer. Glass fibers are
the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
D3462–09
permitted to be compounded with the asphalt in addition to, or 7.2 The weather surface shall be uniform in finish and may
instead of, the mineral
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:D3462–07 Designation: D 3462 – 09
Standard Specification for
Asphalt Shingles Made from Glass Felt and Surfaced with
1
Mineral Granules
This standard is issued under the fixed designation D 3462; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope
1.1 This specification covers asphalt roofing in shingle form, composed of glass felt or felts impregnated and coated on both
sides with asphalt, and surfaced on the weather side with mineral granules. This specification is designed for the evaluation of
products as manufactured. The test methods, physical requirements, and minimum masses are to be measured immediately after
packaging or at a reasonable time, as agreed upon between buyer and seller, after manufacture and before installation. Physical
and performance requirements after application and during in-service use of the products described herein are beyond the scope
of this material specification.
1.2 Shingles meeting this specification are intended to be applied with a headlap of not less than 51 mm (2 in.).
1.3 The shingles shall be supplied with a factory-applied self-sealing adhesive or be designed to be locked together during
installation of the shingles.
1.4 The values stated in SI units are to be regarded as the standard.
1.5 The following safety hazards caveat pertains only to the test method described in this specification: This standard does not
purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to
establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
D5 Test Method for Penetration of Bituminous Materials
D36 Test Method for Softening Point of Bitumen (Ring-and-Ball Apparatus)
D 228 Test Methods for Sampling, Testing, and Analysis of Asphalt Roll Roofing, Cap Sheets, and Shingles Used in Roofing
and Waterproofing
D 1079 Terminology Relating to Roofing and Waterproofing
D 1922 Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
D 3161 Test Method for Wind-Resistance of Asphalt Shingles (Fan-Induced Method)
D 4977 Test Method for Granule Adhesion to Mineral Surfaced Roofing by Abrasion
E 108 Test Methods for Fire Tests of Roof Coverings
3. Terminology
3.1 Definitions:
3.1.1 For definitions of terms, see Terminology D 1079.
3.1.2 For testing purposes, under Test Methods D 228, glass felt shall be considered as felt.
4. Materials and Manufacture
4.1 The glass felt shall be a thin porous sheet composed predominately of fine glass fibers uniformly deposited in a nonwoven
pattern. It is permitted to reinforce the glass felt with random or parallel-oriented glass yarns, or both, which are permitted to be
gathered or twisted, bonded or unbonded. The felt shall contain a substantially water-insoluble binding agent.
4.2 In the process of manufacture, one or more thicknesses of glass felt shall be impregnated with an asphaltic material. When
1
This specification is under the jurisdiction ofASTM Committee D08 on Roofing and Waterproofing and is the direct responsibility of Subcommittee D08.02 on Prepared
Roofings, Shingles and Siding Materials.
Current edition approved Jan. 15, 2007.1, 2009. Published February 2007.January 2009. Originally approved in 1983. Last previous edition approved in 20052007 as
D 3462 – 057.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
D3462–09
more than one thickness of felt is used, the mats shall be adhered to each other with a continuous layer of asphaltic material
between adjacent felts. The nature of the asphaltic material and the thickness of the adhering layers shall ensure a firm bond
between adjacent glass felts. The single felt or laminated felts shall then be coated on both sides with a hot asphaltic coating.
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:D3462–07 Designation: D 3462 – 09
Standard Specification for
Asphalt Shingles Made from Glass Felt and Surfaced with
1
Mineral Granules
This standard is issued under the fixed designation D 3462; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope
1.1 This specification covers asphalt roofing in shingle form, composed of glass felt or felts impregnated and coated on both
sides with asphalt, and surfaced on the weather side with mineral granules. This specification is designed for the evaluation of
products as manufactured. The test methods, physical requirements, and minimum masses are to be measured immediately after
packaging or at a reasonable time, as agreed upon between buyer and seller, after manufacture and before installation. Physical
and performance requirements after application and during in-service use of the products described herein are beyond the scope
of this material specification.
1.2 Shingles meeting this specification are intended to be applied with a headlap of not less than 51 mm (2 in.).
1.3 The shingles shall be supplied with a factory-applied self-sealing adhesive or be designed to be locked together during
installation of the shingles.
1.4 The values stated in SI units are to be regarded as the standard.
1.5 The following safety hazards caveat pertains only to the test method described in this specification: This standard does not
purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to
establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
D5 Test Method for Penetration of Bituminous Materials
D36 Test Method for Softening Point of Bitumen (Ring-and-Ball Apparatus)
D 228 Test Methods for Sampling, Testing, and Analysis of Asphalt Roll Roofing, Cap Sheets, and Shingles Used in Roofing
and Waterproofing
D 1079 Terminology Relating to Roofing and Waterproofing
D 1922 Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
D 3161 Test Method for Wind-Resistance of Asphalt Shingles (Fan-Induced Method)
D 4977 Test Method for Granule Adhesion to Mineral Surfaced Roofing by Abrasion
E 108 Test Methods for Fire Tests of Roof Coverings
3. Terminology
3.1 Definitions:
3.1.1 For definitions of terms, see Terminology D 1079.
3.1.2 For testing purposes, under Test Methods D 228, glass felt shall be considered as felt.
4. Materials and Manufacture
4.1 The glass felt shall be a thin porous sheet composed predominately of fine glass fibers uniformly deposited in a nonwoven
pattern. It is permitted to reinforce the glass felt with random or parallel-oriented glass yarns, or both, which are permitted to be
gathered or twisted, bonded or unbonded. The felt shall contain a substantially water-insoluble binding agent.
4.2 In the process of manufacture, one or more thicknesses of glass felt shall be impregnated with an asphaltic material. When
1
This specification is under the jurisdiction ofASTM Committee D08 on Roofing and Waterproofing and is the direct responsibility of Subcommittee D08.02 on Prepared
Roofings, Shingles and Siding Materials.
Current edition approved Jan. 15, 2007.1, 2009. Published February 2007.January 2009. Originally approved in 1983. Last previous edition approved in 20052007 as
D 3462 – 057.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
D3462–09
more than one thickness of felt is used, the mats shall be adhered to each other with a continuous layer of asphaltic material
between adjacent felts. The nature of the asphaltic material and the thickness of the adhering layers shall ensure a firm bond
between adjacent glass felts. The single felt or laminated felts shall then be coated on both sides with a hot asphaltic coating.
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.